Anetsberger Brothers 14Inch Gas Fryer 14GS 14 standard User Manual

        Anets Inc. 
Mailing Address: P.O. Box 501, Concord,NH  03302-0501 USA  Telephone:  603-225-6684 
                     Shipping Address: 10 Ferry Street, Concord, NH  03301 USA 
       www.anets.com 
 
 
 
FRYER 
Models 
14G, 14GS 
14GU, 14GSU,
 
MX-14EG, MX-14EGU 
Installation, 
User Operation, 
& 
Maintenance 
Manual 
 
DANGER 
Improper installation, adjustment, alteration, service, or maintenance can 
cause property damage, injury or death.  Read the installation, operating 
and maintenance...

DANGER 
Read these specifications, Code Requirements, Installation Requirements, Installation 
Instructions, and Operating Instructions very carefully.  Failure to follow the 
Instructions 
could cause the fryer to malfunction. A fryer malfunction can result in property damage, 
serious bodily injury, or death. 
 
 
 
CONTENTS 
Shipping Container Inspection ........................................................ 3 
Fryer Gas Supply Specifications ..................................................... 4...

SHlPPlNG CONTAlNER lNSPECTlON 
 
fryer carefully for damage.  Place the fryer in a 
safe location, if damage is noted, so that the freight 
damage claims adjuster can examine the fryer. 
3.  Save the shipping container for use during leg/ 
caster installation.  Refer to the Installation Instruc-
tions for that procedure. 
 
 
 
Models Covered By This Manual 
 
 
 
 
 
 
Standard Accessories furnished in the shipping carton for this fryer include: 
 
2 Fryer Baskets  1 Drain Valve Extension  1 Screen 
4...

FRYER GAS SUPPLY SPEClFlCATlONS 
Please make sure that Vour desired fr Ver location has gas supplV factors that 
are suitable for this product: 
 
 
 
 
 
 
 
*
 - 
BTU/Hr Rating is based on sea level operation.  For sites above 2000 feet, reduce this 
rating 4% for each 1000 feet above sea level. 
“W.C. = Inches, Water Column. 
Measure Supply Pressure when all other gas-powered equipment is operating. 
 
NOTE:  Using a flexible inlet line permits variation 
in the gas supply line location, both...

CODE REQUlREMENTS 
lMPORTANT: Read the Code Requirements 
and ALL installation instructions carefully, 
before starting the installation.  Contact the 
factory if any problems or questions arise. 
 
The fryer installation must conform with  local 
codes, or in the absence of local codes, with the 
National Fuel Gas Code, ANSI Z223.1 (latest 
edition); the Natural Gas Installation Code, CAN/ 
CGA-B149.1 (latest edition);  or the Propane Gas 
Installation Code, CAN/CGA-B149.2 (latest 
edition), as...

From the top of the flue on 
the fryer, allow a minimum 
of at least 10 inches verti-
cal clearance beneath a 
ventilating hood. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Figure 2.  Fryer Site Installation Requirements 
 
 
 
lNSTALLATlON 
Install the fryer in accordance with the preceding 
Code Requirements, as well as the following 
Installation Requirements. 
1. DO NOT install this fryer in a mobile home, 
trailer, or recreational vehicle.
 
2. 
Install this fryer in a location that allows it...

lNSTALLATlON 
LEG INSTALLATION 
INSTRUCTIONS 
1. Flatten the shipping carton (after unpacking the 
fryer and its parts and accessories) for surface 
protection during leg installation. 
2. Position the side of the fryer flat on the carton, 
exposing the fryer bottom mounting brackets 
for leg installation, as shown in Figure 3.
 
3. Place the leg mounting plate flush against the 
mounting bracket on the fryer bottom. 
4. Insert one mounting bolt through a flat 
washer and then through the proper 
hole in...

lNSTALLATlON lNSTRUCTlONS (Continued) 
CASTER INSTALLATION 
INSTRUCTIONS 
1. Flatten the shipping carton 
(after unpacking the fryer and 
its parts and accessories) for 
surface protection during leg 
installation.
 
2. Position the side of the fryer flat 
on the carton, exposing the 
fryer bottom mounting brackets 
for caster installation, as shown 
in Figure 4. 
3. Place the caster mounting plate 
flush against the mounting brac-
ket on the fryer bottom. 
4. Insert one mounting bolt 
through a...

lNSTALLATlON lNSTRUCTlONS (Continued) 
CASTER LEVELING INSTRUC-  CASTER LEVELING INSTRUC-
TIONS 
(Continued) TIONS (Continued) 
5
. Completely unscrew the bolts holding the 
caster mounting plate that requires leveling 
adjustment.  Retain the locking nuts for later 
reassembly.
 
6.  Reinsert each bolt through its flatwasher and 
the fryer mounting bracket; next, place a 
spacer of the required thickness on the bolt 
before inserting the bolt through its mounting 
hole on the caster mounting plate and...

GAS CONNECTlON 
Installing your ANETS  Fryer requires the fol-
lowing procedure, after its legs or casters are pro-
perly attached and  it is in its desired location. 
1.  Ensure that the gas control valve knob 
in the fryer has its OFF position next to the 
valve mark. 
2.  Ensure that the gas supply inlet line valve is 
closed (cross-wise to the pipe line direction). 
3.  Ensure that all fryer controls are set to OFF. 
4. Connect the ¾” gas supply line to the gas line 
adapter on the lower rear of the...