Avaya Partner Advanced Communications System 1600 Dsl Module User Guide

							Avaya, Inc. - 130 - PARTNER ACS 1600 DSL module User Guide
5. Type the new IP address, or press ENTER to select the
current IP address.
The following instructions display on-screen:
Current subnet mask = 0.0.0.0
Enter new subnet mask for this interface:
6. Type the new subnet mask address, or press ENTER to
select the current subnet mask.
The following instructions display on-screen:
Select priority Normal/High [N/H] (N):
7. Do one of the following, and then type Y:
To give the interface high priority, type H.
To give the interface normal priority, type N.
The Router Configuration Menu redisplays.
8. Repeat steps 1-6 for each port for which you want to
configure an IP address.
You must restart the PARTNER ACS 1600 DSL module
for any changes to take effect.  For more information on
restarting the PARTNER ACS 1600 DSL module, see the
“Getting started” chapter.
Enabling RIP
poisoned
reverse
When you enable RIP, the PARTNER ACS 1600 DSL module
sends routing data to other adjacent routers and dynamically
“learns” the associated network topology.
For RIP to work, you must enable RIP globally or locally (by
port), and then setting the RIP version.  The order in which
you perform the procedures is irrelevant. 
						

							Avaya, Inc. - 131 - PARTNER ACS 1600 DSL module User Guide
Enabling RIP poisoned reverse globally
To enable RIP poisoned reverse globally:
1. On the Main Menu, select Configure IP Router.
The Router Configuration Menu displays.
*****************************************
* Router Configuration Menu *
*****************************************
C. Configure Port IP Address
U. Unconfigure Port IP Address
S. Add/Remove a Static Route
R. Enable/Disable RIP
V. Configure RIP Version by Port
P. Configure RIP Poisoned Reverse by Port
N. Configure DNS Client
H. Configure DHCP Client
L. Configure DHCP Relay
T. Configure Telnet Server Port
F. Configure IP Filtering
D. Display Route Table
2. Select Enable/Disable RIP, and then type E.
The Router Configuration Menu redisplays.
You must restart the PARTNER ACS 1600 DSL module
for any changes to take effect.  For more information on
restarting the PARTNER ACS 1600 DSL module, see the
“Getting started” chapter. 
						

							Avaya, Inc. - 132 - PARTNER ACS 1600 DSL module User Guide
Enabling RIP poisoned reverse by port
To enable RIP poisoned reverse by port:
1. On the Main Menu, select Configure IP Router.
The Router Configuration Menu displays.
*****************************************
* Router Configuration Menu *
*****************************************
C. Configure Port IP Address
U. Unconfigure Port IP Address
S. Add/Remove a Static Route
R. Enable/Disable RIP
V. Configure RIP Version by Port
P. Configure RIP Poisoned Reverse by Port
N. Configure DNS Client
H. Configure DHCP Client
L. Configure DHCP Relay
T. Configure Telnet Server Port
F. Configure IP Filtering
D. Display Route Table
2. Select Configure RIP Poisoned Reverse by Port.
The following instructions display on-screen:
Available Interfaces :
1. SDSL
2. 10/100BaseT Ethernet
3. Universal Serial
0. (Abort)
Selection :
Interfaces may or may not display, depending on the IAD
in use.
3. Type the number of the port for which you want to enable
poisoned reverse.
The following instructions display on-screen:
RIP Poisoned Reverse for Slot 1, Port 1 is
currently DISABLED
Enter E to Enable, D to Disable : 
						

							Avaya, Inc. - 133 - PARTNER ACS 1600 DSL module User Guide
4. Type E.
The Router Configuration Menu redisplays.
5. Repeat steps 1-3 for each port for which you want to
enable RIP poisoned reverse.
You must restart the PARTNER ACS 1600 DSL module
for any changes to take effect.  For more information on
restarting the PARTNER ACS 1600 DSL module, see the
“Getting started” chapter.
Setting the RIP version
To set the RIP version:
1. On the Main Menu, select Configure IP Router.
The Router Configuration Menu displays.
*****************************************
* Router Configuration Menu *
*****************************************
C. Configure Port IP Address
U. Unconfigure Port IP Address
S. Add/Remove a Static Route
R. Enable/Disable RIP
V. Configure RIP Version by Port
P. Configure RIP Poisoned Reverse by Port
N. Configure DNS Client
H. Configure DHCP Client
L. Configure DHCP Relay
T. Configure Telnet Server Port
F. Configure IP Filtering
D. Display Route Table
2. Select Configure RIP Version by Port.
The following instructions display on-screen:
Available Interfaces :
1. SDSL
2. 10/100BaseT Ethernet
3. Universal Serial
0. (Abort)
Selection :
Interfaces may or may not display, depending on the IAD
in use. 
						

							Avaya, Inc. - 134 - PARTNER ACS 1600 DSL module User Guide
3. Type the number of the port for which you want to
configure the RIP poisoned reverse version.
The following instructions display on-screen:
Enter RIP Version for Port 1
0. Disabled
1. Version 1 Broadcast
2. Version 2 Broadcast
3. Version 2 Multicast
4. Select your choice, and then press any key.
The Router Configuration Menu redisplays.
5. Repeat steps 1-4 for each port for which want to set the
RIP poisoned reverse version.
You must restart the PARTNER ACS 1600 DSL module
for any changes to take effect.  For more information on
restarting the PARTNER ACS 1600 DSL module, see the
“Getting started” chapter. 
						

							Avaya, Inc. - 135 - PARTNER ACS 1600 DSL module User Guide
Adding a static
route
To add a static route:
1. On the Main Menu, select Configure IP Router.
The Router Configuration Menu displays.
*****************************************
* Router Configuration Menu *
*****************************************
C. Configure Port IP Address
U. Unconfigure Port IP Address
S. Add/Remove a Static Route
R. Enable/Disable RIP
V. Configure RIP Version by Port
P. Configure RIP Poisoned Reverse by Port
N. Configure DNS Client
H. Configure DHCP Client
L. Configure DHCP Relay
T. Configure Telnet Server Port
F. Configure IP Filtering
D. Display Route Table
2. Select Add/Remove a Static Route.
The Router Modification Menu displays.
*****************************************
* Router Modification Menu *
*****************************************
A. Add a Static Route
R. Remove a Route
F. Add/Change the Default Route
T. Remove the Default Route
D. Display Route Table
3. Select Add a Static Route.
4. Type the destination address that you want to add, and
then press ENTER.
5. Type the network mask, and then press ENTER. 
						

							Avaya, Inc. - 136 - PARTNER ACS 1600 DSL module User Guide
6. Type the gateway address, press ENTER, and then type
Y.
The Router Modification Menu redisplays.
7. Repeat steps 1-6 for each route that you want to add.
You must restart the PARTNER ACS 1600 DSL module
for any changes to take effect.  For more information on
restarting the PARTNER ACS 1600 DSL module, see the
“Getting started” chapter.
Adding a
default route
To add a default route:
1. On the Main Menu, select Configure IP Router.
The Router Configuration Menu displays.
*****************************************
* Router Configuration Menu *
*****************************************
C. Configure Port IP Address
U. Unconfigure Port IP Address
S. Add/Remove a Static Route
R. Enable/Disable RIP
V. Configure RIP Version by Port
P. Configure RIP Poisoned Reverse by Port
N. Configure DNS Client
H. Configure DHCP Client
L. Configure DHCP Relay
T. Configure Telnet Server Port
F. Configure IP Filtering
D. Display Route Table
2. Select Add/Remove a Static Route.
The Router Modification Menu displays.
*****************************************
* Router Modification Menu *
*****************************************
A. Add a Static Route
R. Remove a Route
F. Add/Change the Default Route 
						

							Avaya, Inc. - 137 - PARTNER ACS 1600 DSL module User Guide
T. Remove the Default Route
D. Display Route Table
3. Select Add/Change the Default Route.
4. Type the gateway address for the default route, press
ENTER, and then type Y.
The Router Modification Menu displays.
You must restart the PARTNER ACS 1600 DSL module
for any changes to take effect.  For more information on
restarting the PARTNER ACS 1600 DSL module, see the
“Getting started” chapter.
Disabling
bridging
To configure the PARTNER ACS 1600 DSL module as a
router, you must disable bridging both globally and by port.
The order in which you perform the procedures is irrelevant.
When you disable bridging globally, it automatically disables
bridging for all ports and disables the spanning tree protocol.
Disabling bridging globally
To disable bridging globally:
1. On the Main Menu, select Configure Bridge.
The Bridge Configuration Menu displays.
*****************************************
* Bridge Configuration Menu *
*****************************************
G. Enable/Disable Bridging Globally
P. Enable/Disable Bridging by Port
A. Configure Bridge Aging Timer
T. Enable/Disable Spanning Tree Globally
O. Enable/Disable Spanning Tree by Port
R. Configure Spanning Tree Bridge
Priority
Q. Configure Spanning Tree Port Priority
H. Configure Spanning Tree Hello Time
S. Configure Spanning Tree Max Age
F. Configure Spanning Tree Forward Delay 
						

							Avaya, Inc. - 138 - PARTNER ACS 1600 DSL module User Guide
C. Configure Spanning Tree Path Cost
D. Delete Bridge Forwarding Database
Entry
2. Select Enable/Disable Bridging Globally, and the type
D.
The Bridge Configuration Menu redisplays.
You must restart the PARTNER ACS 1600 DSL module
for any changes to take effect.  For more information on
restarting the PARTNER ACS 1600 DSL module, see the
“Getting started” chapter.
Disabling bridging by port
To disable bridging by port:
1. On the Main Menu, select Configure Bridge.
The Bridge Configuration Menu displays.
*****************************************
* Bridge Configuration Menu *
*****************************************
G. Enable/Disable Bridging Globally
P. Enable/Disable Bridging by Port
A. Configure Bridge Aging Timer
T. Enable/Disable Spanning Tree Globally
O. Enable/Disable Spanning Tree by Port
R. Configure Spanning Tree Bridge
Priority
Q. Configure Spanning Tree Port Priority
H. Configure Spanning Tree Hello Time
S. Configure Spanning Tree Max Age
F. Configure Spanning Tree Forward Delay
C. Configure Spanning Tree Path Cost
D. Delete Bridge Forwarding Database
Entry 
						

							Avaya, Inc. - 139 - PARTNER ACS 1600 DSL module User Guide
2. Select Enable/Disable Bridging by Port.
The following instructions display on-screen:
Available Interfaces :
1. SDSL
2. 10/100BaseT Ethernet
3. Universal Serial
0. (Abort)
Selection :
Interfaces may or may not display, depending on the IAD
in use.
3. Type the number of the port for which you want to disable
bridging, and then type D.
4. Repeat steps 1-3 for each port on which you want to
disable bridging.
The Bridge Configuration Menu redisplays.
You must restart the PARTNER ACS 1600 DSL module
for any changes to take effect.  For more information on
restarting the PARTNER ACS 1600 DSL module, see the
“Getting started” chapter.
Disabling STP
To configure the PARTNER ACS 1600 DSL module as a
router, you must disable STP both globally and by port.  The
order in which you perform the procedures is irrelevant.
Disabling STP globally
To disable STP globally:
1. On the Main Menu, select Configure Bridge.
The Bridge Configuration Menu displays.
*****************************************
* Bridge Configuration Menu *
*****************************************
G. Enable/Disable Bridging Globally
P. Enable/Disable Bridging by Port
A. Configure Bridge Aging Timer
T. Enable/Disable Spanning Tree Globally
O. Enable/Disable Spanning Tree by Port