Aluratek 10 FT SHARETIME HDMI CABLE CB300101 User Guide

							ShareTime HDMI CABLE User’s Guide 
400-0619-001 1 
 
 
Welcome!
Everyone at Altinex greatly appreciates your purchase of the 
ShareTime Retractable HDMI cable. We are confident that you 
will find it to be reliable and simple to use. If you need support, 
please do not hesitate to call us at 714-990-2300.  
At Altinex, we are committed to developing unique and state of 
the art Signal Management Solutions® for demanding audiovisual 
installations. Welcome to the Altinex family of satisfied customers 
around the world! 
1. Precautions and Safety Warnings 
Please read the manual entirely before using your ShareTime 
Cable. You can download a full version of this manual at 
www.altinex.com. These safety instructions are to ensure the 
reliable operation of your ShareTime and to prevent fire and 
shock hazards. Please read carefully and heed all warnings. 
1.1 General 
 ShareTime Cable CB300-101 contains a micro USB 
programming connector that allows users to update the 
firmware of their unit when additional capabilities are 
developed by our engineering team. 
 ShareTime Cable CB300-101 contains a Li-Ion battery to 
provide the desired features and capabilities. 
1.2 Installation Precautions 
 To prevent fire or shock, do not expose this unit to water or 
moisture. Do not place the ShareTime Cable CB300-101 in 
direct sunlight, near heaters or heat-radiating appliances, or 
near any liquid. Exposure to direct sunlight, smoke, or steam 
can harm internal components. 
 Handle the unit with care; dropping or jarring can cause 
damage.     
 Do not abusively pull any cables that are attached to the 
CB300-101. Hold the CB300-101 firmly. 
1.3 Cleaning 
 Clean the ShareTime Cable CB300-101 with a dry cloth only. 
Never use strong detergents or solvents such as alcohol or 
thinner. Do not use a wet cloth or water to clean the 
connectors. 
1.4 FCC Notice 
 This device complies with Part 15 of the FCC Rules. 
Operation is subject to the following two conditions: (1) This 
device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference 
that may cause undesired operation. 
 This equipment has been tested and found to comply with the 
limits for a Class B digital device, pursuant to Part 2 of the 
FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference when the equipment is 
operated in a commercial environment. This equipment 
generates, uses, and can radiate radio frequency energy and, 
if not installed and used in accordance with the instructions 
found herein, may cause harmful interference to radio 
communications. Operation of this equipment in a residential 
area is likely to cause harmful interference in which case the 
user will be required to correct the interference at their 
expense. 
 Any changes or modifications to the unit not expressly 
approved by Altinex, Inc. could void the user’s authority to 
operate the equipment. 
 
 
 
 
2. Installation Procedures 
Step 1. Connect CB300-101 cable to a CEC capable display or switcher. 
Make sure CEC capability is enabled on the monitor. Some 
monitors have it defaulted to OFF. 
Step 2. Plug the ShareTime control side of CB300-101 into the laptop HDMI 
source. The LED flashes white briefly indicating a connection, then 
it flashes to indicate the input number and green to indicate that the 
video is on the display. If the TV is off, the ShareTime turns it on. 
Step 3. To configure the CB300-101 shutdown time, press the configuration 
button with a paper clip. 
Step 4. The various flashing colors represent the choices available. To 
select a time, wait for the desired color to start blinking and then 
press the button again. The LED turns solid on the selection.  
 
The CB300-101 is now ready for operation. Section 7 of this manual will explain how to setup configuration button user features and 
operational features through the circular touchpad just once. 
3. Warranty and Return Policies 
Please visit the Altinex website at www.altinex.com for details on warranty and return policies. In the case of a unit needing repair, 
please fill out the RMA (return material authorization) form located on the bottom left hand corner of the Altinex homepage. Once filled 
out, please email the form to [email protected].  
  
						

							CB300-101 User’s Guide 
400-0619-001 2 
 
4. Technical Specifications 
Specifications are subject to change due to continuous product developments. See www.altinex.com for up-to-date information. 
Features/Description Specification 
CB300-101 (10 ft., 3m) 
Output   
   Output Connectors HDMI M, Type A 
Input 
   Input Connectors HDMI M, Type A   
Compatibility 
   Signal Types HDMI 
   Signal resolution Standard HDMI resolutions 
Agency Approval 
FCC FCC class A 
Table 1. CB300-101 General 
Mechanical Specification 
Material (Housing) ABS Plastic 
Material (Flat cable) PVC 
Color Black 
  Height  0.58 in (15 mm) 
  Width 1.1 in (28 mm) 
  Depth 2.7 in (68 mm) 
Total Weight 0.85 lb. (0.39 kg) 
Flat Cable Length 10 ft. (3.05 m) 
T° Operating 10°C-35°C (50°F-95°F) 
T° Maximum 50°C (122°F) 
Humidity 90% non-condensing 
MTBF (tested.) 68,000 hrs. 
Table 2. CB300-101 Mechanical 
 
Electrical Specification 
Cable Gauge 36AWG 
Voltage Rating for Cable 30V 
Video Output Signal   
   Digital Signal Level Pass-through 
Power 
      5V DC 25 mW 
      Amplifier Built in for 1080p 
Table 3. CB300-101 Electrical 
Color Shutdown Time 
  Pink Never 
  Green 30 seconds 
  Blue 1 minute 
  Yellow 2 minutes 
  Cyan 5 minutes 
Table 4. CB300-101 LED pattern 
HDMI, the HDMI Logo, and High Definition Multimedia 
Interface are trademarks or registered trademarks of HDMI 
Licensing LLC in the United States and other countries. 
   
						

							CB300-101 User’s Guide 
400-0619-001 3 
 
5. About Your CB300-101 
 Easy collaborative control of display input switching  
 Automatically powers display ON and OFF (with CEC monitors) 
 HDMI compliant cable with internal boost 
 Compact design allows for easy plug & play 
 Use as many collaborative controllers as the number of HDMI inputs available 
 Compatible with all switchers and displays that comply with CEC commands 
 10 feet of high-quality flat cable  
 
The CB300-101 HDMI cable is a revolutionary HDMI collaborative display controller that allows cooperative display control using a high 
quality CEC controller and cable in a single assembly. Multiple CB300-101 HDMI cables allow multiple users to connect to one display 
and work together as they seamlessly switch between multiple sources, allowing for collaborative teamwork and cable organization. . 
The HDMI cable contains a built-in amplifier to maintain HDMI signal integrity. The CB300-101 has 10 ft. of high quality flat cable. 
In a typical application, users connect the flat HDMI cable to a monitor input and then connect the other end of the cable to the source. 
As soon as the ShareTime compact unit is plugged into an HDMI laptop output, a white light flashes briefly indicating a connection and 
then the LED flashes to indicate the input number of the TV. The LED then turns a solid green and the video is displayed on the TV.  
If the TV is in stand-by mode, the CB300-101 automatically turns it on and selects the proper input to assure that the image is properly 
displayed. Any number of ShareTime units can be used together to form a collaboration station with a single TV. The CB300-101 
constantly monitors its environment by default. When the last CB300-101 is disconnected from the HDMI source, the TV is turned off 
after the configured shutdown time.  
The CB300-101 can easily be used with any CEC compatible switchers to create a larger multiuser collaborative solution. Its small and 
flat cable design allows users to have an easy plug and play experience with instant collaboration. The launch of the UT260-041 and 
UT260-052 under table HDMI switchers, is a great addition to the overall collaborative experience.  
  
						

							CB300-101 User’s Guide 
400-0619-001 4 
 
6. Application Diagrams 
Diagram 1: Typical Setup  
   
						

							CB300-101 User’s Guide 
400-0619-001 5 
 
Diagram 2: CB300-101 Internal View 
 Diagram 3: CB300-101 Dimensions 
 
 
                       
						

							CB300-101 User’s Guide 
400-0619-001 6 
 
7. Operation 
Getting Started 
Plug the CEC controller with the circular touch button into a laptop HDMI output and the white LED flashes briefly. The CB300-101 
reads its input it number from the TV and then flashes the white LED to indicate the input number on the TV. The number of flashes 
corresponds to the input number (one flash indicates input one, two flashes indicate input two, and so forth).  
Note: If there is a problem reading the input, the LED flashes pink until successful. If the LED flashes for more than 10 
seconds, there is most likely a problem with the cable or the TV does not support CEC. 
After a few seconds, the LED turns a solid green and the video is displayed. If the CB300-101 is in standby mode, the CB300-101 LED 
immediately turns solid green when reconnected to the laptop. 
In order to manually turn off the TV, press and hold the circular touchpad. The LED flashes red after about 5 seconds and then 
becomes a solid red after another 5 seconds. While the LED is solid red, release the touchpad. At this point, the CB300-101 turns the 
TV off. To turn the TV back on, unplug the CB300-101 from the HDMI source and plug it back in. 
Unplugging the CB300-101 from the HDMI source starts the shutdown timer. A green LED flashes briefly every second of the 
countdown timer.  
Under its own power, the cable retract backs. For better longevity, it is recommended to guild the cable back. 
Note: If other CB300-101 units are active, the CB300-101 will shut down after a few seconds and there will be no power off 
from that CB300-101.  
A CB300-101 unit with a solid white LED indicates that a source is present but not displayed on the TV. Touch and release the 
touchpad to turn the LED green and displays the video on the TV. If another CB300-101 is displaying video on the TV, its LED turns 
white and its video is no longer displayed. 
Remote Control 
To shut down all CB300-101 units immediately, a remote control can be used to turn off the TV. After shutting down the TV, the 
CB300-101 units must be disconnected from the source and then reconnected to start the TV. The CB300-101 units also reflect the 
changes made when a user changes the input with a TV remote control. 
Note: If the CB300-101 units are in standby mode and a remote control is used, the units shut down immediately and there 
is no countdown to turn off the TV.  
Touchpad Features 
The circular touchpad has many features in addition to setting a source as active. Holding it down for a number of seconds allows 
different actions. As the LED cycles through different colors, release on the color described in the table below to select that option.  
For example, release when solid red turns off the TV.  
 
Action (times are  LED Upon Release 
Touch and Release Green* Set as active source 
Hold +3 sec Flash Red Return to normal operation 
Hold +2 sec Red Turn off TV 
Hold +8 sec Blue Enable TV detection and reset 
Hold +11 sec Yellow Disable TV detection and reset 
Hold +12 sec OFF Return to normal operation 
   * If configured for UT240-041 LED toggles active/inactive 
 
TV detection is a special feature and can be enabled or disabled. If enabled, the CEC controller periodically sends a signal to verify its 
input number. If a physical TV input change is detected, the CP300-101 automatically restarts using the new input. This should not be 
enabled unless there is a possibility the TV input cable might be moved during normal operation. Ideally, user do not have access to the 
TV input.  
						

							CB300-101 User’s Guide 
400-0619-001 7 
 
Configuration Button Setup 
Step 1. Make sure CEC capability and standby mode are enabled on the TV. Some TVs are defaulted to off. 
Step 2. Plug the CB300-101 into the laptop HDMI source. The LED flashes white to indicate the input number and green to indicate 
that the video is on the display. At this point, if the TV is off it turns on. 
Step 3. To configure the CB300-101 shutdown time, press the 
configuration button with a paper clip. 
Step 4. The various flashing colors represent the choices 
available. To select a time, wait for the desired color 
to start blinking and then press the button again. The 
LED turns solid on the selection.  
 
Configuration Button Features 
The configuration button has additional features using the 
press and hold option.  
A quick press and release has the LED indicate the current TV 
off time and allows for selection of a new TV off time.  
Press and hold until the LED turns blue and then release. The 
controller flash the version number of the internal firmware.  
Press and hold until the LED turns yellow and then release. 
The controller flashes the physical address of the collaborative controller within the system. For example, the physical address 1.2.0.0 
indicates that the collaborative controller is connected to input 2 of a HDMI interface that leads to the input 1 of the destination. Red 
flashes twice, blue flashes once, followed by quick flashes from green and yellow indicating zero.  
Press and hold until the LED turns cyan and then release. The LED flashes red or green indicating a failure or a pass of the internal 
CEC circuit inside the controller.  
Press and hold until the LED turns off and then release. If the LED turns off no selections were made. Release to return to normal 
operation with no changes.   
Action LED Upon Release 
Press and  Release ON The LED turns on to indicate the current TV off time and then the LED 
starts flashing to allow TV off time selection 
Hold 2 sec Blue Flash version number of times; the color and flashes vary by version 
Hold 4 sec Yellow 
Flash the physical address.  
Physical address = A.B.C.D. 
  
A = Blue B = Red C = Green D = Yellow 
Hold 6 sec Cyan Test the CEC in circuit. The LED flashes green 3 times indicating the 
circuit is working; red if there is a failure 
Hold 8 sec Red Set select plus de select operation then reset. ** 
Hold 10 sec Pink Set for active operation only; no de-select. ** 
Hold 12 sec OFF Return to normal operation; no changes. 
 ** Reset upon selection 
   
						

							CB300-101 User’s Guide 
400-0619-001 8 
 
Updating Firmware: 
1. Download and install the firmware update from www.altinex.com. 
2. Connect ShareTime to a PC using USB Type A to Micro USB. Once 
connected, the LED turns a solid color and then briefly turns off. The 
CB300-101 then flashes the appropriate number of times corresponding 
with a color to notify the user what version they currently have. 
 4 5 6 7 8 
 Blue Yellow Pink Cyan Green 
After this notification, the LED again briefly turns off and then becomes a 
solid color depending on the current firmware loaded. When the LED is a 
solid color, launch the update application. 
3. Select Program from the menu to run the application. 
4. After the update is complete, the LED flashes blue once more to indicate 
the NEW version number.  
5. Disconnect the USB cable from the CB300-101 and remove from the source, if connected. Wait 3 seconds and reconnect to 
the HMDI source. 
6. ShareTime is now ready with new firmware. 
  
						

							CB300-101 User’s Guide 
400-0619-001 9 
 
8. Troubleshooting Guide 
We have carefully tested the CB300-101 prior to it leaving the factory. However, we would like to offer suggestions for the following: 
CB300-101 
Symptom Resolution 
LED does not turn on Make sure that the unit is fully inserted into the HDMI connector and that the video output is set up 
to mirror the display of the laptop. 
Display does not turn 
ON 
1. Make sure the display has fully powered OFF. During power OFF, the sequence monitor may 
not understand the power ON command. 
2. Connect the CB300-101 first to the display, using an HDMI cable, and then connect CB300-101 
to your laptop. 
3. The display may not be CEC compatible.