Asko W6884 Operating Instructions

Rinse holes under the agitator
If you suspect that objects such as nails or paper
clips may have fallen into the wash drum, you
should check the space under the agitator. Such
objects can rust and cause spots on clothing.
Nails and other sharp objects can cause holes in
fabrics.
Do as follows:
1.
Insert a screwdriver or the like into the hole on
the agitator as illustrated and carefully pry to
the left. 2.
Use your other hand to grasp the agitator and
pull it towards you. 3.
Lift the agitator.
4. Remove...

The washer door will not open
1.
Check that the main power switch is on.
2. Is there power? Check your home’s fuses
(circuit breakers). The washer door cannot be
opened with the Door opening button (with the
key symbol) if power is off.
If nothing else works, the washer door can
be opened as follows: Caution!
The door may only be opened manually if the
electric power is cut and the machine has
been drained of water.
A First empty the water from the washing
machine. If the Drain program cannot be
run the...

Error messages
If an error occurs during the program a message
is shown on the display. To exit the message after
taking measures, turn the machine off and then
back on.
The error messages that may be shown in the
display are:
Close the door
Close the washer door and the program will start.
Overfilling
1.
Shut off the water tap.
2. See "Drainage error".
Drainage error
Check:
• that no objects are stuck in the drainage hose
outlet.
• that the drainage pump is not blocked by
foreign objects. Clean...

Technical data
850mm
Height:
595mm
Width:
585mm
Depth:
73kg
Weight:
60l
Cylinder volume:
7kg
Max. washing capacity:
400-1800
Spin speed (rpm):
See type plate.
Rated power:
See type plate.
Heater output:
0,1-1 MPa
1-10 kp/cm2
10-100 N/cm 2
Water pressure:
Stainless steel
Wash drum and liquid compartment material:
Powder-coated and hot-galvanized sheet steel or
stainless steel.
Outer casing material:
1,5m pex pipe
Water connection:
1,7m polypropylene hose
Drain:
Information for test institute
Energy...

Loading procedure for standard test:
When loading the machine for testing according to AS/NZS 2040:2005 it shall be loaded according to
the table below. Garments are placed on top of each other in layers and the soil swatches should be
placed inside the wash drum in the direction shown in the table, seen from above.
Illustration of loaded Wash Drum for standard test.
Swatch placement
Top of the drum
Left
24. Bath towel
Right
23. Pillow case
Front
22. Pillow case
Rear
21. T-shirt
Right
20. Tablecloth
19....

Before the machine is used, the three transport
screws should be removed as shown below.
1.
Loosen and remove the screws. 2.
The enclosed plastic bag contains three plastic
plugs to fit in the empty screw holes. Note!
If the machine is to be moved and transported,
the transport screws must be refitted to prevent
damage to the machine through shaking. If the
transport screws or plastic plugs have been lost
you can order new ones from your retailer.
Designation
Article number
Screw
80 882 77
Plastic plug...

Positioning the washing machine
The washing machine can be installed as a built-in
or freestanding unit. Position the machine so that
the electrical plug is easily accessible.
A. Built-in
The washing machine can be installed under a
counter top with a working height of 850–900 mm.
Leave a 5 mm space around the entire machine,
including between the rear edge of the top cover
and the wall behind it.
B. Freestanding
The washing machine can be positioned beside
or under a tumble dryer.
Adjusting the feet...

Drainage connection
The machine is supplied with a drainage hose
attached, which must be connected to a drain.
See the examples below. The height must be
600–900 mm above floor level.
The lower position (600 mm) is always preferable.
Ensure that the drainage hose has no kinks.
The machine can also be connected to the drain
via a spigot connection. In this case the hose
should also be 600-900 mm above the floor. The
internal diameter of the hole should be at least 18
mm.
•
Cut the nipple
• Remove burrs...

Before contacting the service
division
Before you contact the service division, make sure
that you know the model number (located on the
front panel), and serial number.
The model designation can be found on the panel.
The type designation and serial number can be
found on the type plate on the inside of the washer
door.
29
Service
2
Type
Serial number (12 digits)
70.2   
Serial Number
Model Number   

30Your notes