Anetsberger Brothers 14Inch Gas Fryer 14GS 14 standard Parts List User Manual

L22-371  Rev 0 2/13 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
IMPORTANT FOR FUTURE REFERENCE 
Please complete this information and retain this manual 
for the life of the equipment:
 
Model #:    __________________________  
Serial #:    __________________________  
Date Purchased:    ___________________  
 
Service & Parts Manual 
Covering the 
14GS Series 
 
ENGLISH  

 
L22-371  Rev 0 2/13 
 
 
 
 
 
 
 
 
TO THE PURCHASER 
Post, in a prominent location, the 
instructions to be followed in the event that 
an operator smells gas. Obtain this 
information from your local gas supplier. 
WARNING 
There is an open flame inside this appliance. 
The unit may get hot enough to set nearby 
materials on fire. Keep the area around the 
appliance free from combustibles. 
WARNING 
DO NOT
 supply the appliance with a gas 
that is not indicated on the data plate. If you 
need to...

 
L22-371  Rev 0 2/13 
  
 
 
TABLE OF CONTENTS 
 
1
 Leg Installation and Leveling -------------------------------------------------------------------------------------------------------------- 4 
1.1 Installation Clearances ------------------------------------------------------------------------------------------------------------------- 4 
1.2 Gas Connection --------------------------------------------------------------------------------------------------------------------------- 4 
1.3 Gas Connection...

 
4 
L22-371  Rev 0 2/13   
1  Leg Installation and Leveling 
This appliance must be installed with legs; it cannot be curb mounted. Curb mounting will seriously inhibit this 
appliances ability to effect proper combustion. 
WARNING 
This appliance must be installed with the legs provided by the manufacturer. 
 
WARNING 
Do not install legs or perform leveling procedure when unit is in operation or full of cooking medium. 
Serious injury could result. 
Required tools: 7/16 “ wrench and socket and a large...

 
5 
L22-371  Rev 0 2/13   
1.4  Fuel Supply Line Leak and Pressure Testing 
The fuel supply system must be tested before the appliance is used. If the fuel line is going to be tested at a 
pressure greater than ½ PISG (3.45 kPa), insure that that appliance is disconnected from the fuel line. If the 
fuel line is to be tested at a pressure equal to or less than ½ PSIG (3.45 kPa), the appliance can be connected 
during the test, but the unit’s gas valve must be shut. Test all gas line connections for...

 
6 
L22-371  Rev 0 2/13 
2.2  Main Burner System Adjustment 
For the main burners to operate the gas supply valve must be open and the thermostat must be turned on. For 
models with electric controls, the main power switch must be on. The main burners receive gas from the main 
gas supply through the thermostatically controlled valve. When the thermostat is turned up to a setting higher 
than the temperature of the oil in the tank, the gas control valve opens.  
The main burner pressure must be adjusted...

 
7 
L22-371  Rev 0 2/13 
CAUTION 
If the burners do not shut off at the LOWEST thermostat setting, the thermostat may be 
defective. Contact your local service company. 
 
2.4 Thermostat Calibration 
For Gas Operated and Electric Thermostats refer to the following procedure. 
 
a.  Remove the tube screen from the tank and place the tip of a digital thermometer in the 
shortening/oil approximately one inch above the temperature sensor. 
b.  Light the pilot as described in this manual, set the thermostat...

14GS-CS Series  
8 
L22-371  Rev 0 2/13   
3 Trouble Shooting 
Refer to this section to correct common problems that may be encountered during the course of normal 
operation. If applicable, a schematic is provided behind the panel containing the electrical components. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
NO YES
YES 
Appliance does not 
work. 
Will the 
pilot light? 
NO Is the gas 
supply 
valve 
o
pen?
NO Open the gas 
valve...

14GS-CS Series  
9 
L22-371  Rev 0 2/13 
3.1  Testing the Thermocouple: 
You will need a multimeter that can measure millivolts. Make sure that after holding a flame to the 
thermocouple it produces 30 mv. You can test for this by heating the thermocouple for about a minute and then 
place one lead on the copper casing of the thermocouple and the other lead on one of terminals of the hi limit 
wire connection. This is the easiest way to check the thermocouple but you are also going on the faith that the...

14GS-CS Series  
10 
L22-371  Rev 0 2/13 
 
4  14GS-Fryer Exploded View