AOC 2036sa User Manual

 41 
Windows Vista 
 
1. Click Start  and Control Panel. Then, double-click on Appearance and Personalization. 
    
  
2. Click Personalization and then Display Settings. 
   
 
3. Click Advanced Settings.... 
    
 
 

 42 
4. Click Properties in the Monitor tab. If the Properties button is deactivated, it means the configuration for your 
monitor is completed. The monitor can be used as is. 
If the message Windows needs... is displayed, as shown in the figure below, click Continue. 
   
 
5. Click Update Driver... in the Driver tab.  
   
 
6. Check the Browse my computer for driver software checkbox and click Let me pick from a list of device drivers 
on my computer. 
 
 
7. Click on the Have disk... button, then...

 43 
i-Menu 
 
Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on 
screen menus instead of the OSD button on the monitor. To complete installation, please follow the installation 
guide.  
 

 44 
Troubleshoot 
 
Problem & Question 
 
Possible Solutions 
 
 
Power LED Is Not ON 
 
Make sure the power button is ON and the Power Cord is properly connected 
to a grounded power outlet and to the monitor.  
 
 
 
 
 
 
 
 
 
 
No images on the screen 
 
Is the power cord connected properly? 
Check the power cord connection and power supply. 
Is the cable connected correctly? 
(Connected using the D-sub cable) 
Check the DB-15 cable connection.   
(Connected using the DVI cable) 
Check the DVI...

 45 
 
 
 
 
Monitor Is Stuck In Active 
Off-Mode 
 
The Computer Power Switch should be in the ON position.  
The Computer Video Card should be snugly fitted in its slot.  
Make sure the monitors video cable is properly connected to the computer.  
Inspect the monitors video cable and make sure no pin is bent.  
Make sure your computer is operational by hitting the CAPS LOCK key on 
the keyboard while observing the CAPS LOCK LED. The LED should either 
turn ON or OFF after hitting the CAPS LOCK key....

 46 
Specification 
General Specification 
LCD Panel  
model name 2036Sa 
Driving system  TFT Color LCD  
Viewable Image Size 50.8 cm diagonal 
Pixel pitch  0.2768mm(H) x 0.2768mm(V) 
Video  R, G, B Analog lnterface & Digital Interface 
Separate Sync.  H/V TTL 
Display Color  16.7M Colors  
Dot Clock  140MHz  
Resolution  
Horizontal scan range  30 kHz - 80 kHz 
Horizontal scan 
Size(Maximum)  442.8mm 
Vertical scan range  55 Hz - 75 Hz  
Vertical scan 
Size(Maximum)  249.075mm  
Optimal preset...

 47 
Weight (monitor only)  4.2kg 
Weight (with 
packaging)  5.5 kg 
Environmental  
Temperature:  Operating  0° to 40°  
Non-Operating  -20°to 60° 
Humidity:  Operating  10% to 85% (non-condensing)  
Non-Operating  5% to 80% (non-condensing)  
Altitude:  Operating  0~ 3000m (0~ 10000 ft )  
Non-Operating  0~ 5000m (0~ 15000 ft )  
 
 Preset Display Modes 
 
STAND RESOLUTION  
HORIZONTAL  
FREQUENCY(kHZ) 
VERTICAL  
FREQUENCY(Hz) 
VGA 640×480 @60Hz 31.469  59.940  
VGA 640×480 @67Hz  35.000  66.667  
VGA...

 48 
Pin Assignments 
 
 
 
Pin Number 15-Pin Side of the Signal Cable 
1 Video-Red 
2 Video-Green 
3 Video-Blue 
4 N.C. 
5 Detect Cable 
6 GND-R 
7 GND-G 
8 GND-B 
9 +5V 
10 Ground 
11 N.C. 
12 DDC-Serial data 
13 H-sync 
14 V-sync 
15 DDC-Serial clock 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 49 
Plug and Play 
Plug & Play DDC2B Feature 
 
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the 
monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional 
information about its display capabilities. 
 
The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over 
the DDC2B channel.
 

 50 
Regulation 
FCC Notice 
 
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) 
 
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference 
in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not 
installed and used in accordance with the...