AOC 2217pwc User Manual

    2217Pwc User Manual 
1. Preface About This Guide 
 
This guide describes the monitors features, setup,  and operation. lnformation in this document is subject to change w ithout notice. 
The sections are as follows: 
·  
Safety Instructions
: lists safety information.  
· 
Setup
: describes the initial setup process.  
· 
Using the Monitor
: gives an overview of how to use the monitor.  
· 
Drivers
: provides driver installation instructions for Win dows.  
· 
Technical Support 
: provides tips and...

2. Safety Introduction FCC Notice 
 
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) 
NOTE:  This equipment has been tested and found to comply  with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are d esigned to 
provide reasonable protection against harmful inter ference in a residential installation. This equipment generates, uses and can radiate radio frequency  energy, and if not 
installed and used in accordance...

Precautions
 
 WARNING: Use of controls, adjustments, or procedure
s other than those specified in this documentation may result in exposure to shock, electrical hazards , 
and/or mechanical hazards.  
Read and follow these precautions when connecting a nd using your computer monitor:  
PRECAUTIONS  · 
Do not use the monitor near water, e.g. near a bath tub, washbowl, kitchen sink, laundry tub, swimming  pool or in a wet basement.  
· 
Do not place the monitor on an unstable cart, stand , or table. If...

 
Adjusting Viewing Angle
 
· 
For optimal viewing it is recommended to look at th e full face of the monitor, then adjust the monitors angle to your own preference.  
· 
Hold the stand so you do not topple the monitor whe n you change the monitors angle.  
· 
You are able to adjust the monitors angle from -5° to 15°.  
 
   

NOTE: 
Do not touch the LCD screen when you change the ang le. It may cause damage or break the LCD screen.  
    
   
Attaching the Cables
 
Cable Connections On Back of Monitor and Computer  
 
1. Power  
2. Audio 
3. DVI 
4. Analog  
5. USB up   
6. USB down x 3  
Turn off your computer before performing the proced ure below. 
1.  Connect the power cable to the AC port on the ba ck of the monitor.  
2.  Connect one end of the 15-pin D-Sub cable to the  back of the monitor and connect the other end to...

   Attaching Wall Mounting Arm
 
Preparing to Install An Optional Wall Mounting Arm   
 
  

This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before t his procedure. Follow these steps: 
1.  Remove the base.   
2.  Follow the manufacturers instructions to assemb le the wall mounting arm.  
3.  Place the wall mounting arm onto the back of the  monitor. Line up the holes of the arm with the holes in the back of the monitor.  
4.  Insert the 4 screws into the holes and tighten.   
5.  Reconnect the cables.  Refer to the users manua l that came with the...

 
1  Eco Mode / Up   
2  Auto (Exit) / Left  
3  Menu / Right  
4  Volume   
5  Power on/off  
6  Camera   
7  microphone  
Operation Steps  
  
1) Press the MENU-button (
) to activate the OSD window.  
2) Press
 or 
to navigate through the functions. Once the desired  function is highlighted, press the MENU-button to activate sub-menu . Once the desired function is 
highlighted, press MENU-button to activate it.   
3) Press 
or 
to change the settings of the selected function. Pr ess 
or 
to select...

OSD Settings
 
· 
Press the MENU-button to activate the OSD window.  
· 
Press+ or - to navigate through the functions. Once  the desired function is highlighted, press the MENU-buttonto activate it.If the function selected has a sub-menu, 
press or again to navigate through the sub-menu fun ctions.Once the desired function is highlighted, press MENU-button to activate it.  
· 
Press+ or - to change the settings of the selected  function. To exit and save, select the exit function. If you want to adjust...

 
       DCC: Dynamic color control  
       ICM: Intelligent color management    
1) How to use Color Boost?   
  
YCM adjustment:  In addition to the basic R (red), G (green), B (bl ue) color adjustments, Color Boost has added Y (yel low), C (cyanine), and M (magenta) for more color 
fine-tuning options. YCM adjustments are in the thi rd icon labeled Color Temperature in the OSD menu . When adjusting YCM values, RGB values will also be changed 
automatically due to the color correlation between  RGB...