Alpha Tool.Com.HK Limited Polisher VSP120 User Manual

Model No.:  VSP-120
Alpha® Variable
Speed Wet Polisher Instruction Manual
MANUAL
WARNING: To reduce the risk of injury, user must read and understand instruction manual!
103 Bauer Drive, Oakland, NJ 07436 • 800-648-7229 • Fax: 800-286-01 14
www.alpha-tools.com
Version 5  

ii
VSP-120 Overview ........................................................................\
...................... 3
  Specifications  ........................................................................\
................... 3
  Accessories ........................................................................\
...................... 4
Introduction  ........................................................................\
.................................. 5
  About Symbols...

1
VSP-120 OVErViEw
  SPECiFiCATiONS
Working Power Supply ......................................................Single-phase AC, 50/60 Hz
Voltage  ........................................................................\
......... 120V
Plug Type ........................................................................\
..... A (120V)
Amperage ........................................................................\
.... 7A
Wattage ........................................................................\...

2
ACCESSORIES
COMPONENTS:
1.    Side Handle (Part No. 210074)
2.    Wrench (Part No. 210073)
3.    Band Clamp (Part No. 210088)
4.    Splash Guard (Part No. 210089)
5.    Spare Set of Carbon Brushes (Part No. 210048)
Figure-2

  
  

3
iNTrODUCTiON
Thank you for purchasing the Alpha®  Wet Polisher.  Please read this instruction 
manual thoroughly to ensure safety and correct use of the polisher.  Keep this manual 
in a place where operators can access it easily whenever necessary. 
 ABOUT THE SYMBOLS
According  to  the  hazard  level,  all  safety  notes  in  this  manual  are  classified  into 
“DANGER”, “WARNING”, and “CAUTION”.
 DANGER!    Death or serious personal injury is imminent when   handling 
this polisher incorrectly....

4
  CAUTION
The  following  are  important  notes  for  products,  operation,  and  maintenance 
applicable to this polisher.
GENERAL SAFETY RULES
wOrK ArEA
•	   Keep your work area clean and well lit.   Cluttered benches and dark areas 
invite accidents.
•	  
Do not operate power tools in explosive atmospheres, such as in the 
presence	 of	flammable	 liquids,	gases,	or	dust.    Power  tools  may  create 
sparks which may ignite the dust or fumes.
•	 	 Keep	 bystanders,	 children,	and	visitors	 away	while...

5
•  
Dress	 properly.	 Do	not	 wear	 loose	 clothing	 or	jewelry.	 Contain long hair. 
Keep your hair, clothing, and gloves away from moving parts. Loose clothes, 
jewelry, or long hair can be caught in moving parts or drawn into air vents.
•	 	 Avoid	 accidental	 starting. Be sure switch is off before plugging in. Carrying 
tools  with  your  finger  on  the  switch  or  plugging  in  tools  that  have  the  switch 
on, invites accidents.
•    Remove	 adjusting 	keys	 or	wrenches	 before	turning 	the...

6
•  
Use	 only	 accessories	 that	are	recommended 	by	 the	 manufacturer	 for	your 	
model . Accessories that may be suitable for one tool, may become hazardous 
when used on another tool.
SErViCE
1.  	
Tool 	service	 must	be	performed 	only	 by	qualified 	repair	 personnel.  
Service  or  maintenance  performed  by  unqualified  personnel  could  result  in 
a risk of injury.
2.    When	 servicing	 a	tool,	 use	only	 identical	 replacement	 parts.  Follow 
instructions in the Maintenance section of this...

7
10. Do	not	 abuse	 cord.  Never carry the tool by the cord or yank it to disconnect 
it  from  the  receptacle.    Keep  cord  away  from  heat,  oil,  and  sharp  edges.  
Following this rule will reduce the risk of electric shock or fire.
11.  Make	 sure	your	 extension	 cord	is	in	 good	 condition.    When  using  an 
extension  cord,  be  sure  to  use  one  heavy  enough  to  carry  the  current  your 
product will draw. An undersized cord will cause a drop in line voltage resulting 
in loss of...

8
GrOUNDiNG iNSTrUCTiONS
This tool should be grounded while in use to protect the operator from electric shock. 
The tool is equipped with a three-conductor cord and three-prong grounding type 
plug to fit the proper grounding type receptacle.  The green (or green and yellow) 
conductor in the cord is the grounding wire. Never connect the green (or green and 
yellow) wire to a live terminal.
ADDiTiONAL PrECAUTiONS FOr USiNG THE VSP-120
In addition to the general safety notes described on the preceding...