Alfa Router AIP-W610 User Manual

							
Denial of Service 
Denial of Service(DoS) allows users to prevent certain packets from accessing this 
router. This helps to improve the security and against the assault from hackers. 
To perform Denial of Service: 
1.  Mark the  “Enable DoS prevention”  checkbox. 
2.  Some packets allow users to specify a packet flow limit. Please fill in an 
allowed packet amount per second in those blanks first. 
3.  Select those packet types that you are going to block by marking the check 
boxes. You may also click the  “Select All” button to select all packet types 
or click  “ Clear All ” button to remove all selected packets. 
4.  Click the  “Apply Changes”  button to execute.   
46 
 
  
						

							
System Log 
This System Log page shows the information of the current activities on \
the router.   
To enable system log function: 
1.  Mark the “Enable Log” checkbox. 
2.  To see all information of the  system, select the “system all” 
checkbox. 
3.   To see wireless information only, select the “wireless” 
checkbox. 
To sent the log information to a certain note, select the 
“Enable Remote Log” checkbox and fill in the IP address in 
the “Log Server IP Address” box. 
4.  Click the “Apply Changes” button to activate 
 
You could also click the “Refresh” button to refresh the log information or 
click the “clear” button to clean the log table.   
47 
 
  
						

							
Upgrade Firmware 
To Upgrade Firmware,   
1.  Click “browse…” button to select the firmware you 
want to upgrade. STEPS 
2.   Click Upload to start the upgrade process. Please 
don’t close the WEB-browser and wait for process 
to complete. When Upgrade is completed, you 
can start to use the router.   
48 
 
 
  
						

							
Save and Reload Settings 
To save setting to file, click “Save...” button. 
To load setting from file, 
1. Click “Browse…” on the to select the file 
2.  Click upload to start the proce ss and wait for it to complete 
To reset setting to Default, click rese t to start the process and it will be 
completed till the status LED start blinking.   
 
Password 
To set up the Administrator Account in formation, enter the Username, New 
password, and reenter the password on the text box. Don’t forget to click the 
“Apply Changes” to save  the configuration. 
 
49 
 
  
						

							
Product Specifications 
 
 
Standard 
IEEE802.3, 10BASE-T 
IEEE802.3u, 100BASE-TX 
IEEE802.3x full duplex operation and flow control 
IEEE802.11b wireless LAN infrastructure 
IEEE802.11g wireless LAN infrastructure 
Interface 
1 * WAN port 
4 * 10/100 RJ-45 Fast Ethernet switching ports 
Antenna: 802.11b/g wireless reverse SMA detachable 
WAN Connection Ethernet 10/100 Mbps 
Cable Connections RJ-45 (10BASE-T): Category 3,4,5 UTP 
RJ-45 (100BASE-TX): Category 5 UTP 
Network Data Rate 802.11b: 1, 2, 5.5 and 11Mbps 
802.11g: 6, 9, 12, 18, 24, 36, 48, and 54Mbps 
Transmission Mode Auto-Negotiation (Full-duplex, Half-duplex) 
LED indications 
System: Power, Status 
Port (WAN): ACT/LINK 
Port (LAN): ACT/LINK 
Port(Wireless): ACT 
Security 64/128-bit WEP,   
WPA(TKIP with IEEE 802.1x), WPA2, AES 
Receiver Sensitivity 
54Mbps OFDM, 10%PER, -71dBm 
11Mbps CCK, 10%PER, -81dBm 
1Mbps BPSK, 10%PER, -92dBm 
Memory Flash : 2MB NOR type,    SDRAM : 16MB 
Transmit Power 16dBm~18dBm 
Range Coverage Indoor 35~100 meters   
Outdoor 100~300meters. 
Emission FCC CLASS B, CE, VCCI Class B 
Operating Temperature 00 ~ 400C (320 ~ 1040F) 
Operating Humidity 10% - 90% 
Power Supply External Power Adapter, 12VDC/ 1A 
Or choose from 4 LAN or 1 WAN Passive PoE support 
50