Analog Devices ICE100B Emulator Users Guide Rev 11

ICE-100B Emulator User’s Guide 1-9 Getting Started
vides emulator detection and JTAG I/O voltage selection. Use the ICE 
Test (part of the target configurator) to test the target. If any errors are 
encountered, the errors are reported immediately and the test ends. Each 
error message recommends a solution to the problem.
Refer to the online help for information about “target configurator”, 
“JTAG frequency”, and “ICE test”.
JTAG Frequency
The ICE-100B emulator supports JTAG clock operation at 5 MHz....

Troubleshooting and Warranty
1-10 ICE-100B Emulator User’s GuideAlso included in the EE-Note, complete warranty and return material 
authorization (RMA) information for emulators and EZ-KIT Lite prod-
ucts. In general, emulators less than one year old are within warranty, and 
repairs within that period are free of charge, but there are some limitations 
to this warranty coverage. For details, see the note.  

ICE-100B Emulator User’s Guide 2-1 
2 HARDWARE DESCRIPTION
This chapter describes the hardware design of the ICE-100B emulator and 
includes the following sections:
“LEDs” on page 2-1
Describes LEDs which inform you of the emulator’s status.
“Resetting the Target” on page 2-2
Describes how to reset the target.
“Custom Processor Boards” on page 2-3
Describes concerns regarding board lay out.
“Mechanical Specifications” on page 2-4 
Provides dimensional information.
LEDs
Three LEDs are located on the...

Resetting the Target
2-2 ICE-100B Emulator User’s Guide
Resetting the Target
When debugging remotely, the ability to reset the target can be very use-
ful. Reset the target via the software or by soldering a wire from the 
ICE-100B emulator to the target.
To solder a wire from the ICE-100B emulator to the target:
 Two solder points labeled RESET (reference designator 
P3) are 
located near the JTAG connector (
J1) and USB connector (P1) on 
the ICE-100B (see Figure 2-2).
 For an active low version (...

ICE-100B Emulator User’s Guide 2-3 Hardware Description
Figure 2-2 shows a portion of the ICE-100B emulator.
To reset the target via the software, use the Reset Target command.
 CCES users choose Target > Debug > Reset Target.
 VisualDSP++ users choose Debug > Reset Target.
The Reset Target command sends a reset pulse of the specified reset time 
duration to the target and opens the Reset Target Options dialog box. See 
the online help for the dialog box description. 
Custom Processor Boards
When...

Mechanical Specifications
2-4 ICE-100B Emulator User’s Guidedependant on the particular Analog Devices processor, as well as the delay 
characteristics of the custom processor board.
To ensure that the custom board’s JTAG interface is designed and laid out 
correctly, refer to Engineer-to-Engineer Note, Analog Devices JTAG Emu-
lation Technical Reference (EE-68), available from the Analog Devices Web 
site. This document is a technical reference for implementing the JTAG 
interface on your target....

ICE-100B Emulator User’s Guide 2-5 Hardware Description
Figure 2-3. ICE-100B Emulator Dimensions (in inches)
0.045”
0.070”
a
0.450”
0.300”
0.855”
0.785”2.990”
0.235”
0.310”
0.093”P3P13.3
1.8
JP1
JP2 2.5S TAT
PWR
P1
J1ICE-100B
MON
JP1
J1
RESET
PN: ADZS-ICE-100B
LED1
LED2 LED3
* = MAXIMUM COMPONENT HEIGHT *
* * 

Mechanical Specifications
2-6 ICE-100B Emulator User’s Guide 

ICE-100B Emulator User’s Guide 3-1 
3 SUPPORT
Analog Devices provides free technical support.      
Technical Support
For technical support, visit the Embedded Processing and DSP Technical 
Support page at:
  
http://www.analog.com/support.
From there you can:
 Access the EngineerZone DSP Support Forum where Analog 
Devices support team members and other designers exchange ideas 
and answer questions 
 Search our vast Knowledge Base containing application notes, data 
sheets, code examples, manuals, and...

Quality Assurance
3-2 ICE-100B Emulator User’s Guide
Quality Assurance
Analog Devices is committed to providing quality products and services. 
To continually provide this quality, please contact our Quality Assurance 
Department directly if you have any concerns at (603) 883-2430, Monday 
through Friday during normal business hours, or via e-mail at:
 
[email protected].
Our Quality Assurance manager will listen to your concerns and provide a 
timely and effective solution.