AOC Le24h138 User Manual

							11
Buttons located at the right side of the TV will operate the same as the\
se buttons on the remote control. 
 
M T SC C
PRE CH
Display
EPGWide
Add Fav
COMP
F a vM U/ E x i tE N
Buttondescription
POWER Press to turn on/off the TV.
TV 
Press to choose TV source mode. 
 AV Press to choose CVBS source mode.
COMP Press to choose Component source mode.
HDMI/PC Press repeatedly to choose HDMI or PC source mode.
PR
0-9  Press to enter TV channel number to select channel. 
 
PRE CHPRE CH Press to display the previous channel or source.
VOL +/- Press + or - to adjust the volume.
SOURCE The Source List should be activated and show on OSD. 
MUTE Switch the sound ON/OFF.
CH +/- Press + or - to browse through the TV channels.
 /  /  / 1. Press button to navigate OSD menu2. Cursor right key perform confirmation as well as precede next level o\
f OSD3. Can use cursor left to return previous level
OK 1. Press button to activate the setting/selection of OSD
2. Press to return previous level.
M U
/ E x i tE NMENU/EXIT
1. Press to activate OSD menu and back to previous level of OSD
2. Exit OSD 
DisplayDISPLAY Press to show the information about the input source, TV channel, displa\
y 
resolution.
Add FavAdd Fav No support for this product.
F a vFAV Channel No support for this product.
EPGEPG
No support for this product.
Play/Pause No support for this product.
StopNo support for this product.
WideWIDE Press to choose the display aspect.
Photo No support for this product.
Freeze No support for this product.
M T SMTS*Press to activate the NTSC TV sounds, such as: Stereo, SAP** or Mono 
tone.
SLEEP***Press to set sleep timer,setting a mount of time before your TV turn off\
 
automatically.
PICTURE Press to choose the Picture Mode.
AUDIO Press to choose the Audio Mode.
V-Chip No support for this product.
C CCCPress repeatedly to select closed caption type as CC Off, CC On or CC 
On when Mute.
- Press to enter 1~3 digital number of TV channel.
* multichannel Television Sound (mTS)The broadcasting standard, which allows stereo sounds to be transmitted \
with the TV picture.** Second audio program (Sap)Another or additional audio channel provided for in the Multichannel Tel\
evision Sound (MTS) broadcast standard. A monaural sound track included within 
the recorded or video signal (usually containing a second language tran\
slation for the displayed program).
*** SleepYou can set a time period for which the TV will be turned off automatica\
lly.
COMP
 
English
  
						

							12
Set-Up 
Inserting Batteries into the remote control 
Insert two size AAA batteries (supplied) to the diagram inside the bat\
tery compartment of the remote control. 
attaching the Base
ImporTanT: The Base of the AOC TV must be assembled prior to usage.
1.
 Place the TV set facing down on a soft and flat surface (blanket, foam,\
 cloth, etc.) to prevent any 
damage to TV set.   
2.
 Carefully align and insert the Base to the TV.
3.
 Gently push the Base towards the TV, and then fasten the base with M3 screws . 
4.
 Please refer to the “Important Usage instructions” in the above.
Wall-mounting 
Please install on a wall by using a Wall-Mount Bracket (sold separately\
). Before mounting the TV on a wall, the Table-Top Stand must be 
removed from the TV.  Follow the simple steps below to remove the Table-\
Top Stand:
1.
 Disconnect all the cables from the TV.
2.
 Gently lay the TV, face down, onto a level and stable surface covered wi\
th a thick and soft cloth. Make sure the Table-Top Stand is hanging 
over the edge. 
3.
 Remove the screws as shown in the illustration for your model and pull t\
he Table-Top Stand out. 
4.
 Do not remove any other screws from the TV. 
5.
 Do not remove the Table-Top Stand for any reason other than to Wall-Moun\
t the TV. 
6.
 Be sure to store the removed screws and Table-Top Stand in a safe place \
until you are ready to reattach the Table-Top Stand. Keep the 
screws away from small children. 
7.
 For bracket installation, refer to the instruction guide provided by the Wall-Mount Bracket model for your TV. Sufficient expertise is required in 
installing this TV, especially to determine the strength of the wall for\
 withstanding the TV’s weight. 
8.
 For product protection and safety reasons, AOC strongly recommends that \
you use the Wall-Mount Bracket model designed for your TV and 
the Wall-Mounting of your TV should be performed by AOC dealer or licens\
ed contractor. 
Note:  100 mm x 100 mm (22'') and  75mm x 75mm (24'') wall mount bracket & M4 screws (Screws length: 10mm and pitch: 0.7mm) \
are  not included. Please contact your local distributor.
1 23

English  
						

							13
English
Connecting TV 
Cable System or VHF/UHF Antenna System 
You can enjoy standard-definition and high-definition digital programmin\
g (if available in your area), along with standard-definition analog 
programming.
This TV is capable of receiving unscrambled digital programming for both\
 cable and external VHF/UHF antenna. 
It is strongly recommended that you connect the antenna/cable input usin\
g a 75-ohm coaxial cable to receive optimum picture quality. A 300-ohm 
twin lead cable can be easily affected by radio frequency interference, \
resulting in signal degradation. 
TV
TV
TUNER
High Definition Interface
You can enjoy high-definition programming by subscribing to a high-defin\
ition cable service or a high-definition satellite service. For the best 
possible picture, make sure you connect this equipment to your TV via th\
e HDMI or component video (with audio) input on the back of your TV. 
HDMI Connection
HDMIHDMI
HDMI
HDMI
HD Multimedia Interface
HDMI IN
If the equipment has a DVI jack and not an HDMI jack, connect the DVI ja\
ck to the HDMI IN (with DVI-to-HDMI cable or adapter) jack and 
connect the audio jack to the PC AUDIO IN jacks.
Component Signal Connection
Y Pb Pr
Component Video Input
Component INL R Y Pb PrL R Y Pb Pr
Audio
  
						

							14
English
Composite Signal Connection
AV
AV IN
CVBS
CVBS
CVBS
PC Connection
Use the TV as a monitor for your PC shown below with the HD15 to HD15 co\
nnection. This TV can also be connected to a PC with DVI or HDMI 
output. (Refer to the separate Quick Setup Guide.)
PC
VGA IN
 Connect the PC IN jack to the PC using the HD15- HD15 cable with ferrite\
 core (analog RGB) and audio cable.
 If the PC is connected to the TV and no signal has been input from the P\
C for more than 30 seconds, the TV enters the standby mode 
automatically.
 
						

							15
pC Input Signal reference Chart 
After connecting the PC to the TV, set the output signal from the PC according to the chart below for 22”\
 24” TV.
Standardresolutionhorizontal(kHz)frequency(Hz)
VESA 640 x 480 31.46959.94
VESA 800 x 600 35.156 56.250
VESA 800 x 600 37.87960.317
VESA 1024 x 768 48.36360.004
VESA 1360 x 768 47.7259.799
WXGA+ 1440 x 900 55.93559.887
WSXGA 1680 x 1050 64.67459.884
FHD 1920 x 1080 67.560
Video Input Signal reference Chart 
After connecting the videol input to the TV, set the output signal from the video input according to the chart below \
for 22” 24” TV.
presetting Video mode
Standard 
resolution horizontal (khz)  Vertical (hz) 
SD480i 15.734 60
SD 480P 31.5 60
HD 720P 4560
HD 1080i 33.75 60
FHD 1080p 67.5 60
Standard definition Interface
You can also enjoy traditional program by using a DVD player or VCR Play\
er. Connect this equipment to your TV via the Composite Input or
S-Video Input on the back of your TV.
Refer to the Quick Setup Guide (supplied) when connecting other equipm\
ent to your TV.
English
  
						

							16
USIng aoC TV
Turning the TV on and off
You can turn on the TV by using power switch button on the TV set or on \
the remote controller.
Power Button
English
  
						

							17
language Setting
1M U/ E x i tE NPress menU/exIT to call out MENU.
2
Press ▲/▼ to select “Feature”  , and press oK.
3
Press ▲/▼ to select "Menu Language", and press OK.
4
Press ◄/► to adjust.
5
M U / E x i tE NPress menU/exIT to exit.
Move Select Exit
Feature
Menu language
Menu timeout
Super contrastSleep timer
DCR
Closed caption English
20S
Off
Off
Off
Off
Analog caption
Reset all Off
No
B/L Control
100
English
    
						

							18
Viewing mode Selection
4:3 mode
Suitable for viewing conventional 4:3 programs in 
their normal format.
Zoom1 mode
Use these aspect modes to zoom in and to reduce 
the black bars.
16:9 mode
The original content in this mode has to fill the 
entire screen of the display.
Zoom2 mode
Use these aspect modes to zoom in and to reduce 
the black bars.
English
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
  
						

							19
Switching Input Source
On AOC TV, you can choose signal source on the remote control directly, or press Source to choose the signal source on the display menu.
1.
 When choosing signal source on the remote control directly: Press the following keys to switch input source.
 
M T SC C
PRE CH
Display
EPGWide
Add Fav
COMP
F a vM U/ E x i tE N
COMP
2. When using Source key to choose signal source:
 
M T S
C C
PRE CH
Display
EPGWide
Add Fav
COMP
F a vM U/ E x i tE N
1Press Source to call out source menu.
2
Press ▲/▼ to select input source: TV, CVBS, YPbPr, HDMI, VGA.
3
Press oK to enter. 
TV
CVBS
YPbPr
HDMI
VGA
English
  
						

							20
oSd manual Setting 
Channel Search 
This setting is only available in TV mode.
1M U/ E x i tE NPress MENU/EXIT to call out MENU.
2
Press ▲/▼ to select “Channel ”  , and press OK.
3
Press ▲/▼ to select "Tuning mode", and press OK. Select the mode of TV signal as Cable or Air.
4 Press ▲/▼ to select 
"System standard", and press  OK. Set as NTSC-M, Auto, PAL-M or PAL-N. Advise please do not change 
this item after auto search action.
5 Press ▲/▼ to select 
"Auto Search", and press OK.
6 Press MENU/EXIT to exit.
The submenu of Channel shows as below:
Channel Setting Itemsdescription
Program No. Shows the current channel number.
Tuning mode Select the mode of TV signal as Cable or Air.
System standard Can set as NTSC-M, Auto, PAL-M or PAL-N . 
Note: Please do not change this item after auto search action.
Auto search Select  “Auto  Search”  to  search  all  signaled  channel;  when  the  searching  is  complete,  it  stays  at  the  first  channel  with 
signal  and  all  channels  that  have  been  located  are  stored.  If  you  would  like  to 
stop  “Auto  Search”  during  the  process, 
simply by pressing the MENU/EXIT button.
Fine tuning Fine tunes the frequency of current channel.
AFC "AFC" can be set to ON or OFF. Set to ON, the TV will search signal automatically; when there is any offset in the signal, 
will automatically adjust the channel to the correct frequency.
 
Skip"Skip" can be set to ON or OFF. When it is set to ON, a channel can be skipped by pressing the switching button on the 
remote control or on the front panel. 
M U
/ E x i tE N
Move Select Exit
Channel
Tuning modeSystem standard
Fine tuning Auto search
AFC
Skip Program No. Cable
NTSC-M
0
On
Off 3
English