Apple power mac g4 cube User Manual

 
© 2002 Apple Computer, Inc. All rights reserved. 
ð
 
  
Service Source
Power Mac G4 Cube
 
Updated June 2, 2003 

 
© 2002 Apple Computer, Inc. All rights reserved. 
ð
 
  
Service Source
Take Apart
 
Power Mac G4 Cube 

 
Power Mac G4 Cube Take Apart -   
1  
 General Instructions 
General Instructions
 
Tools
 
The following tools are recommended for the Take Apart procedures:
¥ ESD wriststrap and mat
¥ Flat -blade screwdriver
¥ Magnetized Phillips screwdriver
¥ Torx T8 screwdriver
¥ Torx T10 screwdriver
¥ Pliers
¥ JewelerÕs Phillips screwdriver
¥ Black stick (or other nonconductive plastic or nylon tool)  
Note:  
 To organize the screws you remove from the assembly, use a tray with divided 
compartments (such as a...

 
2 -  
Power Mac G4 Cube Take Apart
 Computer Enclosure 
Computer Enclosure
 
Tools
 
No tools are required for this procedure. 
Preliminary Steps
 
Before you begin, turn off the computer. 
Procedure
 
Warning: Always turn off the computer before opening it to avoid damaging its 
internal components.  
1. Place the computer on a clean, ßat surface.
2. Shut down the computer, and wait Þve minutes for the computerÕs internal components 
to cool down.
3. Unplug all cables from the computer except the...

 
Power Mac G4 Cube Take Apart -   
3  
 Computer Enclosure 
Important:  
 To avoid electrostatic discharge, always ground yourself by 
touching the bare metal before you touch any parts or install any components 
inside the computer. To avoid static electricity building back up in your body, 
do not walk around the room until you have completed the installation and 
closed the computer.   
5. Unplug the power cord.
6. Turn the computer upside down, and push down on the latch to release it. Allow the...

 
4 -  
Power Mac G4 Cube Take Apart
 Computer Enclosure 8. Holding the core by the latch, insert the core into the replacement enclosure. 
Note:  
 The core fits into the enclosure only one way. Position the core so the ports 
are toward the back of the enclosure.
9. With a ßat hand, press down on the latch until it locks into place. Firmly press the core 
to ensure it is fully secured within the enclosure.  
Important: 
 Do not lift or carry your computer by the core latch. The enclosure could 
fall...

 
Power Mac G4 Cube Take Apart -   
5  
 Battery 
Battery
 
Tools
 
No tools are required for this procedure. 
Preliminary Steps
 
Before you begin, remove the computer core from the enclosure. 
Procedure
 
1. Note the orientation of the installed batteryÕs positive (+) end. (Positive and negative 
signs are also marked on the battery holder.)
2. Use your Þnger to gently pry the battery out of the holder and out of the computer.  
Warning: Batteries contain chemicals, some of which may be harmful to the...

 
6 -  
Power Mac G4 Cube Take Apart
 Battery  
only the battery supplied. 
4. Reassemble and test the computer. 
Warning: 
  
Never turn on the computer unless all of its internal and external 
parts are in place and it is closed. Operating the computer when it is open or 
missing parts can damage the computer or cause injury. 

 
Power Mac G4 Cube Take Apart -   
7  
 Power Button Gasket 
Power Button Gasket
 
Tools
 
No tools are required for this procedure. 
Preliminary Steps
 
Before you begin, remove the computer core from the enclosure. 

 
8 -  
Power Mac G4 Cube Take Apart
 Power Button Gasket 
Procedure
 
1. Place your hand in the computer enclosure and lift out the installed gasket. 
2. Insert the replacement power button gasket into the recessed area that encircles the 
power button. 
3. Press the gasket into place to ensure that it is secure.
4. Reassemble and test the computer. 
Warning: 
  
Never turn on the computer unless all of its internal and external 
parts are in place and it is closed. Operating the computer when it is...