AOC 2436vwa User Manual

١  | Page  
 
AOC MONITOR 
USER`S GUIDE 
2436Vwa
 
 
 
SAFETY INTRODUCTION…………………………………………………………….2 
SETUP…………………………………………………………………………………….3 
ADJUSTING…………….…………………………………………………...………….  6                               
DRIVER INSTALLATION GUIDE…………………….….…………………………16                               
PRODUCT INFORMATION………………………………………………………….23                               
TROUBLESHOOT……...………………………………………………………….…..26    
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
 

٢  | Page  
 
SAFETY INTRODUCTION 
The following subsections describe notational conventions used in this document.  
Notes, Cautions, and Warnings 
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. 
These blocks are notes, cautions, and warnings, and they are used as follows: 
 NOTE: A NOTE indicates important information that helps you make better use of your computer 
system.  
 CAUTION: A CAUTION indicates either potential damage to...

٣  | Page  
 
 
 Clean the cabinet regularly with the cloth provided.  You can use soft-detergent to 
wipe out the stain, instead of strong-detergent which will cauterize the product 
cabinet.  
 
When cleaning, make sure no detergent is leaked into the product.   The 
cleaning cloth should not be too rough 
as it will scratch the screen surface 
 Please disconnect the power cord before cleaning the product.  
 
If the product is emitting a strange smell, sound or smoke, disconnect the power plug...

۴  | Page  
 
SETUP 
 
 
Not all signal cables (Analog, DVI, USB, Audio, and HDMI cables) will be provided for all countries and 
regions. Please check with the local dealer or AOC branch office for confirmation.  
Please setup or remove the base following the steps as below. 
 
 
 

۵  | Page  
 
Setup: 
 
Remove: 
 
 For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitors 
angle to your own preference.  
 Hold the stand so you will not topple the monitor when you change the monitors angle.  
 You are able to adjust the monitors angle from -5° to 20 °.  
 
NOTE: 
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.  
 
 

۶  | Page  
 
Cable Connections On Back of Monitor and Computer 
 
1. Power 
2. Analog (DB-15 VGA cable)  
3.Audio 
4.DVI 
To protect equipment, always turn off the PC and LCD monitor before connecting.  
1.  Connect the power cable to the AC port on the back of the monitor.  
2.  Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the 
computers D-Sub port.  
3.  Connect the audio cable to audio in port on the back of the monitor  
4.  (Optional – Requires a...

٧  | Page  
 
This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this 
procedure. Follow these steps: 
1.  Remove the base.  
2.  Follow the manufacturers instructions to assemble the wall mounting arm.  
3.  Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in 
the back of the monitor.  
4.  Insert the 4 screws into the holes and tighten.  
5.  Reconnect the cables.  Refer to the users manual that came...

٨  | Page  
 
4 Click Personalization  
 
 
5 Click Display Settings.  
 
6 Set the resolution SLIDE-BAR to 1920 by 1080.  
 
 
 
 
 
 
 

٩  | Page  
 
 
For Windows XP: 
1 Click START. 2 Click SETTINGS.3 Click CONTROL PANEL.  
 
 
4 Click Appearance and Themes. 
 
 
5 Double click DISPLAY.  
 
 
 
 
 

١٠  | Page  
 
6 Click SETTINGS. 
7 Set the resolution SLIDE-BAR to 1920 by 1080.  
 
For Windows ME/2000: 
1 Click START.  
2 Click SETTINGS.  
3 Click CONTROL PANEL.  
4 Double click DISPLAY.  
5 Click SETTINGS.  
6 Set the resolution SLIDE-BAR to 1920 by 1080.