Apple ibook g4 14 inch mid 2005 User Manual

 
iBook G4 (14-inch Mid 2005) Take Apart -   
20
 
 Memory Card 
Procedure
 
1. Locate the installed memory card and brackets that secure the card on both sides. 
2. Carefully spread the brackets away from the notches in the card until the card  releases on each side. 
3. Holding the card by the top corners, pull the card up and out of the memory slot. 

 
21 -   
iBook G4 (14-inch Mid 2005) Take Apart  Memory Card
4. Align the notch in the replacement memory card with the small tab in the memory slot. 
Hold the card at a 30-degree angle, then push the card into the slot until it is  firmly 
seated.  
Note:   
If you feel resistance when inserting the card, try pushing one side at \
a time.
5. Gently push the top of the card down until the brackets snap onto both sides of the  memory card to lock it into place.  
Warning:  
   
Apply gentle pressure to...

 
iBook G4 (14-inch Mid 2005) Take Apart -   
22
 
 Bottom Case 
Bottom Case
 
Tools
 
• Soft cloth
• Torx T8 screwdriver or 2.0-mm hex driver
• Black stick (or other nonconductive nylon or plastic tool)
• #0 Phillips screwdriver
• Jeweler’s flat-blade screwdriver 
Part Location
Preliminary Steps
 
Before you begin, remove the battery.  

 
23 -   
iBook G4 (14-inch Mid 2005) Take Apart  Bottom Case 
Procedure
 
1. Place the computer upside down on a soft cloth.
2. Using a pin, pry up the three rubber feet from the metal sockets.  
Important:  
 When reassembling the computer, do not reuse the feet. Install three ne\
w 
rubber feet. 
3. Remove the three identical Phillips screws from the metal sockets.
4. Use a black stick to lift out the metal sockets.  
Note: 
   
When reassembling the computer, note that the metal sockets are keyed....

 
iBook G4 (14-inch Mid 2005) Take Apart -   
24
 
 Bottom Case 5.
 
Important:  
 To avoid damaging the case, be careful that the screwdriver tip does no\
t 
slip out of the screw head during removal. Remove the three screws.
6. Remove the two identical 4.5-mm long Phillips screws next to the battery connector. 

 
25 -   
iBook G4 (14-inch Mid 2005) Take Apart  Bottom Case
7. Note the locations of the slots on the bottom case pictured below. The computer frame 
has tabs that  fit into slots within the bottom case (six tabs in front; two on each side; 
three in back). When using a black stick to pry off the bottom case, it helps to know 
where the slots are as you free the tabs from the slots.
8. Starting at the battery compartment, use a black stick to carefully pry up the bottom  case from the computer. 
9....

 
iBook G4 (14-inch Mid 2005) Take Apart -   
26
 
 Bottom Case 10. Open the computer and place it on its side. Carefully work the black stick around the 
corners of the bottom case. 
The bottom case fits snugly. Use moderate force to remove the tabs from \
the slots. 

 
27 -   
iBook G4 (14-inch Mid 2005) Take Apart  Bottom Case
11. In the battery compartment, lift up the corner of the bottom case, and use a black stick 
or jeweler’s  flat-blade screwdriver to gently pry up the slot from the inner tabs on the 
frame. 

 
iBook G4 (14-inch Mid 2005) Take Apart -   
28  
 Bottom Case 12.
 
Note:  
 For this procedure, a black stick works best.
Loosen the tabs from the slot load area last. 
Pull up on the port side of the bottom case.
Placing the black stick nearly parallel to the slot drive opening, caref\
ully free the case 
from the remaining tabs at the slot drive side of the computer.  
Note: 
 When reassembling the computer, be careful not to pinch any cables as 
you press the bottom case back onto the computer....

 
29 -   
iBook G4 (14-inch Mid 2005) Take Apart  Bottom Case
13. If you are replacing any additional parts at this time, remove the two springs from the 
battery compartment so they do not fall out and get lost.  
Note: 
   
When reassembling the computer, make sure that the two springs in the 
battery compartment are in place before installing the bottom case. Each\
 spring has 
a plastic cap on one end. The cap should fit securely on the spring, and\
 the curved 
side of the cap should be positioned...