AOC 193fw User Manual

193FW+  
 
 
 
 
 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
TABLE OF CONTENTS 
  FOR YOUR SAFETY -------------------------------------------------- 1 
SAFETY PRECAUTIONS -------------------------------------- 2 
SPECIAL NOTES ON LCD MONITORS -------------------  3 
 
BEFORE YOU OPERATE THE MONITOR ---------------------  3 
FEATURES --------------------------------------------------------  3 
PACKING LIST ---------------------------------------------------  3...

 1
Before operating the monitor, please read this manual thoroughly. This 
manual should be retained for future reference. 
 
FCC Class B Radio Frequency Interference Statement  
WARNING: (FOR FCC CERTIFIED MODELS) 
 
NOTE: This equipment has been tested and found to comply with the limits for 
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful interference in 
a residential installation. This equipment generates,...

 2
PRECAUTIONS 
 
z  Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen 
sink, laundry tub, swimming pool or in a wet basement. 
z  Do not place the monitor on an unstable cart, stand, or table. If the monitor 
falls, it can injure a person and cause serious damage to the appliance. 
Use only a cart or stand recommended by the manufacturer or sold with 
the monitor. If you mount the monitor on a wall or shelf, use a mounting kit 
approved by the manufacturer and follow the kit...

 3 SPECIAL NOTES ON LCD MONITORS
 
 
The following symptoms are normal with LCD monitor and do not indicate a 
problem. 
  
NOTES  
•  Due to the nature of the fluorescent light, the screen may flicker during 
initial use. Turn off the Power Switch and then turn it on again to make 
sure the flicker disappears. 
•  You may find slightly uneven brightness on the screen depending on the 
desktop pattern you use. 
•  The LCD screen has effective pixels of 99.99% or more. It may include 
blemishes of 0.01%...

 4
 INSTALLATION INSTRUCTIONS    
 
SWIVEL BASE  
 
Install    Remove 
           
 
           
 
 
   
Figure 1     Installing and Removing the Swivel Base 
 
POWER CORD 
Power Source:
 
 
1.  Make sure that the power cord is the correct type required in your area. 
2.  This LCD monitor has an External universal power supply that allows 
operation in either 100/120V AC or 220/240V AC voltage area (No user 
adjustment is required.) 
3. Connect the AC-power cord into your LCD  monitor’s  External...

 5 CONTROLS AND CONNECTORS
      
VIDEO CABLE 
 
Connecting the D-Sub Cable: Connect one end of the 15-pin D-Sub cable to 
the back of the monitor and connect the other end to the computer’s D-Sub 
port. 
 
Connecting the Power Cord: Plug the AC-power cord into the External 
Adapter. Then plug  the  DC-jack power cable  into DC-IN Inlet. 
 
Connecting the DVI Cable:  Connect one end of the 24-pin DVI cable to the       
back of  the monitor and connect the other end to the computer’s DVI port....

 6 ADJUSTING THE VIEWING ANGLE 
 
•
  For optimal viewing it is recommended to look at the full face of the 
monitor, then adjust the monitor’s angle to your own preference. 
•  Hold the stand so you do not topple the monitor when you change the 
monitor’s angle. 
•  You are able to adjust the monitor’s angle from -5° to 20°. 
 
  
 
Figure 3 
 
 
NOTES    •  Do not touch the LCD screen when you change the angle. It may cause 
damage or break the LCD screen. 
•  Careful attention is required not to catch...

 7
OPERATING INSTRUCTIONS 
  GENERAL INSTRUCTIONS   
Press the power button to turn the monitor on or off. The other control buttons 
are located at front panel of the monitor (See Figure 4). By changing these 
settings, the picture can be adjusted to your personal preferences. 
•  The power cord should be connected. 
•  Connect the video cable from the monitor to the video card. 
•  Press the power button to turn on the monitor position. The power indicator 
will light up....

 8 FRONT PANEL CONTROL 
 
• Power Button:  
Press this button to switch ON/OFF of monitor’s power. 
 
• MENU / ENTER :  
Activate OSD menu when OSD is OFF or activate/de-activate adjustment 
function when OSD is ON or Exit OSD menu when in Brightness/ Contrast 
Adjust OSD status. 
 
• Luminance :  
Adjust contrast and brightness or function adjust. 
*Only adjustable at “STD” mode
 (see Brightness Preset below)  
• Brightness Preset: 
Switch between “STD”, “OFFICE” & “VIVID”. 
 
•  Auto Adjust button /...

 9  
HOW TO ADJUST A SETTING
 
   
1.  Press the MENU-button to activate the OSD window. 
2. Press 
 or  to navigate through the functions. Once the desired function 
is highlighted, press the MENU-button to activate it. If the function selected 
has a sub-menu, press 
 or  again to navigate through the sub-menu 
functions. Once the desired function is highlighted, press MENU-button to 
activate it.   
3. Press 
 or  to change the settings of the selected function.   
4.  To exit and save, select the...