Asus A6jc Service Guide

							
                          Disassembly Procedure 
 
2 – 1 
Chapter 
2 
Disassembly Procedure 
Please follow the information provided in this section to perform the complete 
disassembly procedure of the notebook.  Be sure to use proper tools 
described before. 
SUS A6Jc/Jm Notebook consists of various modules. This chapter describes the 
procedures for the complete notebook disassembly.  In addition, in between procedures, 
the detailed disassembly procedure of individual modules will be provided for your 
service needs. 
The disassembly procedure consists of the following steps: 
 
 A
• Battery Module 
• Memory Module 
• Wireless LAN Module 
• HDD Module 
• ODD Module 
• Keyboard  
• LCD Module 
• Top Case Module 
• Main Board Module 
• Modem Module 
• CPU/Heat Sink Module 
 
 
 
 
 
 
 
 
 
  
						

							
                     Disassembly Procedure 
 
2 - 2 
Battery Module BATTERY The illustration below shows how to remove the battery module.  
 
1. Unlock and hold the latches, and remove the battery. 
 
  
 
SECOND 
MEMORY 
MODULE 
MEMORY 
REMOVAL 
L 
2. Slide the battery latch (No.1) to unlock and Firmly slide the other latch (No.2) to the top and 
remove the battery 
 
              
        
              
Memory Module 
The A6Jc/Jm Notebook do not have onboard RAM. There are two SO-DIMM sockets 
for installing SO-DIMM RAM. It can upgrade the total memory size up to 2GB with a 
1GB module on each socket.  
 
Removing Memory module  
1. Remove 2 screws and remove DIMM door. 
  
						

							
                     Disassembly Procedure 
 
2 - 3 
         
 
2. Take the memory DIMM cover away as the picture shows. 
 
   
                   
 WIRELESS LAN 
MODULE 
REMOVAL 
Wireless Lan Module 
The illustration below show show how to remove the Wireless LAN module 
 
Disassembling Wireless Lan board. WIRELESS LAN 
REMOVAL  
1. Remove 2 Antenna cables from Wireless LAN Module. 
 
                                                                      
 
  
						

							
                     Disassembly Procedure 
 
2 - 4 
2. Take the Wireless Lan away as the picture shows.  
 
   
30° 
 
 
HDD Module HDD MODULE 
The illustrations below show how to remove the HDD module from the notebook. 
 
HDD 
MODULE 
REMOVAL 
Removing HDD Module 
1. Remove 1 screw and lift the HDD cover away. 
  
      
 
 
 
 
 
 
 
 
 
 
 
 
 
 
               
						

							
                     Disassembly Procedure 
 
2 - 5 
               
    
2. Remove the sponch and pull the hard disk module toward the direction of the arrow and lift it 
up and take it out. 
 
   
 
 
ODD Module OPTICAL 
DRIVE 
REMOVAL 
 
1. Remove 2 screws. 
 
       
       
2. Remove the Mylar. 
 
 
 
 
  
						

							
                     Disassembly Procedure 
 
2 - 6 
 
3. Push the metal plate with a screw driver and pull the ODD out. 
 
 
 
 
CPU MODULE 
REMOVAL 
CPU Module 
The illustrations below show how to remove the CPU module from the notebook. 
 
CPU 
REMOVAL 
Removing CPU 
 
1. Remove 2 screws. 
 
 
2. Remove the mylar. 
 
 
  
						

							
                     Disassembly Procedure 
 
2 - 7 
 
3. Remove 4 screws aside the CPU. And take away the thermal module. 
 
       
3 
2 1 
4 
 
4. Turn the non-removable screw here 180 degrees counter-clockwise to loosen the CPU.  
 
    
Unlock 
L 
 
 
O 
 
 
LCD Module LCD 
MODULE The illustrations below show how to disassemble the LCD module.  The module 
contains LCD panel, Inverter board, LCD Hinge bracket, Hinge cover, LCD front 
cover, LCD back cover. 
 LCD 
DISASSEMBLY 
 
Disassembling LCD Module 
1. Remove 3 screws on both side. 
  
						

							
                     Disassembly Procedure 
 
2 - 8 
           
 
2. Remove both hinge covers 
 
   
 
3. Remove 2 screws on the harness cover and take it away. 
 
    
 
 
4. Remove 1 piece of tape. 
  
						

							
                     Disassembly Procedure 
 
2 - 9 
 
 
5. Remove 1 screw and disconnect the connector.  
 
          
 
6. Remove 1 screw and disconnect the connector.  
 
     
 
 
7. Remove 2 screws on both ends.  
  
						

							
                     Disassembly Procedure 
 
2 - 10 
     
 
     
 
8. Remove the LCD module from system.  
 
     
 
 
LCD 
DISASSEMBLY 
 
Disassembling LCD Module 
1. Remove 5 rubber pads and 5 screws(M2.5 x 8L) from LCD module.