Beko Dv 7220 X Manual

							11EN
Preparing the machine1. Plug in your machine. 2. Place the laundry in the machine. 3. Press the “On/Off” button.C Pressing the “On/Off” button does not necessarily mean that the programme has started. Press "Start/Pause/Cancel" button of the machine to start the programme.Programme selectionDecide the appropriate programme from the table below which includes drying temperatures in degrees. Select the desired programme with the programme selection button.
Extra dry 
Dry at high temperature only for cotton laundry. Thick and multi layered laundry (E.g.: towels, linens, jeans) are dried in a way that they do not require ironing before placing in the wardrobe.
Ready to wear 
Normal laundry (E.g.: tablecloths, underwear) are dried in a way that they do not require ironing before placing in the drawers.
Ready to wearPlus
Normal laundry (E.g.: tablecloths, underwear) are dried in a way that they do not require ironing before placing in the drawers, but more than those in the ready to wearoption.
Iron DryNormal laundry (E.g., Shirts, dresses) are dried ready to be ironed.
C For further program details, see, “Program Selection Table”Main programmesDepending on the type of laundry, the following main programmes are available:•CottonsYou can dry your durable laundry with this programme. Dries at high temperature. It is recommended to use for your cotton items (such as bed sheets, quilt cover, underclothing, etc.).•SyntheticsYou can dry your less durable laundry with this programme. It dries at a lower temperature compared to the cottons programme. It is recommended for your synthetic laundry (such as shirts, blouses, synthetic/cotton blended laundry, etc.).C Do not dry curtains and lace in your machine.•Anti-creasingA 2-hour anti creasing programme to prevent 
laundry from creasing will be activated if you do not take the laundry out after the programme is over. This programme rotates the laundry in 10-minute intervals to prevent creasing.Special programmes For special cases, there are also extra programmes available:C Additional programmes may differ according to the model of your machine.•MiniYou can use this programme to dry the cottons that are spun at high speeds in your washing machine. It can dry your 1,2 kg Cotton laundry (3 Shirts / 3 T-Shirts) within 30 minutes.C In order to obtain better results from the dryer programs, your laundry must be washed with suitable program and spun at the recommended spin speeds in your washing machine.•Shir t Dries the shirts in a more sensitive way so that they are less creased and ironed easily.C Shirts may contain little amount of dampness at the and of the program. It is advised not to leave the shirts in the dryer.•Jeans You can use this program to dry the jeans that are spun at high speeds in your washing machine.C Review the relevant part of the program table.•DelicatesYou can dry at a lower temperature your very delicate laundry (silk blouses, fine underwear, etc.) that are suitable for drying or laundry which is advised to be hand-washed.C It is recommended to use a cloth bag to avoid certain delicate garments and laundry from getting creased or damaged. Take your garments immediately out of the dryer and hang them after the programme ends in order to prevent them being creased. •VentilationOnly ventilation is performed for 10 minutes without blowing hot air. You can air your clothes that have been kept at closed environments for a long time thanks to this program to deodorize unpleasant odors.•Timer programsYou can select one of the 10 min., 20 min., 40 min. and 60 min. timer programmes to achieve the desired final drying level at low temperatures. Programme dries at the selected time regardless of the drying temperature.  
						

							12EN
Program selection and consumption table
* : Energy Label standard program (AS/NZS 2442)All values given in the table have been fixed according to standard laboratory conditions. These values may deviate from the table according to the laundry type, laundry spin speed, environmental conditions and voltage fluctuations.
EN2
ProgramsCapacity (kg)Spin speed in washing machine (rpm)
Approximate amount of remaining humidity
Drying time (minutes)
Cottons / Coloreds
A Ready to Wear
71200-1000% 60135
900-800% 70150
3.51200-1000% 6075
900-800% 7090
AReady to Wear Plus
71200-1000% 60140
900-800% 70160
3.51200-1000% 6085
900-800% 70100
A Ready to Iron
71200-1000% 60100
900-800% 70115
3.51200-1000% 6060
900-800% 7075
Mini1.21200-1000%5030
Shirt1.51000-800%5049
Jeans41200-1000%50100
Synthetics
B Ready to Wear
3.5800% 4055
600% 5070
1.75800% 4035
600% 5045
Delicates
B Ready to Wear1.5600% 5040
Energy consumption values
ProgramCapacity (kg)Energy consumption value kWh per yearEnergy rating star
 Cottons-Ready to Wear Plus*73052.0  
						

							13EN
Auxiliary functionCancel audio warningYour dryer will give an audio warning when the programme comes to an end. If you do not want to hear the audio warning, press “Cancel Audio Warning” button. The relevant light will turn on when this button is pressed and an audio warning will not be given when the programme comes to an end.CYou can select this function either before or after the programme starts. Warning indicatorsCWarning indicators may differ according to the model of your dryer.Filter cleaningA warning light will turn on to remind filter cleaning after the programme finishes.CIf the filter cleaning warning light lights up continuously, please refer to, “Suggested solutions for problems”.Time delayIf you wish to dry your clothes at a later time, thanks to the time delay function, you can delay the program start up to 3 hours, 6 hours or 9 hours.1. Open the loading door and put the laundry in.CMake sure that all air outlets are open, door filter is cleaned and the water tank is empty.2. Set the drying program and, if required, the auxiliary functions.3. When the time programming button is pressed once, a 3 hour delay is selected and the relevant led lights. When the same button is pressed again, 6 hours; and if pressed once more, 9 hours delay will be selected. If the time programming button is pressed one more time, time delaying function will be cancelled. Set the time delay as you require.4. Delayed operation of the selected program is started by pressing the "Start/Pause/Cancel" button after selecting the time delay. CAdditional laundry may be loaded / taken out during the time delay period.CDuring the time delay period, laundry is rotated for 4 seconds in every 10 minutes to prevent creasing.Canceling the time delayIf you want to cancel the time delay countdown and start the program:1. Press “Start/Pause/Cancel” button for about 3 seconds. 2. Press “Start/Pause/Cancel” button to start the program right away.Star ting the programme1. Press “Start/Pause/Cancel” button to start the programme.
2. Light of the “Start/Pause/Cancel” button will turn on to indicate that the programme has started.Progress of programProgress of a running program is shown through the program follow-up indicator.At the beginning of every program step, the relevant indicator LED will light up and light of the completed step will turn off.“Drying”:- Drying level will be illuminated during the whole drying process until the drying degree reaches “iron dry”.“Iron Dry”:- Starts to illuminate when the drying degree reaches “iron dry” step and remains illuminated until the next step.“Ready to wear”:Starts to illuminate when the drying degree reaches “Ready to wear” step and remains illuminated until the next step. “Final / Anti-creasing”:- Illuminates when the program comes to an end and anti-creasing function is activated.
C If more than one LED light up or flash concurrently, it means there is malfunctioning or a failure (please see, Solution suggestions for problems).
Changing the programme after it has star tedYou can use this feature to dry your clothes under higher or lower temperatures after your dryer has started.For example;1. Press and hold the “Start/Pause/Cancel” button for about 3 seconds to “Cancel” the programme in order to select “Extra Dry” programme instead of “Iron Dry” programme. 2. Select the “Extra Dry” programme by rotating the programme selection button.3. Press “Start/Pause/Cancel” button to start the programme.CPress “Start/Pause/Cancel” button for 3 seconds to cancel the programme or turn the programme selection knob in any direction to end the programme while the machine is running. Water tank and filter cleaning warning lights turn on to warn the user when the programme is cancelled by pressing the “Start/Pause/Cancel” button for 3 seconds. However, the warning lights do not turn on when the programme is cancelled by turning the programme selection knob. Only the drying light turns on and the machine remains in hold until a new programme is selected and the “Start/Pause/Cancel” button is pressed.   
						

							14EN
Child-proof lock of the machine should not be active in order to perform these two operations. If the child-proof lock is active, deactivate it before performing these operations.Adding/removing laundry in standby modeIn order to add or remove laundry after the programme starts:1. Press the “Start/Pause/Cancel” button to switch the dryer to “Pause” mode. Drying process will stop.2. Open the door at “Pause” position and close it again after adding or taking out laundry.3. Press “Start/Pause/Cancel” button to start the programme.CAny laundry added after the drying process has started may cause the dried clothes in the machine intermingle with wet clothes and the result will be wet laundry after the drying process is over.CLaundry may be added or taken out as much as desired during a drying process, but this process will extend the programme duration and increase energy consumption since the drying will be interrupted continuously. Therefore, it is recommended to add laundry before the drying programme has started.Child-proof lockThere is a child-proof lock to prevent any programme interruption due to the pressing of button while the programme is running. The loading door and all buttons except the “On/Off” button on the control panel are deactivated when the child-proof lock is active.Press the “Start/Pause/Cancel” and “Cancel audio warning” buttons simultaneously for 3 seconds to activate the child-press lock. To start a new programme after the programme is over or to interrupt the programme, the child-proof lock should be deactivated. Press the same buttons for 3 sec. again to deactivate the child-proof lock.CChild-proof lock is deactivated when the machine is restarted by pressing the On/Off button.
CPress the relevant buttons for 3 seconds to activate the child-proof lock. A long beep will be heard and the child-proof lock will be activated. A double beep will be heard if you press any button or turn the 
programme selection knob while the child-proof lock is active. Press the buttons for 3 seconds to deactivate the child-proof lock. Single beep will be heard and child-proof lock will be deactivated.A A double beep will be heard if you turn the programme selection knob when the machine is running and the child-proof lock is active. If you deactivate the child-proof lock without returning the program selection knob to its previous position, the programme will be terminated since the position of the programme selection knob is changed. The drying light turns on and the machine remains on hold until a new programme is selected and the “Start/Pause/Cancel” button is pressed.Finishing by canceling the programmeTo cancel any selected programme:Press “Start/Pause/Cancel” button for about 3 seconds. The “Filter cleaning”, “Water tank” and “End/ Anti-creasing” warning lights will turn on at the end of this period for reminding purposes.A As the inside of the dryer will be excessively hot when you cancel the programme while the dryer is running, activate the ventilation programme to cool it down.End of programmeThe “End/Anti-creasing”, “Filter cleaning” and “Water tank” warning lights on the programme follow up indicator will turn on when the programme comes to an end. The door can be opened and the machine becomes ready for a second cycle.Press “On/Off” button to turn off the dryer.CFinal step of the drying cycle (cooling step) is performed without heat application in order to keep the items at a temperature that would not harm them.CA 2-hour anti creasing programme to prevent laundry from creasing will be activated if you do not take the laundry out after the programme has come to an end.CIf you will not take the laundry out immediately, do not stop the dryer before the drying process is complete.CClean the filter after each drying (please see, Filter cleaning).CDrain the water tank after each drying (please see, Water tank)  
						

							15EN
5    Maintenance and cleaning
Filter Car tridge / Door Inner SurfaceLint and fibres released from the laundry to the air during the drying cycle are collected in the “Filter Cartridge”. 
C Such fibre and lint are generally formed during wearing and washing.C Always clean the filter and the inner surfaces of the cover after each drying process.C You can clean the filter and filter area by vacuum cleaner.To clean the filter:1. Open the loading door.2. Remove the cover filter by pulling it up and open the filter.3. Clean lint, fibre, and cotton raveling by hand or with a soft piece of cloth. 4. Close the filter and place it back into its seat.C Clogging may arise on the filter surface after using your machine for some time; if this occurs, wash the filter with water and dry it before using again. C Clean the entire inner surface of the cover and door gasket.
Sensor (models equipped with a sensor)There are humidity sensors in your machine that detect whether the laundry is dry or not.For sensor cleaning;
1. Open the door of the machine.2. Allow the machine to cool off if drying has been carried out.3. Wipe the metal sensors with a soft cloth, dampened with vinegar and dry them.C Clean metal sensors 4 times a year.A Never use solvents, cleaning agents or substances alike when cleaning as these might cause fire and explosion!   
						

							16EN
Drying process takes too much time
• The filter mesh may be clogged. Wash with water.
Laundry come out wet at the end of drying.
• The filter mesh may be clogged. Wash with water.• Excessive laundry might have been loaded in. Do not overload the machine.
Machine does not switch on or the program does not start.  Machine is not activated when set.
• It might have not been plugged in. Make sure that the machine is plugged in.• The loading door may be ajar. Make sure that the loading door is properly closed.• Program might have not been set or the «Start/Pause/Cancel» button might have not been pressed. Make sure that the program has been set and it is not in “Pause” mode.• «Childproof lock» might have been activated. Deactivate the childproof lock.• The condenser cover on the models with a condenser might not be closed securely. Make sure that the condenser cover and the red lock is closed securely.
Program has been interrupted without any cause.
• The loading door may be ajar. Make sure that the loading door is properly closed.• Electricity may be cut off. Press «Start/Pause/Cancel» button to start the program. • The condenser cover on the models with a condenser might not be closed securely. Make sure that the condenser cover and the red lock is closed securely.
Laundry has shrunk, become felted or deteriorated.
• A program suitable for the laundry type might have not been used. Dry only the laundry which is suitable for drying in your machine after checking the labels o\
n your clothes. • Select a program with suitable low temperature for the laundry type to dry your clothes.
Drum lighting does not come on. (for models equipped with a lamp)
• The machine might have not been started by using the On/Off button. Make sure that the machine is On.• Bulb may have blown. Call Beko service to arrange for the bulb to be replaced.• The condenser cover on the models with a condenser might not be closed securely. Make sure that the condenser cover and the red lock is closed securely.
2 beeps heard when the buttons are pressed or the program selection knob is turned.
• Childproof lock» might have been activated. Deactivate the childproof lock.• Program selection knob might be turned to an undefined position.  Select one of the defined programs.
“Filter cleaning” light is flashing.
• Filter might have not been cleaned. Clean the cover filter.
“Final / Anti-creasing” LED is on.
• Program has come to an end. Turn off the machine and take out the laundry.
3 beeps are heard when you press the Start/Pause/Cancel button
• The loading door may be ajar. Make sure that the machine is plugged in.• Make sure that the condenser cover and the red lock is closed securely.
Also for products equipped with a condenser:
“Water tank” warning LED is flashing.
• Water may be full.• Drain the water in the water tank.
A Please call Beko Service if the problem persists.
6   Solution suggestions for problems