Altinex CUSTOMIZABLE TABLE TOP WITH 2 POWER 3 SNAPIN CONNECTORS 1 DSUB 1 AUDIO TNP320C User Guide

							TNP328 INTERCONNECT BOX User’s Guide 
400-0611-002  
 
 
 
 
1 
 
Welcome!
We greatly appreciate your purchase of your TNP328 Series 
Tilt N Plug. We are sure you will find it reliable and simple to 
use. Superior performance for the right price, backed by solid 
technical and customer support is what ALTINEX has to offer.  
We are committed to providing Signal Management Solutions® 
to our customers for the most demanding audiovisual 
installations at competitive pricing and we welcome you to join 
the ranks of our many satisfied customers throughout the 
world.  
1. Precautions and Safety Warnings  
Please read this manual carefully before using your Tilt N 
Plug. Interconnect Box. Keep this manual handy for future 
reference. These safety instructions are to ensure the long life 
of your Tilt N Plug. and to prevent fire and shock hazards. 
Please read them carefully and heed all warnings.  
1.1 General  
 Unauthorized personnel shall not open the unit as there 
are high-voltage components inside. Qualified ALTINEX 
service personnel or their authorized representatives must 
perform all service.  
1.2 Installation Precautions  
 For best results, place the Tilt N Plug in a dry area away 
from dust. 
To prevent fire or shock, do not expose this unit to water 
or moisture. Do not place the unit in direct sunlight, near 
heaters or heat-radiating appliances, or near any liquid. 
Exposure to direct sunlight, smoke, or steam can harm 
internal components.  
 Handle carefully; dropping or jarring can damage the 
bezel.  
 Never place fingers inside the opening on either side of 
the unit. This action could cause injury due to sharp edges 
inside.  
 Do not place heavy objects on top of the Tilt N Plug. Do 
not use excessive force to push down on the top of the 
unit.  
 Disconnect the power cord to turn off the power. This 
supplies power to the socket on the pop-up panel. The 
power outlet should be installed near the equipment and 
be easily accessible.  
 We recommend using wall outlets with a Ground Fault 
Circuit Interrupter (GFCI) for maximum protection.  
 Install all cables according to the instructions found herein. 
Do not force or pull any cable that is attached to the Tilt N 
Plug.  
1.3 Cleaning  
 Surfaces should be cleaned with a dry cloth. Never use 
strong detergents or solvents such as alcohol or thinner. 
Do not use a wet cloth or water to clean the unit.  
 
2. Installation Procedures  
Step 1 Cut an opening into the table’s surface. Refer to the ALTINEX website at 
www.altinex.com for table cutout requirements.  
NOTE: The table can be 2.25 in (57 mm) or less in thickness. Always confirm dimensions before 
cutting to insure that specifications have not changed. 
Step 2 Insert the TNP328 into the table cutout.  
Step 3 Place the support brackets under the table and place them between the support mount 
grooves on the side of the unit. Attach the brackets to the groove at the desired height 
and secure them to the bottom of the table using the knurled table securing screws 
provided with the additional wing nuts for added tightening. See Diagram 3 for details.  
Step 4 To lower the unit, push on the top cover until it locks into place.  
Step 5 Secure all cables to the underside of the table using the cable clamps and screws 
included with the TNP. Pass the power cord from the bottom of the housing and attach it 
to the table separate from the signal cables. Leave enough slack in the service loop to 
allow for easy opening and closing, but not too much as to cause excess drooping of the service loop. 
Step 6 Connect the appropriate cables with the correct input connectors on the bottom of the unit.  
Step 7 Once you have applied power and connected the proper cables on the bottom of the unit you may raise the unit. To raise the 
unit into position, push down on the front of the top cover; the latching mechanism will then release, allowing the pneumatic 
spring to raise it into position.  
NOTE: It may be necessary to adjust the service loop of the cables for optimal performance.  
 
3. Limited Warranty/Return Policies  
Please see the ALTINEX website at www.altinex.com for details on warranty and return policies.     
						

							TNP328 User’s Guide 
400-0611-002  
 
 
 
 
2 
 
4. Technical Specification 
Specifications are subject to change. Please visit http://www.altinex.com for up-to-date specification 
 
Features/Description  
TNP328/320C* 
Pass-Through AC Power                      9ft. (3.0 m) 
 120 VAC,60 Hz, 12A NEMA Socket-Plug 
Agency Approval 
 UL/C-UL Listed File E254082 
Audio, Video, 
Communication 6 ft. (2 m) 
 Computer video 15-pin HD F-M (1) 
 Computer Audio 3.5mm F-M (1) 
 HDMI **HDMI F-M (1) 
 Network CAT-6 (RJ-45) F-M (1) 
Accessories Included 
Hardware -Mounting screws/brackets 
-Cable clamps/screws 
Table 1 TNP328 General Specifications 
 
 
Mechanical  
Max. Table Thickness 2.25 in (57 mm) 
Height, opened 6.4 in (163 mm) 
Width 5.7 in (145 mm) 
Depth 5.2 in (132 mm) 
Finish                   Standard: 
            Models ending in S: 
Matt Black Finish 
  Brushed Aluminum 
Weight (approx.) 2.75 lb. (1.25 kg) 
Shipping Weight 5.5 lb. (2.5 kg) 
T Operating 10C - 35C 
T Maximum 40C 
Humidity 90 non-condensing 
Table 2 TNP328 Mechanical Specifications *** 
 
 
Electrical 
 (Dual Outlet Panel) TNP328 
Power Rating  
 (pass-through AC power) 
120VAC,60Hz, 
Up to 12A total 
Table 3 TNP328 Electrical Specifications ***
* Models ending in “C” are customizable. 
Models ending in “S” have brushed aluminum finish. 
** HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in 
the United States and other countries. 
*** Dimensions and ratings include the customizable “C” models and “S” models. 
   
						

							TNP328 User’s Guide 
400-0611-002  
 
 
 
 
3 
 
5. The TNP328 Interconnect Box 
 Available in high quality matte black finish or clear brushed 
finish 
 Pre-configured, compact hybrid interconnect solution with 
HDMI and VGA interconnects or factory configured as a 
TNP320C 
 Dual AC sockets rated for up to 12A from one power cord 
 Simple, drop-in installation 
 Gas spring for smooth operation 
 UL listed 
 
 
 
 
 
 
The TNP328 is a compact interconnect solution designed for mounting into tables, podiums, or other furniture as part of a presentation 
system. Inputs are accessed by pushing down on the top cover allowing the unit to tilt open. The inputs are hidden by pressing down on 
the top cover until the latching mechanism engages. In the closed position, the top cover lays almost flush with the tabletop. This 
tabletop solution offers up to dual 12 Amps from the AC sockets with computer video/audio, HDMI and network pass through cables. 
The passive cables are 6ft and are bundled together for organized cable management. The power cable is split to deliver power to both 
outlets on the tabletop from one AC plug. The TNP328 is one of many solutions available in the TNP Jr product line that can be 
customized with many different connectivity options as a TNP320C. 
   
						

							TNP328 User’s Guide 
400-0611-002  
 
 
 
 
4 
 
6. Application Diagrams 
 
Diagram 1: Typical Setup and use of a TNP328 
   
Diagram 2: Front View  
						

							TNP328 User’s Guide 
400-0611-002  
 
 
 
 
5 
 
 
Diagram 3: Mounting the TNP328 
 
 
Diagram 4: Side Dimensions 
 
 
 
  
 
Diagram 5: Top Bezel Dimensions
 
    
						

							TNP328 User’s Guide 
400-0611-002  
 
 
 
 
6 
 
7. Operation 
7.1 Opening and Closing the Tilt N Plug 
The Tilt N Plug will open easily when the top is pressed down 
and then released. 
When the Tilt N Plug is not in use, simply press the top down 
until it is level with the surface of the table and then release.  The 
unit will remain hidden until needed again.  
7.2 Power/Signal Connections 
Connect external devices to the appropriate connector on the Tilt 
N Plug. Remember, the devices plugged into the AC power 
connectors should not draw more than 12A total. 
 
 
8. Troubleshooting Guide 
The Tilt N Plug supplied was carefully tested and no problems were detected. However, we would like to offer the following 
suggestions: 
TNP 
Symptom Resolution 
Signal quality is poor.  
1. Please make sure that the highest quality video and network cables are used. 
2. The TNP is a passive unit and does not alter signals in any way. If there is suspected problem 
with the signal quality, check the quality of the cables coming into and the TNP and connecting 
to the output of the TNP. If they are of low quality or improperly assembled, this will affect the 
overall quality of the signal. 
Damaged power cord 
1. Make sure that no cable or power cord is damaged or pinched.  
2. If there has been damage, do not use the Tilt N Plug. Please call the ALTINEX Customer 
Service Department at (714) 990-2300 to have the unit repaired. 
Unit raises too slowly 
1. If the unit does not rise into position correctly, check the service loops for the signal and power 
cords on the bottom of the unit. If the service loop is too small the cables will counteract the 
spring trying to raise the unit into position. 
Unit tilts up too fast 
1. If the unit rises into position too fast, check the service loops for the signal and power cords on 
the bottom of the unit. If the service loop is too large and the cables are putting upward pressure 
on the unit, the unit will tilt up too fast. 
Unit does not close all 
the way 
1. If the unit does not close flush with the bezel, check the service loops for the signal and power 
cords on the bottom of the unit. If the service loop is putting upward pressure in the unit, the unit 
will not be able to seat all the way down.