AOC E2236vwa User Manual

							 
 41 
Windows Vista 
 
1. Click Start  and Control Panel. Then, double-click on Appearance and Personalization. 
    
  
2. Click Personalization and then Display Settings. 
   
 
3. Click Advanced Settings.... 
    
 
 
						

							 
 42 
4. Click Properties in the Monitor tab. If the Properties button is deactivated, it means the configuration for your 
monitor is completed. The monitor can be used as is. 
If the message Windows needs... is displayed, as shown in the figure below, click Continue. 
   
 
5. Click Update Driver... in the Driver tab.  
   
 
6. Check the Browse my computer for driver software checkbox and click Let me pick from a list of device drivers 
on my computer. 
 
 
7. Click on the Have disk... button, then click on the Browse... button and then select the appropriate drive 
F:\Driver (CD-ROM Drive).  
8. Select your monitor model and click on the Next button. 
9. Click Close → Close → OK → OK on the following screens displayed in sequence. 
 
						

							 
 43 
Windows 7 
1.Start Windows® 7 
 
2.Click on the Start button and then click on Control Panel. 
 
 
3. Click on the Display icon. 
 
 
4.Ckick on the “Change display settings” button.  
 
 
 
						

							 
 44 
5.Click the “Advanced Settings” button.  
 
 
6.Click the “Monitor” tab and then click the “Properties” button. 
 
 
7.Click the “Driver” tab.  
 
 
						

							 
 45 
8. Open the Update Driver Software-Generic PnP Monitor window by clicking on “Update Driver... “and then 
click the Browse my computer for driver software button.  
 
 
9. Select Let me pick from a list of device drivers on my computer.  
 
 
10. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory:  
X:\Driver\module name  (where X is the drive letter designator for the CD-ROM drive). 
 
  
 
						

							 
 46 
11. Select the xxx.inf file and click the “Open” button. Click the “OK” button.  
 
12. Select your monitor model and click the “Next” button. The files will be copied from the CD to your hard disk 
drive.  
 
13. Close all open windows and remove the CD.  
 
14. Restart the system. The system will automatically select the maximum refresh rate and corresponding Color 
Matching Profiles.  
 
 
 
						

							 
 47 
i-Menu 
 
Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on 
screen menus instead of the OSD button on the monitor. To complete installation, please follow the installation 
guide.  
 
						

							 
 48 
Troubleshoot 
 
Problem & Question 
 
Possible Solutions 
 
 
Power LED Is Not ON 
 
Make sure the power button is ON and the Power Cord is properly connected 
to a grounded power outlet and to the monitor.  
 
 
 
 
 
 
 
 
 
 
No images on the screen 
 
Is the power cord connected properly? 
Check the power cord connection and power supply. 
Is the cable connected correctly? 
(Connected using the D-sub cable) 
Check the DB-15 cable connection.   
(Connected using the DVI cable) 
Check the DVI cable connection.  
* DVI input is not available on every model. 
If the power is on, reboot the computer to see the initial screen (the login 
screen), which can be seen. 
If the initial screen (the login screen) appears, boot the computer in the 
applicable mode (the safe mode for Windows ME/XP/2000) and then change 
the frequency of the video card. 
(Refer to the Setting the Optimal Resolution) 
If the initial screen (the login screen) does not appear, contact the Service 
Center or your dealer. 
Can you see Input Not Supported on the screen? 
You can see this message when the signal from the video card exceeds the 
maximum resolution and frequency that the monitor can handle properly. 
Adjust the maximum resolution and frequency that the monitor can handle 
properly. 
Make sure the AOC Monitor Drivers are installed. 
 
Picture Is Fuzzy & Has 
Ghosting Shadowing Problem  
 
Adjust the Contrast and Brightness Controls.  
Press to auto adjust.  
Make sure you are not using an extension cable or switch box. We 
recommend plugging the monitor directly to the video card output connector 
on the back .  
 
Picture Bounces, Flickers Or 
Wave Pattern Appears In The 
Picture 
Move electrical devices that may cause electrical interference as far away 
from the monitor as possible.  
Use the maximum refresh rate your monitor is capable of at the resolution 
your are using.  
 
						

							 
 49 
 
 
 
 
Monitor Is Stuck In Active 
Off-Mode 
 
The Computer Power Switch should be in the ON position.  
The Computer Video Card should be snugly fitted in its slot.  
Make sure the monitors video cable is properly connected to the computer.  
Inspect the monitors video cable and make sure no pin is bent.  
Make sure your computer is operational by hitting the CAPS LOCK key on 
the keyboard while observing the CAPS LOCK LED. The LED should either 
turn ON or OFF after hitting the CAPS LOCK key.  
 
Missing one of the primary 
colors (RED, GREEN, or 
BLUE) 
 
Inspect the monitors video cable and make sure that no pin is damaged.  
Make sure the monitors video cable is properly connected to the computer.  
 
Screen image is not centered 
or sized properly 
 
Adjust H-Position and V-Position or press hot-key (AUTO).  
 
Picture has color defects 
(white does not look white) 
 
Adjust RGB color or select desired color temperature.  
 
Horizontal or vertical 
disturbances on the screen 
 
Use Windows 95/98/2000/ME/XP shut-down mode Adjust CLOCK and 
FOCUS.  
Press to auto-adjust.  
 
						

							 
 50 
Specification 
General Specification 
LCD Panel  
model name e2236Vwa 
Driving system  TFT Color LCD  
Viewable Image Size 54.7cm diagonal 
Pixel pitch  0.248mm(H) x 0.248mm(V) 
Video  R, G, B Analog lnterface & Digital Interface 
Separate Sync.  H/V TTL 
Display Color  16.7M Colors  
Dot Clock  148.5 MHz  
Resolution  
Horizontal scan 
range  30 kHz - 80 kHz 
Horizontal scan 
Size(Maximum)  476.64mm 
Vertical scan range  55 Hz - 75 Hz  
Vertical scan 
Size(Maximum)  268.11mm  
Optimal preset 
resolution  1920 x 1080 (60 Hz) 
Highest preset 
resolution  1920 x 1080 (60 Hz)  
Plug & Play  VESA DDC2B/CI  
Input Connector  D-Sub 15pin & DVI-D  
Input Video Signal  Analog: 0.7Vp-p(standard), 75 OHM, TMDS 
Power Source  100-240V~，50/60Hz 
Power Consumption  Typical < 42 W  
Standby < 1 W  
USB Downstream port 
(A type ) To USB device, loading < 100mA 
off timer 0~24hours Select timing to turn off the monitor. 
Speakers 2W x 2 
Physical 
Characteristics  
Connector Type  15-pin Mini D-Sub& DVI-D  
Signal Cable Type  Detachable  
Dimensions & 
Weight:  
Height (with base)  396.6 mm 
Width  531.3mm