Barco Hdx Series Installation Manual

3. Physical installation
4. Place the carry handle on the projector as illustrated. Adjustment knob to the back of the projector.
Make sure that the mounting holes matches the holes in the projector.
5. Insert a bolt in each corner and turn in these bolts.
1
2
Image 3-44
Insert bolts
R5905032 HDX SERIES 23/11/201147 

3. Physical installation
3.6 Mounting the top carry handler
Purpose
This carry handle can be used to transport the projector in an easy way.
Necessary tools
8 mm Allen wrench
Necessary parts
• 4x bolt M10 x 16
• 4x washer
• 1x carry handler
How to mount
1. Place the carry handle on top of the projector so that thefixation holes match the holes in the projector.
1
1
Image 3-45
top carry handle
2. Turn in the 4fixation bolts (1). Insert a washer between the bolt and the carry handle.
48
R5905032 HDX SERIES...

3. Physical installation
3.7 Suspension of the projector with rigging clamps
Rigging points and rigging clamps
When a carrying handle is mounted at the bottom side of the projector, eight slots are available to mount rigging clamps. Four slots
are longitudinally (1) oriented and four slots are transversely (2) oriented. Each slot contains a rigging point of which the position in
the slot can be adjusted depending on the size of the truss installation. The rigging clamps can be attached to those rigging...

3. Physical installation
3. Turn in the rigging clamps (A) into the rigging points using a 17 mm open ended spanner. Place a washer between the clamp
and the rigging point.
Image 3-49
Mount rigging clamps
Warning:Always use four (4) rigging points, equally spread, to suspend the projector.
4. Place all four rigging clamps in open position.
5. Place the projector (upside down) under the truss installation and lower the truss until the support bars of the truss are nearby
the rigging clamps mounted on the...

3. Physical installation
7. Lock all four rigging clamps by turning thefixation handle clockwise.
Image 3-51
Clampfixation
8. Install the 2 safety cables, one on both sides of the carrying handle, and around the truss.
Mount the 2 safety cables around the carry handle (push the hook through the loop and then around the truss so that there is not
to much play (maximum 20 cm). If necessary turn the cable a few times around the truss before clasping the safety hook around
the cable.
Image 3-52
Security...

3. Physical installation
3.8 Alignment of a ceiling mounted projector
Necessary tools
No tools.
Skew adjustment
1. Turn the adjustment knob on the carry handle until the projected hatch pattern is perfectly squared.
Skew
Image 3-53
Skew adjustment
52R5905032 HDX SERIES 23/11/2011 

4. Input & Communication
4. INPUT & COMMUNICATION
Overview
• Introduction
• Input source connections
• Communication connections
• Utility-Accessory Outlet
R5905032 HDX SERIES 23/11/2011
53 

4. Input & Communication
4.1 Introduction
General
The Input & Communication side of the projector consists of a button module, a dual 3G/HDSDI and DVI-I input as standard input
module and 2 free input slots. The free input slots can be used for optional modules (f.e. 5-cable input).
1
2
3
4
5
6
7
9
10
11
12
13
15
168
14
Image 4-1
Input & Communication connections
1 Display
2
Optional antenna for Wificonnection
3 12 V output as power supply to external equipment
4 DMX in - out
5
XLR input port for remote...

4. Input & Communication
4.2 Input source connections
DVI and 3G/HDSDI input
This input module is standard delivered with the HDX projector.
DUAL LINK DVI-I HDCP
INPUTSEL
SYNC3G/DUAL HDSDI
OUT1 IN1
IN2OUT2 SEL
SYNCSEL
SYNCR9864000
Image 4-2
Dual Link DVI and 3G/Dual HDSDI input
The yellow LED lights up when valid input sync is detected.
The green LED lights up when the input is selected.
DVI input specifications :
• RGB analog : up to 170 MHz.
• Single DVI : up to 165 MHz
• Dual link DVI : up to 200 MHz...

4. Input & Communication
• Data and HD sources RGB and YUV [HS/VS, CS or SOG(Y)]:
- Pixel clock maximum 200 MHz
- 8 bit digital output
• Video sources CVBS, S-VIDEO, RGB and YUV [CS, CV or SOG(Y)]:
- PAL B/D/I/G/H, PAL60, PAL M, PAL N, PAL Nc
- NTSC M/J, NTSC 4.43
- SECAM B/D/G/K/L
- 525i, 625i, 525p, 625p
- Macrovision copy protection robust
- Standard images “video525” and “video625”
• Automatic detection of sync inputs but with manual override:
- automatic modes : RGB, YUV, VIDEO
- manual modes : RGB...