AllTrade Snapon Round Head Framing Nailer 870010 User Manual

MODEL #870010
FOR CUSTOMER SERVICE
PARA EL SERVICIO
PARA EL CONSUMIDOR1-888-278-8092
Printed in Taiwan 
SNAP-ON
®IS A TRADEMARK LICENSED BY SNAP-ON
®CORP.,
U.S.A., WHICH DOES NOT MANUFACTURE OR 
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
©COPYRIGHT 2007 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
870010 – Round Head Air Nailer _Rev 10/4/07
ROUND HEAD FRAMING NAILER
INSTRUCTION MANUALTHIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION,...

CONGRATULATIONS!
Thanks for choosing this product. Our aim is to provide you with the highest quality prod-
ucts, and we want you to be totally satisfied with your product and our Customer Service.
If any help or advice is needed, please contact us at 1-888-278-8092. When properly
cared for, this product will give you many years of satisfaction.
GENERAL SAFETY RULES
READ AND FOLLOW ALL INSTRUCTIONS. Failure to fol-
low all instructions in this manual may result in severe personal injury or death.
Keep...

IMPORTANT INFORMATION ABOUT THIS MANUAL
Improper maintenance and operation are responsible for the majority of accidents
involving round head nailers. The largest portion of these could be prevented by rec-
ognizing the basic safety rules and precautions. Most accidents can be avoided if
the operator recognizes a potentially hazardous situation before it happens and by
observing appropriate safety rules and procedures as outlined in this manual.
Basic safety precautions are outlined in the SAFETYportion...

Do not connect round head nailer to an air source capable of gen-
erating more than 200 psi (14.06 kg/cm
2 G).Over-pressurizing the
round head nailer will result in bursting, abnormal operation or
breakage of the tool. Use only clean, dry, regulated compressed air
at levels specified on the tool. Failure to comply can cause severe injury or
death to the operator or bystanders.
Do not attempt to fasten the trigger in the “ON” position.This could lead to
an accidental discharge of the round head nailer. Do...

COMPONENT INSTALLATION
Never use a non-relieving air coupler with the round
head nailer.Always use couplers that release any built-up charge in the round
head nailer’s firing mechanism. A non-relieving air coupler can allow the round
head nailer to discharge a fastener while the tool is disconnected from the
power source. Failure to comply with this warning can result in serious or per-
manent injury or even death to the operator or to bystanders.
When selecting an air compressor, it must comply with the...

OPERATION IN SINGLE SEQUENTIAL ACTUATION MODE
To select the Single Sequential Actuation Mode (see
Figure 1): 
1. Press and hold the red Actuation Selector embedded
in the trigger.
2. Rotate Actuation Selector down to the Single
Sequential Actuation (T).
3. Release Actuation Selector, ensuring locking tab is
fully seated in the slot.
Ensure selector has locked into position. Ensure 
actuation process is fully understood before attempting to use round head
nailer.
TO USE THE ROUND HEAD NAILER IN SINGLE...

To select Contact Sequential Actuation Mode (see Figure 2): 
1. Press and hold Actuation Selector embedded in the
trigger.
2. Rotate Actuation Selector up to the Contact
Sequential Actuation (TTT).
3. Release Actuation Selector, ensuring locking tab is
fully seated in the slot.
Ensure selector has locked into position. Ensure 
actuation process is fully understood before attempting to use round head
nailer.
TO USE THE ROUND HEAD NAILER IN CONTACT ACTUATION MODE:
1. Firmly grip round head nailer handle....

6. Select Single Sequential Actuation Operation. Check for leaks. Without pulling
the trigger, press the work piece contact against the work piece. The tool
MUST NOT operate. Holding the tool away from the work piece, pull trigger
and hold for 5 seconds. The tool MUST NOT operate. Repeat steps several
times. Without pulling trigger, press nailer against work piece and pull trigger.
The tool MUST operate. Release trigger. Driver MUST move up.
7. Select Contact Actuation Operation. Holding nailer away from...

CLEARING JAMS
Typically, jams are caused when a fastener or a fastener fragment becomes wedged
between the driver blade and nail guide. Using the wrong fastener can also cause jams.
TO CLEAR A JAM:
1. Disconnect the air supply and
remove the fastener strip. Leave the
pusher assembly open.
2. Loosen hex screws from back of
magazine and pull magazine back.
See Figure 9.
3. Remove jammed fastener.
4. Slide magazine back in position and
refasten hex screws (Figure 10). MAINTENANCE
STORAGE OF NAILS
Always...

MANDATORY MAINTENANCE 
All maintenance and repairs should be performed by an
authorized repair facility. Call 1-888-278-8092 to obtain a list of repair facil-
ities in your area or to make arrangements to return the tool for service.
ACTION REASON OPERATION
TROUBLESHOOTING
Most minor problems can be resolved quickly and easily using the troubleshooting
table below. For problems that cannot be solved, contact Customer Service (toll
free) at 1-888-278-8092.
PROBLEM POSSIBLE CAUSE SOLUTION
Always visually...