AOC E2237fw User Manual

							
 11
Adjusting Viewing Angle 
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your 
own preference.   
Hold the stand so you will not topple the moni tor when you change the monitor's angle.   
You are able to adjust the monitor's angle from 4° to 14 °.   
 
 
NOTE: 
Do not touch the LCD screen when you change the a ngle. It may cause damage or break the LCD screen.
 
						

							
 
 12
Connecting the Monitor 
Cable Connections On Back of Monitor and Computer: 
 
  1. Power   
3. Analog (DB-15 VGA cable)  
   
4 .DVI  
   
To protect equipment, always turn off the PC and LCD monitor before connecting.   
 
1      Connect the power cable to the AC  port on the back of the monitor.   
2      Connect one end of the 15-pin D-Sub cable to the back of the monitor and conn ect the other end to the 
computer's D-Sub port.   
3      (Optional – Requires a video card with DVI port) - Connect one end of the DVI cable to the back of the monitor 
5    Turn on your monitor and computer.   
 
If your monitor displays an image, installation is complete. If it does not display an image, please refer 
Troubleshooting. 
123
45
2. Audio
5. HDMI
4     (Optional-Requires a video card with HDMI port)- Connect one end \
of the HDMI cable to the back of the monitor
and connect the other end to the computer’s DVI port.  
and connect the other end to the computers HDMI port.
 
						

							
 
 13
Wall Mounting 
Preparing to Install An Optional Wall Mounting Arm.   
 
This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this 
procedure. Follow these steps: 
 
1   Rem ove the base.  
2   F ollow the manufacturer's instructi ons to assemble the wall mounting arm.   
3      Place the wall mounting arm onto t he back of the monitor. Line up the holes of the arm with the holes in the 
back of the monitor.   
4      Insert the 4 screws into the holes and tighten.   
5      Reconnect the cables.    Refer to the user's m anual that came with the optional wall mounting arm for 
instructions on attaching it to the wall.   
 
Noted :    VESA mounting screw holes are not available for  all models, please check with the dealer or official 
department of AOC.   
 
Distance between the wall-mount holes :  75x 75 mm  
 
Screw specification for wall-mount : M4 x 10
 
						

							
 
 14
Adjusting 
Setting Optimal Resolution 
Windows Vista   
For Windows Vista: 
1 Click START.  
 
2 Click  CONTROL PANEL. 
 
 
3 Click  Appearance and Personalization. 
 
 
4 Click  Personalization   
 
 
 
						

							
 
 15
5 Click 
Display Settings.   
 
 
6 Set the resolution  SLIDE-BAR to 1920 by 1080.   
 
 
						

							
 
 16
Windows XP   
For Windows XP: 
1 Click START.   
 
 
2 Click  SETTINGS. 
 
3 Click  CONTROL PANEL.   
 
4 Click  Appearance and Themes.  
 
 
5 Double click DISPLAY.   
 
 
 
						

							
 
 17
6 Click 
SETTINGS. 
 
7 Set the resolution  SLIDE-BAR to 1920 by 1080.   
 
 
 
Windows ME/2000 
For Windows ME/2000: 
1 Click  START.   
2 Click  SETTINGS.   
3 Click  CONTROL PANEL.   
4 Double click  DISPLAY.  
5 Click  SETTINGS.   
6 Set the resolution  SLIDE-BAR to 1920 by 1080. 
1920        1080
 
						

							
 
 18
Hotkeys 
 
  Power Key 
Press the Power button continuously about 2 second to turn off the monitor. 
Eco Mode/DCR/i-care hot key   
Press the Eco key continuously to select the Eco m ode of brightness and DCR on when there is no OSD ( Eco 
mode hot key may not be available in all models).   
i-care can detect the intensity of surrounding lights and aut omatically adjusts the monitor brightness according to 
different light intensity 
 
Volume adjustment hot key 
When there is no OSD, press Volume (     ) to active volume adjustment\
  bar, press     or     to adjust volume. 
(Only for the models without speakers).   
 
4:3 or wide image ratio hot key 
When there is no OSD, press left hotkey continuously to c hange 4:3 or wide image ratio. (If the product screen size 
is 4:3 or input signal resolution is wide format, the hot key is disable to adjust.   ) 
 
Source hot key 
When the OSD is closed, press Source (or Auto/Source) butt on will be Source hot key function (Only for the models 
with dual or more inputs). Press Source button continuously to select the input source  showed in the message bar , 
press Menu/Enter button to change to the source selected.   
 
Auto configure hot key 
When the OSD is closed, press Auto/Source button continuously about 2 second to do auto configure (Only for the 
models with dual or more inputs).   
ECO(DCR)/i-care/up 
4:3 or Wide / Right Volume/Left
Source(Auto) / down 
◄
     ►
  ◄
   
 
 
						

							
 
 19
OSD Setting 
 
Basic and simple instruction on the control keys. 
 
 
 
 
1) Press  Menu (Power)  button to activate the OSD window. Press left, right, up, down  button to navigate through 
the functions. Once the desired  function is highlighted, press Menu (Power) button to activate submenu .   
 
2) In sub-menu, Press  up, down button to navigate through the functions.  Once the desired function is highlighted, 
press  left, right  button to change the setting. Press  Menu (Power) button to return to  superior menu.     
 
3) If you want to adjust any other function, repeat steps 1-2.   
 
4) To exit OSD windows, select “ exit” icon on main OSD, then press  Menu (Power) button .   
 
5)  OSD Lock Function:  To lock the OSD, press and hold the  Left button while the monitor is off and then press 
power  button to turn the monitor on. To  un-lock the OSD, press and hold the  Left button while the monitor is off and 
then press  power button to turn the monitor on. 
 
 
Notes:  
1)If the product has only one signal input, the it em of "Input Select" is disable to adjust. 
2)If the product screen size is 4:3 or input signal resolution  is wide format, the item of "Image Ratio" is disalbe to 
adjust.    
3)One of DCR, Color Boost, and Picture Boost functions is ac tive, the other two function is turned off accordingly. 
 
						

							
 
 20
Luminance 
Press   (Menu) to display menu. 
Press  (Left/Right/Up/Down) to  select 
 (Luminance),and press  to  enter. 
Press   (Up/Down) to select submenu, 
and press 
 (Lef t /Right) to adjust. 
Press  to  exit.