Alfa Router AIP-W610 User Manual

7.  Click the drop list to select the encryption type for your wireless network. Fill in the 
parameters for the encryption type you select and click finish to complete 
configuration. 
 
16 
 
  

Operation Mode 
 
To select an operation mode for this router, click on the mode that you want to perform 
and click the 
 button to execute. 
 
17 
 
  

 Wireless 
 
Wireless Access Point builds a wireless LAN and can let all PCs equipped with 
IEEE802.11b/g wireless network adaptor connect to your Intranet. It supports 
WEP encryption and MAC address filter to enhance the security of your wireless 
network. 
Basic Settings   
You can set up the configuration of your Wireless and monitor the 
Wireless Clients associate with your AP.   
 
 Configuration 
18 
Disable Wireless LAN 
Interface 
To Disable interface of Wireless LAN 
Band To select a band for...

Channel Number The channel used by the wireless LAN. All 
devices in the same wireless LAN should use 
the same channel. 
Associated Clients Click Show Active Clients button, then an 
Active Wireless Client Table will pop up. You 
can see the status of all active wireless 
stations that are connecting to the access 
point. 
Enable Universal   
Repeater Mode Mark this checkbox to enable Universal 
Repeater Mode which acts this device as an 
AP and client simultaneously. 
SSID of Extended   
Interface...

Tx Packet The number of transmitted packets that are sent out 
from this active wireless station. 
Rx Packet The number of received packets that are received by 
this active wireless station. 
TX Rate The transmission rate 
Power Saving Shows if the wireless client is in Power Saving mode 
Expired Time This is the time in second before dissociation. If the 
wireless keeps idle longer than the expired time, this 
wireless router will dissociate it. The wireless client 
station has to associate again when...

Advanced Settings 
You can set advanced wireless LAN parameters of this router. The 
parameters include Authentication Type, Fragment Threshold, RTS 
Threshold, Beacon Interval, Data Rate, Preamble Type, Broadcast SSID, 
IAPP and 802.11g Protection. We recommend not changing these 
parameters unless you know what changes will be there on this router. 
 
   Configuration  
21 
Open System 
mode Wireless AP can associate with this wireless 
router without WEP encryption. 
Shared Key 
mode 
You should also...

Fragment 
Threshold To specifies the maximum size of packet during the data 
transition. The lower values you set, the worst performance it
 
will be.   
RTS Threshold 
If the packet size is smaller the RTS threshold, the wireless 
router will not send this packet by using the RTS/CTS 
mechanism. 
Beacon Interval The period of time how long a beacon is broadcasted. 
Data Rate 
The Data Rate is the data packets limitation this wireless 
router can transmit. The wireless router will use the highest...

Security  
At the page, you can set up the WEP, WPA Encryption to ensure the 
security of your Wireless. 
 
 
   Configuration  
23 
Encryption To enable WEP, WPA, WPA2 and WPA2 
Mixed encryption modes, select the option in 
the drop list. If you select none, any data will 
be transmitted without Encryption and any 
station can access the router. 
Use 802.1x Authentication To enable the 802.1x, Click the check box of 
the item. 
WPA Authentication Mode There are two items, “Enterprise 
(WPA-Radius)” and...

WPA2 Cipher Suite Select the WPA2 Cipher Suite to be TKIP or 
AES 
Pre-Shared key Format To decide the format, select what you need in 
the drop list. 
Pre-shared Key Enter the Pre-shared Key according to the 
pre-shared key format you select. 
Enable Pre-Authenticatio
n You can mark this checkbox to enable 
Pre-authentication after selecting Enterprise 
(RADIUS) WPA 2 authentication mode 
Authentication RADIUS  
Sever If you use RADIUS Sever to ensure your 
security, you have to set up the parameters...

Access Control   
To restrict the Number of Access authentication of Stations, Set up the 
control list in this page. 
 
   Configuration  
Wireless Access 
Control Mode Click on the drop list to choose the access 
control mode. You may select “Allow listed” to 
allow those allowed MAC addresses or select 
“Deny Listed” to ban those MAC addresses from 
accessing to this device. 
MAC Address & 
Comment  To set up the Value of MAC Address & 
Comment; enter the MAC Address and 
Comment of station and click...