American Audio Amplifier VLP Series User Manual

SP eakon  aSSeMBL y:  You  will  need  a  pair  of  neutrik  Speakon® n L4F c 
connectors.  You  will  also  need  high-quality  two  or  four  conductor  speaker 
cable, a pair of needle-nosed pliers and a 1.5-mm Allen key to assemble the 
Speakon connectors to your speaker wire. To assemble the  neutrik Speakon 
nL4Fc connector, complete the following steps:
1. Strip back 3/4-inch of the cable casing. Strip off 1/4-inch from the end of 
each of the conductors down to bare wire, and insert the brass...

©American Audio®  -  www.americanaudio.us  -  vLP Series™ Power Amplifier user manual  Page 12
operatIng MoDes: Always configure  your amplifier operating mode before beginning operation. if you want to change it dur-
ing performance. You must decrease the gain controls to their lowest levels to protect the speakers from any popping noise.
Stereo operation - Page 15/Figure  15 details  an  example  of  a  typical  stereo  set-up.  connect  your  inputs  into  channels  one  and 
two of the amplifier....

©American Audio®  -  www.americanaudio.us  -  vLP Series™ Power Amplifier user manual  Page 13
Mono  Subwoofer  - This  operation  is  similar  to  the  Stereo  Subwoofer  operation  but  in  mono.  When  running  subwoofers  it  is  usually 
recommended  to  run  them  in  mono  mode  to  achieve  a  cleaner  tighter  low  end.  This  operation  allows  you  to  run  several  subwoofers 
down to a minimum of 4 ohms. To avoid amplifier  overheating, never run the amplifier  below 8 ohms in this mode. Set...

©American Audio®  -  www.americanaudio.us  -  vLP Series™ Power Amplifier user manual  Page 14
put). Short Circuit Protection can usually be traced back to the signal output line (i.e. speaker line). check the line from the output ter-
minal of the amplifier to the speaker. if this line good, check the internal speaker connections and components. A short circuit will usu-
ally be traced to a bad cable or a bad speaker component and is rar ely traced to the amplifier itself.
thermal Protection - dual...

©American Audio®  -  www.americanaudio.us  -  vLP Series™ Power Amplifier user manual  Page 15
tYpICaL Mono brIDge set-Up
speaKers
8 oHm minimum
tYpICaL stereo oUtpUt ConneCtIons
speaKers
4 oHm minimum
speaKers
4 oHm minimum
use channel 1 inputs only (XLr or 1/4” Jacks)
X
use Speakon or Banana Jacks
use the two positive binding post 
termainals (red) for speaker output.
Figure 16
Figure 15 

The vLP  series  carries  a  one  year  limited  warranty.  We  recommend  you  fill  out  the  enclosed  warranty  card  to  validate  your  purchase.  All 
returned service items whether under warranty or not, must be freight pre-paid and accompany a  r.A. (return authorization) number. if the 
mixer is under warranty, you must provide a proof of purchase invoice. You may obtain a  r.A. number by contacting our customer support 
team on our toll free number. Please contact American Audio® customer...

VLP SerIeS SPeCS
Power supply: Ac 100v, 50/60Hz (Japan)
       Ac 110v, 60Hz (colombia)
       Ac 120v, 60Hz (u.S.A. and canada)
       Ac 127v, 60Hz (mexico)
       Ac 220v, 50Hz (chile and Argentina)
       Ac 220v, 60Hz (Philippines and Korea)
       Ac 230v, 50Hz (europe, new Zealand, South Africa, and Singapore)
       Ac 240v, 50Hz (Australia and u.K.)
modeL:                                          vLP 300                                             vLP 600...

©American Audio® World Headquarters:
6122 S. eastern Ave. Los Angeles, cA 90040 uSA
Tel: 323-582-3322  Fax: 323-725-6100
Web: www.AmericanAudio.us  e-mail: [email protected]
American dJ europe
Junostraat 2
6468 eW Kerkrade
netherlands
[email protected] / www.americandj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99