AllTrade Snapon 18Ga Crown Stapler 870017 User Manual

MODEL #870017
18 GAUGE 1-5/8 NARROW CROWN STAPLER
INSTRUCTION MANUAL
FOR CUSTOMER SERVICE
PARA EL SERVICIO
PARA EL CONSUMIDOR1-888-278-8092
Printed in Taiwan 
SNAP-ON
®IS A TRADEMARK LICENSED BY SNAP-ON
®CORP.,
U.S.A., WHICH DOES NOT MANUFACTURE OR 
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
©COPYRIGHT 2007 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
870017 – 18 Gauge 1-5/8 Stapler_Rev 9/6/07
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY,...

CONGRATULATIONS!
Thanks for choosing this product. Our aim is to provide you with the highest quality prod-
ucts, and we want you to be totally satisfied with your product and our Customer Service.
If any help or advice is needed, please contact us at 1-888-278-8092. When properly
cared for, this product will give you many years of satisfaction.
GENERAL SAFETY RULES
READ AND FOLLOW ALL INSTRUCTIONS. Failure to fol-
low all instructions in this manual may result in severe personal injury or death.
Keep...

IMPORTANT INFORMATION ABOUT THIS MANUAL
Improper maintenance and operation are responsible for the majority of accidents
involving air staplers. The largest portion of these could be prevented by recogniz-
ing the basic safety rules and precautions. Most accidents can be avoided if the
operator recognizes a potentially hazardous situation before it happens and by
observing appropriate safety rules and procedures as outlined in this manual.
Basic safety precautions are outlined in the SAFETYportion of...

Always use hearing protection to protect your ears against
hearing loss due to exhaust noise. Always wear proper safe-
ty glasses to prevent injuries to the eyes from fragments of
the work piece, defective staples or other debris caused by using the air sta-
pler.All safety glasses must have side shields and should conform to the
requirements of the American National Standards Institute (ANSI) z87.1. Failure
to comply with this warning could lead to serious or permanent damage to the
ears as well as...

COMPONENT INSTALLATION
Never use a non-relieving air coupler with the air stapler.
Always use couplers that release any built-up charge in the air stapler’s firing
mechanism. A non-relieving air coupler can allow the air stapler to discharge a
fastener while the tool is disconnected from the power source. Failure to com-
ply with this warning can result in serious or permanent injury or even death to
the operator or to bystanders.
When selecting an air compressor, it must comply with the requirements of...

OPERATION IN SINGLE SEQUENTIAL ACTUATION MODE
To select the Single Sequential Actuation Mode (see
Figure 1): 
1. Press and hold the red Actuation Selector embedded
in the trigger.
2. Rotate Actuation Selector down to the Single
Sequential Actuation (T).
3. Release Actuation Selector, ensuring locking tab is
fully seated in the slot.
Ensure selector has locked into position. Ensure 
actuation process is fully understood before attempting to use air stapler.
TO USE THE AIR STAPLER IN SINGLE
SEQUENTIAL...

To select Contact Sequential Actuation Mode (see Figure 2): 
1. Press and hold Actuation Selector embedded in the
trigger.
2. Rotate Actuation Selector up to the Contact
Sequential Actuation (TTT).
3. Release Actuation Selector, ensuring locking tab is
fully seated in the slot.
Ensure selector has locked into position. Ensure 
actuation process is fully understood before attempting to use air stapler.
TO USE THE AIR STAPLER IN CONTACT ACTUATION MODE:
1. Firmly grip air stapler handle.
2. Pull and hold...

6. Select Single Sequential Actuation Operation. Check for leaks. Without pulling
the trigger, press the work piece contact against the work piece. The tool
MUST NOT operate. Holding the tool away from the work piece, pull trigger
and hold for 5 seconds. The tool MUST NOT operate. Repeat steps several
times. Without pulling trigger, press stapler against work piece and pull trigger.
The tool MUST operate. Release trigger. Driver MUST move up.
7. Select Contact Actuation Operation. Holding stapler away...

OVERALL MAINTENANCE OF AIR STAPLER
Always disconnect the air hose from air stapler before
attempting any type of maintenance or visual inspection of tool.
Always visually inspect air stapler
before every use. Check on the overall
condition and for any loose screws.
Tighten any screws that have come
loose. See Figure 9.
Visually inspect the work piece contact
and trigger to ensure there is free
movement. See Figure 10.
When the tool is not going to be used
for an extended period, wipe off all
dust and...

PROBLEM POSSIBLE CAUSE SOLUTION
MANDATORY MAINTENANCE 
All maintenance and repairs should be performed by an
authorized repair facility. Call 1-888-278-8092 to obtain a list of repair facil-
ities in your area or to make arrangements to return the tool for service.
ACTION REASON OPERATION
TROUBLESHOOTING
Most minor problems can be resolved quickly and easily using the troubleshooting
table below. For problems that cannot be solved, contact Customer Service (toll
free) at 1-888-278-8092.
PROBLEM POSSIBLE...