Aleratec 13 DVD CD LightScribe Duplicator SA User Guide

							www.aleratec.com15
Overview
Other Label Printing Related Options
There are other label printing related operations available as described below:
Menu 3: Copy+Print
This function allows you to perform the disc duplication then the disc labeling 
operation as part of one process.  Just flip the disc from the data side to the label   
side after each duplication pass.
To use this function, the data file required for duplication and the label file required 
for labeling will need to be preloaded onto the duplicator’s internal hard drive.
Menu 12.1: Load Label
This operation allows you to load your existing label file from a disc onto the 
duplicator’s hard drive (HDD). 
Menu 12.2: Rename Label
This operation allows you to rename your existing label in the duplicator’s hard 
drive. 
Menu 12.3: Delete Label
This operation allows you to delete your existing label in the duplicator’s hard drive. 
Menu 12.4: Print Surface ID
This operation allows you reveal the ID code of the media’s label surface for tech 
support troubleshooting purposes.
Menu 12.5: Select Loading Drive
This operation allows you to choose the default drive to read the label file(s) on to 
the duplicator’s hard drive when you perform the Load Label operation.  
						

							www.aleratec.com16
Overview
Control Functions
For detailed descriptions of each control function and feature see the Menu Overview 
section beginning on page 59 of this User Guide. 
Control Functions
1. Copy2. Print3. Copy + Print4. Test5. Compare6. Test + Copy7. Copy + Compare8. Select Burn Speed9. Select Source10. Erase11. Hard Drive Setup1. Select Partition2. Load Partition3. Rename Partition4. Delete Partition5. Partition Info6. Select Loading Drive7. Format Hard Drive12. Print Setup1. Load Label 2. Rename Label3. Delete Label4. Print Surface Info5. Label Info6. Select Loading Drive13. Mix Audio Tracks14. Setup1. Language2. Auto Start3. Read Error Skip4. CD Writing Mode5. Max Audio 6. Buzzer7. Start Up Menu8. Screen Saver9. Duplication Mode10. Counter11. DVD+R High Compatibility12. IRSC 13. Disable Drivers14. USB Connection15. Overburn
15. Utilities1. Disc Info2. Prescan 3. System Info4. Device Info5. Load Default6. Update Firmware7. Save16. Manage Accounts17. Autocopy18. Shutdown  
						

							www.aleratec.com17
Stand-Alone LightScribe Duplicator SA: Tutorials
Making Disc-to-Disc Copies
This process copies a Master Disc to several blank discs simultaneously. Due to 
the nature of simultaneous disc duplication, a good quality Master Disc and lower 
recording speeds maybe necessary to ensure high success and quality duplications 
rates.
1. Turn on the duplicator. After the duplicator has booted up, you will see the 
following display:
2. Make sure the Source Drive is set to the DVD-ROM drive.
It is very important to make sure that your current Source Drive is the *DVD-
ROM in order to avoid unnecessary error messages. To check the Source Drive, 
do the following:
a. Use UP or DOWN arrow buttons to navigate to the following screen:
b. Press ENT to enter Select Source menu and you will see the following:
Make sure it is located at “Drive 2 Port 2.1”. If not, press the UP or 
DOWN navigation button to search for it.
c. Press ENT to submit your selection.
3. Go back to the “COPY” menu.
a. Use UP or DOWN arrow button to navigate to the following screen:
DUPLICATOR 1.001. COPYCOPYTESTPRINTSOURCE
ESCENT


COPYTESTPRINTSOURCE
ESCENT


DUPLICATOR 1.009. Select Source
COPYTESTPRINTSOURCE
ESCENT


Drive 2 Port 2.1  DVD-ROM
COPYTESTPRINTSOURCE
ESCENT


DUPLICATOR  1.001. COPY                  
						

							www.aleratec.com18
Stand-Alone LightScribe Duplicator SA: Tutorials
4. Start the Copy Process.
a. Insert your Master Disc and blank discs into their corresponding tray(s) and 
press the ENT button. You will see the following display:
b. “Duplication Mode” offers three choices:
 ▪Load and Copy
 ▪On the Fly
 ▪Prompt
Press UP or DOWN arrow button to display your desired mode. Press the 
ENT button to confirm.
c. “No Counter” can be used when you prefer to copy continuously with no 
interruption. (It will still count the number of copies, but it will not notify 
you when to stop.) To select the “No Counter”, press ENT when you see 
the above screen. Then skip to step “d” on page 21 of this User Guide.
“Specify Counter” lets you to select the number of copies you want to 
make. The duplicator will count the number of copies you’ve made and 
prompt you when the desired number of copies has been completed. 
Press ENT button to select. Enter between 1 to 9999 copies. 
Enter a 4-digit number to specify the number of copies you want to make. 
To specify a number less than 4 digits, fill the leading spaces with “0”s 
(any leading “0” will be skipped). For example, “0234” will give you two 
hundred and thirty four copies, and “0010” will give you ten copies. 
COPYTESTPRINTSOURCE
ESCENT


Duplication Mode:Load and Copy
COPYTESTPRINTSOURCE
ESCENT


Counter:No Counter
COPYTESTPRINTSOURCE
ESCENT


Counter:Specify Counter
COPYTESTPRINTSOURCE
ESCENT


Specify Counter:[0   ]  OK?                  
						

							www.aleratec.com19
Stand-Alone LightScribe Duplicator SA: Tutorials
Making Disc-to-Disc Copies - continued 
Example:
To enter a value of 21 copies, do the following
Make sure the cursor is located at the first position:
i. Press DOWN button consecutively until “0” is displayed.
ii. Press ENT button once to move the cursor to the next position.
iii. Press DOWN button consecutively until “0” is displayed.
iv. Press ENT button once to move the cursor to the next position.
v. Press DOWN button consecutively until “2” is displayed.
vi. Press ENT button once to move the cursor to the next position.
vii. Press DOWN button consecutively until “1” is displayed.
viii. Now, “0021” is displayed, press ENT once and the cursor moved to OK.
ix. Then, press ENT once to submit your counter value.
Now you will see the following screen:
OR
COPYTESTPRINTSOURCE
ESCENT


Specify Counter:[X   ]  OK?
COPYTESTPRINTSOURCE
ESCENT


Preparing...Waiting for Master
COPYTESTPRINTSOURCE
ESCENT


Preparing...Waiting for Blanks              
						

							www.aleratec.com20
Stand-Alone LightScribe Duplicator SA: Tutorials
Note: If either one of the PREVIOUS 2 screens are displayed for 
more than 2 minutes, please check your Master Disc or blank 
discs for quality.
d. Allow 5-10 seconds for the duplicator to detect both your Master Disc and 
blank discs. After your Master Disc and blank discs have been recognized, 
you will see the following display:
Note: “3” indicates there are 3 discs recognized by the Writer 
Tray. For this example, number of discs could be up to three.
Note: By default, the “Auto Start” setting is set to “Auto”. For 
example, if your duplicator has detected 3 blank discs and 
didn’t detect any additional blank discs within 30 seconds, the 
duplication will start automatically.
When the number of blank discs inserted matches the number of discs 
detected press ENT	to confirm. You will see the following display:
Note: Give the duplicator 10-15 seconds to recognize all the 
blank discs. If the number of blank discs you inserted doesn’t 
match the number of discs detected...
COPYTESTPRINTSOURCE
ESCENT


Preparing...3 Disc Detected, Go?
COPYTESTPRINTSOURCE
ESCENT


Processing...  Please Wait          
						

							www.aleratec.com21
Stand-Alone LightScribe Duplicator SA: Tutorials
Making Disc-to-Disc Copies - continued
e. 2 or 3 seconds after copying begins the following “Copy Progress” screen 
will appear:
Note: It is normal to see the progress indicator stay at 0-10% and 
at 100% for approximately 30 seconds during CD duplication. 
Additionally it is normal to see the progress indicator stay at 0-10% 
and at 100% for up to 1 minute during DVD duplication. There 
is a delay caused by the initializing and finalizing stage of disc 
duplication. Due to this delay, it is normal to see progress indicators 
stay at 100% for up to several minutes before moving on. Once the 
disc duplication is completed, successful copies will be ejected and 
you will see the following display:
Counter SpecifiedNo Counter
“4012MB” indicates the capacity of the Master Disc.
“481MB” indicates the current progress of the duplication in terms of MB.
“12%” indicates the current progress of the duplication.
“0/21” indicates you have a project size of 21 copies and you have made 0 copies so far.
“4012MB” indicates the capacity of the Master Disc.
“481MB” indicates the current progress of the duplication in terms of MB.
“12%” indicates the current progress of the duplication.
“0” indicates that you have made 0 copies so far.
“FAIL 0” indicates that you have no failure in this run.
“PASS 3” indicates that you’ve just made 3 successful copies.
“3” indicates that you’ve successfully copied 3 copies so far.
COPYTESTPRINTSOURCE
ESCENT


Copying...  4012MB0/21  12%    481MBCOPYTESTPRINTSOURCE
ESCENT


Copying...   4012MB       0  12%    481MB
COPYTESTPRINTSOURCE
ESCENT


PASS  3  FAIL  0  (   3)Waiting for Blanks                         
						

							www.aleratec.com22
Stand-Alone LightScribe Duplicator SA: Tutorials
To continue making additional copies, remove the successfully completed copies 
from the ejected trays and replace with blank discs. To terminate your project and 
return to the main menu, press ESC. 
If you’ve specified a counter value you will see the following display when your 
project is completed:
If you see above message, you can press ENT to go back to main menu.
Note: If you enabled the counter and the number of blank discs you 
have inserted is greater than the number you requested, you will 
receive a message indicating you have inserted more discs than 
what you need. You can continue to copy or you can eject the extras 
discs.
Note: Failed discs will not be ejected automatically. You will need to 
manually eject these. 
COPYTESTPRINTSOURCE
ESCENT


21 Disc CopiedPress OK to Finish      
						

							www.aleratec.com23
Stand-Alone LightScribe Duplicator SA: Tutorials
Load Master Disc onto the Hard Drive
In order to copy from the Hard Drive, you are required to load your Master Disc 
onto a hard drive partition.
The number of partitions the hard drive can hold is determined by the capacity of 
your hard drive and the size of the partitions you created.
For example, if you have an 80GB Hard Drive with a system capacity of 74GB.* 
You can load 74 CDs or 19 DVDs (given a 4GB average capacity).
*There are many factors that could contribute to the capacity 
difference between the advertised capacity and the actual capacity:
 ▪Hard Drive Manufactures use conversion rate of 1GB = 1 Billion Bytes 
or 1000^3 Bytes. However, most Operating Systems, including our 
Duplication System use standard conversion rate of 1GB = 1.074 Billion 
Bytes or 1024^3 Bytes. Therefore, for an advertised 80GB Hard Drive (80 
Billion Bytes), the Duplication System capacity is actually 74.5 Billion 
Bytes (74.5GB).
 ▪In addition, we round off all fractions of a GB to the lower whole number. 
That means for a hard drive that has a 74.5GB system capacity, we only 
recognize and utilize 74GB.
The following steps will show you how to load your Master Disc into the installed 
Hard Drive as a partition and copy the stored partition onto blank discs. This process 
is recommended for mass volume production.
To load your Master Disc onto a hard drive partition, please do the following:
1. Make sure the Source is set to the Hard Drive.
It is very important to make sure the Source is set for the Hard Drive in order to 
avoid unnecessary error messages. To check what the Source is set to, please do 
the following:
a. Use UP or DOWN arrow button to navigate to the following screen.
b. Press ENT to enter “Select Source” menu and you will see the following:
Make sure it is located at “Hard Drive”. If not, press the UP or DOWN 
arrow button to search for it.
DUPLICATOR 1.009. Select SourceCOPYTESTPRINTSOURCE
ESCENT


Hard Drive Port 0Hitachi HDT25025VLAT80COPYTESTPRINTSOURCE
ESCENT

          
						

							www.aleratec.com24
Stand-Alone LightScribe Duplicator SA: Tutorials
Load Master Disc onto the Hard Drive - continued 
c. Press ENT to submit your selection. After your selection has been 
submitted, you will see the following display:
2. Load your Master Disc onto the Hard Drive.
a. Use the UP or DOWN arrow button to navigate to the following screen.
b. Press ENT to enter “Hard Drive Setup” menu and you will see the 
following display:
c. Load your Master Disc on to the Hard Drive. To do so, use the UP or 
DOWN arrow button to navigate to the following screen.
d. Press ENT to enter “Load Partition” menu and you will see the following 
display:
The “228GB” indicates the available capacity of your hard drive in term of GB.
DUPLICATOR 1.009. Select SourceCOPYTESTPRINTSOURCE
ESCENT


DUPLICATOR 1.0011. Hard Drive SetupCOPYTESTPRINTSOURCE
ESCENT


Hard Drive Setup1. Select PartitionCOPYTESTPRINTSOURCE
ESCENT


Hard Drive Setup2. Load PartitionCOPYTESTPRINTSOURCE
ESCENT


Load Partition [     228GB]Load-> New PartitionCOPYTESTPRINTSOURCE
ESCENT

