Aleratec RoboJet Disc AutoPrinter with Continuous Ink System User Guide

www.aleratec.com5
In\ftallation
Unpacking the Unit
Set the components on a flat, level surface that will hold the printer, autoloader 
and your PC. Next, carefully remove the packing material that contains the above 
items. Then place all shipping materials back into the shipping carton for future 
use.
Note: It is important to\s keep t\fe original \ss\fipping container \sand packaging. 
In t\fe e\bent you mi\ssplace your packagi\sng and need to s\fip\s t\fe RoboJet Disc 
AutoPrinter wit\f Co\sntinuous...

www.aleratec.com
6
In\ftallation
Minimum Hardware and\i Software Requireme\int\f
It is recommended that you operate your new RoboJet RoboJet Disc AutoPrinter 
with Continuous Ink System with PC systems that exceed the minimum hardware 
requirements to ensure smooth and efficient operation.
Pentium III 1GHz, 1GB DRAM (2GB DRAM recommended) 
Windows 7, XP, Vista, 2000 SP4 
Available USB2.0 port
 
Operation
Do not move any part of the RoboJet Disc AutoPrinter with Continuous Ink 
System during operation....

www.aleratec.com7
In\ftallation
In\ftalling Aleratec’\f RoboJet Di\fc AutoPrinter Software 
 
Note: Be sure to install the printer first by following the instructions 
included in the printer box. 
    
1.  When you place the installation CD into your computer’s drive, the 
installation screen should appear.
If you do not see this, it means that the Windows autorun feature is disabled 
and you have to start this program manually. In order to do it you have to go 
to “My Computer” (Windows XP) or...

www.aleratec.com
8
In\ftallation
In\ftalling Aleratec’\f RoboJet Di\fc AutoPrinter Software
5.  The setup wizard will guide you through several screens to configure 
the installation.  Choose a “Typical” setup and continue on until the 
installation is complete.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
6.  Once the installation has been completed successfully, you will see 
shortcuts for the “Aleratec RoboJet Disc Autoloader” application on 
your desktop. 
 
 
 
 
 
 
   

www.aleratec.com9
In\ftallation
1. Make sure t\fat t\fe p\srinter is OFF w\fen \ssetting up t\fe disc \sautoloader. 
Open manual feed d\soor on printer. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Set Up Di\fc Autoloader
2. Remo\be printer “pap\ser feed” tray.   

www.aleratec.com
10
In\ftallation
3.  Insert disc autoloa\sder into printer “\sdisc tray” slots at \sa 45 degree 
angle. 
4.  Lay disc autoloader\s down on table. 
45  

www.aleratec.com11
In\ftallation
6. Attac\f disc bin. 
5. 
Insert disc \folder p\sosts.   

www.aleratec.com
12
In\ftallation
7.  Attac\f power cord a\snd plug into power\s outlet.
8.  Attac\f included USB \scord into included\s USB2.0 \fub and atta\sc\f \fub to 
t\fe computer. Bot\f t\fe printer a\snd disc autoloader \smust be connected t\so 
your PC using t\fe in\scluded USB2.0 \fub in\s order for t\fe disc\s autoloader 
software to work pr\soperly.
Note: Make sure t\fe Robo\sJet software/dri\ber\s installation is co\smplete before 
connecting t\fe disc\s autoloader to t\fe \scomputer.
USB2.0...

www.aleratec.com13
U\fing the RoboJet Di\i\fc AutoPrinter
Powering on the Printe\ir
 
The design of the printer does not allow for it to power on properly with a disc 
tray attached.  Because of this, the disc autoloader is designed with a physical 
“Printer Mode Switch” that can be used to simulate the absence of the disc tray .  
Whenever the printer is powered on, the Printer Mode Switch must be in the 
paper mode which is indicated by a paper icon indicating the switch position.  
Once the printer...

www.aleratec.com
14
U\fing the RoboJet Di\i\fc AutoPrinter
Powering on the Printe\ir
2.  Power on the printer. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
3.  Wait for printer to initialize and show a steady green indicator on its 
power button.