Barco CR Series Projector User Manual

							11
2.4.4 REMOTE CONTROL WARNING
Laser radiation class II product; wavelength 670nm; maximum output 1mW.
Remote control complies with applicable requirements of 21 CFR 1040.10 and 1040.11.
Remote control complies with applicable requirements of EN/IEC 60825-1/2007
Use of controls or adjustments, or performance of procedures other than those  
specified in the User Guide, may result in hazardous radiation exposure.
2.4.5 WARNING SYMBOLS
Here is a list of warning symbols found on the product lable(s):
READ USER GUIDE Attention! Read the user guide for further information!
DANGEROUS VOLTAGE Danger! High voltage inside the product!
HOT Warning! Hot surfaces!
WAIT Warning! Wait until cooled down!
MERCURY Warning! Lamp contains mercury! Recycle properly,  
do not dispose of in ordinary waste!
UV Warning! UV radiation inside the product!
 RECYCLE Warning! Recycle properly, do not dispose of in ordinary waste! 
2.5 FCC
FCC regulations provide that changes or modifications not expressly approved by the party 
responsible manufacturer could void your authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a\
 Class A digi-
tal device, pursuant to part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference when the equipment is operated 
in a commercial environment. This equipment generates, uses, and can radiate radio 
frequency energy and, if not installed and used in accordance with the instruction 
manual, may cause harmful interference to radio communications. Operation of this 
equipment in a residential area is likely to cause harmful interference in which case the 
user will be required to correct the interference at his own expense. 
This device complies with part 15 of the FCC Rules. Operation is subject\
 to the following two conditions: 
(1) This device may not cause harmful interference, and
(2)  this device must accept any interference received, including interference that may cause undesired operation. 
CANADA
This Class A digital apparatus complies with Canadian ICES-003. / Cet ap\
pareil numérique 
de la classe A est conforme à la norme NMB- 003 du Canada.
WARNING
This is a Class A product. In a domestic environment this product may cause radio 
interference, in which case the user may be required to take adequate measures. 
english   
						

							12User’s Guide - Safety InstructionsCR series 
User Manual - Safety Instructions
2.6 WEEE INFORMATION
This product conforms to all requirements of the EU Directive on waste electrical and elec-
tronic equipment (WEEE). This product shall be recycled properly. It can be disassembled to 
facilitate proper recycling of it’s individual parts. This product is using projection lamps that 
shall be recycled properly. Consult your dealer or relevant public authority regarding drop-off 
points for collection of WEEE.
2.6.1 Turkey RoHS compliance
Türkiye Cumhuriyeti: EEE Yönetmeliğine Uygundur. 
(Republic of Turkey: In conformety with the EEE Regulation)
2.7 ENVIRONMENTAL INFORMATION
2.7.1 Disposal Information
Waste Electrical and Electronic Equipment
This symbol on the product indicates that, under the European Directive 2002/96/EC govern-
ing waste from electrical and electronic equipment, this product must not be disposed of 
with other municipal waste. Please dispose of your waste equipment by ha\
nding it over to a 
designated collection point for the recycling of waste electrical and electronic equipment. To 
prevent possible harm to the environment or human health from uncontrolled waste disposal, 
please separate these items from other types of waste and recycle them responsibly to pro-
mote the sustainable reuse of material resources.
For more information about recycling of this product, please contact your local city office or 
your municipal waste disposal service.
For details, please visit the Barco website at: http://www.barco.com/en/AboutBarco/weee
2.7.2 Disposal of batteries in the product
This product contains batteries covered by the Directive 2006/66/EC which must be col-
lected and disposed of separately from municipal waste.
If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium 
(Cd), these chemical symbols will appear below the crossed-out wheeled bin symbol.
By participating in separate collection of batteries, you will help to e\
nsure proper disposal 
and to prevent potential negative effects on the environment and human health.
2.8 SERVICE INFORMATION
This product contains no user serviceable parts. If the product fails to function as expected, 
please first check that all connections are properly made, and that the power cord is properly 
connected. Please check that the projector as well as the video and computer sources are all 
switched on. Cables and cords may break over time. Try to change cables and cords, in case 
there is a bad or intermittent connection. Check if the circuit breaker or fuse of your mains 
is intact. In the event of product failure, please contact your reseller. You should prepare a 
description of the symptoms of failure you experience. Please also state product number and 
serial number as printed on the label on the bottom of the projector. 
english   
						

							13
english   
						

							15
3 What’s in the box?
The following components are standard delivery:
Projector
Power Cable (Country Dependent)
Remote Control
User Documentation
Additional accessories available for the projector:
DVI-cable
Please verify that you have all compoents upon unpacking the unit, and i\
ts contents. Check 
next page for additional accessories.
Please save packaging materials for future use, should it be necessary to ship the unit.
english   
						

							16User Manual - What’s in the Box?CR series 
User Manual - What’s in the box?
english   
						

							17
4 Getting to know the projector
4.1 Overview
A Lens 
B IR sensor 
C1 Ventilation - Air flow IN
C2 Ventilation - Air flow OUT
D  Lens release 
E  Power connector 
F Keypad 
G Connector panel 
H LCD 
I  Lamp lids* 
J Adjustable feet 
K Security lock 
L  Ceiling mount
Figure 4-1.  - Projector front view
Figure 4-2.  - Projector rear view
Figure 4-3. - Projector bottom view
*  Features in the user guide pictures/drawings may be  different from your projector depending on model/version.
* HBGC2BI
F
JJK
B
L
ABCD
B
EC1C1
english   
						

							18User’s Guide – Getting to know the projectorCR series
User Manual - Getting to know the projector
4.2 Indicators
System status indicators are located right of the keypad on the back of the projector. Figure 
4-4 shows the three status indicators – one for each lamp and one for the system statu\
s.
Figure 4-4. The lamp indicators
For the lamp indicators the following apply:
- PERMANENT GREEN LIGHT: The lamp is on and operating normally.
- PERMANENT YELLOW LIGHT: The lamp is off. The lamp may be disabled in the menu or 
the system is in standby.
- PERMANENT RED LIGHT: Lamp life has expired, lamp is not igniting or lamp door is 
open. If the lamp life has expired, please change projection lamp immediately. Failing to 
change lamp may lead to lamp explosion. Please replace with original projectiondesign 
replacement lamp.
- FLASHING YELLOW LIGHT: The lamp is cooling down. The total cooling down time is 
approx. 45 seconds.
- NO LIGHT: No lamp inserted.
The replacement lamps must be purchased from an authorized projectiondesign dealer 
for the warranty of the product to be valid. Using lamps from any other after market 
supplier will void the warranty.
4.2.1 The status indicator
- PERMANENT GREEN LIGHT: The projector is turned on and in normal operation.
- PERMANENT YELLOW LIGHT: The projector is in standby mode. If the projector was 
powered off by the power saving feature (DPMS), it will automatically power on when you 
connect a valid source. 
- FLASHING YELLOW LIGHT: Please wait. The yellow light will flash a period after power 
cord is connected (20-30 sec.), and a period after going to standby mode \
while lamp is 
cooling down (approximately 45 sec.). The projector may not be turned on again until the 
light has turned to permanent yellow.
- FLASHING RED LIGHT: Projector is overheated. Turn off immediately! Check if air inlets 
are covered or if ambient temperature is outside specifications. The projector cannot be 
restarted until the power cord is disconnected and reconnected again. If the projector 
continues to flash red, you will need to return the unit for service.
* Pictures show backpanel of projector with UHP lamps.  LED illumination projectors have one indicator lamp (LED), instead of two (LAMP 1, LAMP 2).
english   
						

							19
4.2.2 Keypad
The projector has an illuminated keypad on the back of the unit. Figure 4-5 shows the 
keypad.
Figure 4-5.  Projector keypad
The keypad is used to:
- navigate the menu system
- scroll the information in the LCD panel
- directly select input sources
- enter pin code (if enabled)
- power on/off
- adjust basic image functions
The keypad is illuminated for operation in dark environments. Available functions are 
illuminated in yellow while selected (active) functions are illuminated in green. Functions that 
are not available are not illuminated.
4.2.3 Remote control
The remote control allows flexible access to the projector settings, either through direct keys, 
or through the menu system. The remote control is backlit for use in dark environments. 
It also has a data-jack that allows for wired connection to the projector. When the wire is 
connected, the IR (infra-red) beam and internal batteries are switched off. 
The direct sources buttons for VGA1, VGA2, X-Port 2 and YPbPr are not  
available for all versions of the product. If your product does not have these inputs 
implemented the OSD will display “not available” when pressing these buttons.
Do not look into the laser beam when activated on the remote 
control. Laser light may permanently damage eyesight. Avoid 
pointing the laser beam at people or animals.
Only use the supplied remote control, otherwise the result may 
be malfunction.
Figure 4-6. Remote control
    
*  Pictures show backpanel of projector with UHP lamps.  LED illumination projectors have one indicator lamp (LED), instead of two (LAMP 1, LAMP 2).
english   
						

							20User’s Guide – Getting to know the projectorCR series
User Manual - Getting to know the projector
4.3 Connectivity
he projector features a wide range of video inputs and command/control connectors.  
Figure 4-7 shows the connector panel.
Figure 4-7. Connector panel
A LAN: 10/100 Mbit Ethernet connector for command, control and software upgrade.
B RC INPUT: 3.5mm mini-jack connector. Allows connection of external IR receiver or 
wired remote control.
C TRIGGERS: 3.5mm mini-jack connector triggers. Used for controlling peripheral 
equipment like motorized screens.
D 3D SYNC: For 1080/WUXGA 3D projectors used to attach external ir-glass emitters
E  RS-232: Allows for wired remote control and monitoring of many projector functions 
used in installation environments.
F  USB-A: Allows for software upgrades using a standard USB memory stick.
G USB-B: Reserved for future use.
H  SYNC-IN: Allows for taking an external vertical sync signal and using that with the select 
video input. This is mainly used in multiple projector installations with requirement of 
video synchronization between the units. 
I  SYNC-OUT: Constantly outputs the vertical sync signal of the active video input.\
 This 
is mainly used in multiple projector installations with requirement of synchronization 
between the units. 
J DVI-D: Two Dual Link DVI-D connectors with bandwidth up to 330 Mhz total. These 
connectors can also be used to form one uniform image by feeding half of\
 the image 
into each connector. HDCP compliant for sources up 165 Mhz.
K VGA: Two VGA connectors with bandwidth up to 170 Mhz
L  YPbPr: Analog video input supporting YPbPr and RGB (sync-on-green) video standard 
up to 1080i.
M HDMI 1.3: Two HDMI 1.3a connectors with bandwidth up to 165 Mhz each. These 
connectors can also be used to form one uniform image by feeding half of\
 the image 
into each connector. HDCP compliant. All video formats specified by the HDMI 1.3a are 
supported.
A
CB
DE
F
H
I
JK
G
LM
english