Beko Ev 5600 Y Manual
Have a look at the manual Beko Ev 5600 Y Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 187 Beko manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
2820523791_EN / 24-10-15.(23:50) Document Number= Washing Machine User Manual EV 5600Y EN
This product was manufactured using the latest technology in environmentally friendly conditions.
3 / EN 1 Important instructions for safety and environment This section contains safety instructions that will help protect from risk of personal injury or property damage. Failure to follow these instructions shall void any warranty. 1.1 General safety • This product can be used by children at and above 8 years old and by persons whose physical, sensory or mental capabilities were not fully developed or who lack expe- rience and knowledge provided that they are supervised or trained on the safe usage of the product and the risks it brings out. Children must not play with the product. Cleaning and maintenance works should not be performed by children unless they are supervised by someone. • Never place the product on a carpet-covered floor. Otherwise, lack of airflow beneath the machine will cause electrical parts to overheat. This will cause problems with your product. • If the product has a failure, it should not be operated unless it is repaired by the Authorized Service Agent. There is the risk of electric shock! • This product is designed to resume operating in the event of powering on after a power interruption. If you wish to cancel the programme, see "Cancelling the pro- gramme" section. • Connect the product to a grounded outlet protected by a 16 A fuse. Do not neglect to have the grounding installation made by a qualified electrician. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations. • The water supply and draining hoses must be securely fastened and remain undama- ged. Otherwise, there is the risk of water leakage. • Never open the loading door or remove the filter while there is still water in the drum. Otherwise, risk of flooding and injury from hot water will occur. • Do not force open the locked loading door. The loading door will be ready to open just a few minutes after the washing cycle comes to an end. In case of forcing the loading door to open, the door and the lock mechanism may get damaged. • Unplug the product when not in use. • Never wash the product by spreading or pouring water onto it! There is the risk of electric shock! • Never touch the plug with wet hands! Never unplug by pulling on the cable, always pull out by grabbing the plug. • Use detergents, softeners and supplements suitable for automatic washing machines only. • Follow the instructions on the textile tags and on the detergent package. • The product must be unplugged during installation, maintenance, cleaning and repai- ring procedures. • Always have the installation and repairing procedures carried out by the Authorized Service Agent . Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons. • If the power cable is damaged, it must be replaced by the manufacturer, after sales service or a similarly qualified person (preferably an electrician) or someone designa- ted by the importer in order to avoid possible risks. Washing Machine / User’s Manual
4 / EN • Place the product on a rigid, flat and level surface. • Do not place it on a long-pile rug or similar surfaces. • Do not place the product on a high platform or near the edge on a cascaded surface. • Do not place the product on the power cable. • Never use sponge or scrub materials. These will damage the painted, chrome plated and plastic surfaces. 1.2 Intended use • This product has been designed for domestic use. It is not suitable for commercial use and it must not be used out of its intended use. • The product must only be used for washing and rinsing of laundry that are marked accordingly. • The manufacturer waives any responsibility arisen from incorrect usage or transporta- tion. 1.3 Children's safety • Packaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of the children. • Electrical products are dangerous for the children. Keep children away from the pro- duct when it is in use. Do not let them to tamper with the product. Use child lock to prevent children from intervening with the product. • Do not forget to close the loading door when leaving the room where the product is located. • Store all detergents and additives in a safe place away from the reach of the children by closing the cover of the detergent container or sealing the detergent package. While washing the laundry at high temperatures, the loading door glass becomes hot. Therefore, keep especially the children away from the loading door of the machine while the washing operation is in progress. 1.4 Package information • Packaging materials of the product are manufactured from recyclable materials in ac- cordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities. 1.5 Disposing of the waste product • This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Therefore, do not dispose the product with normal domestic waste at the end of its service life. Take it to a collection point for the recycling of electrical and electronic equipment. Please consult your local authorities to learn the nearest collection point. Help protect the environment and natural resour - ces by recycling used products. For children's safety, cut the power cable and break the locking mechanism of the loading door so that it will be non-functional before dis- posing of the product. Washing Machine / User’s Manual
5 / EN 1.6 Compliance with WEEE Directive This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE). This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling. Do not dispose of the waste product with normal domestic and other wastes at the end of its servi- ce life. Take it to the collection center for the recycling of electrical and elec- tronic equipment. Please consult your local authorities to learn about these collection centers. Compliance with RoHS Directive: The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive. Washing Machine / User’s Manual
6 / EN 2 Installation Refer to the nearest Authorised Service Agent for installation of the product. To make the product ready for use, review the information in the user manual and make sure that the electricity, tap water supply and water drainage systems are appropriate before calling the Authorized Service Agent. If they are not, call a qualified technician and plumber to have any necessary arrangements carried out. CInformatIons Preparation of the location and electrical, tap water and waste water installations at the place of installation is under customer’s responsibility. Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or crushed while pushing the product into its place after installation or cleaning procedures. BwarnIng Installation and electrical connections of the product must be carried out by the Authorized Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons. AwarnIng Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products cause risks for your safety. 2.1 Appropriate installation location• Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces. • Total weight of the washing machine and the dryer -with full load- when they are placed on top of each other reaches to approx. 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity! • Do not place the product on the power cable. • Do not install the product at places where temperature may fall below 0ºC. • Place the product at least 1 cm away from the edges of other furniture. 2.2 Removing packaging reinforcementTilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon. 2.3 Removing the transportation locks AwarnIng Do not remove the transportation locks before taking out the packaging reinforcement. Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be damaged. Loosen all the bolts with a suitable spanner until they rotate freely (C). Remove transportation safety bolts by turning them gently. Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel. (P) CInformatIons Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future. Never move the product without the transportation safety bolts properly fixed in place! 2.4 Connecting water supply CInformatIons The water supply pressure required to run the product is between 1 to 10 bars (0.1 – 1 MPa). It is necessary to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a pressure reducing valve if water pressure is higher. If you are going to use the double water-inlet product as a single (cold) water-inlet unit, you must install the supplied stopper to the hot water valve before operating the product. (Applies for the products supplied with a blind stopper group.) If you want to use both water inlets of the product, connect the hot water hose after removing the stopper and gasket group from the hot water valve. (Applies for the products supplied with a blind stopper group.) AwarnIng Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will get damaged or the product will switch to protection mode and will not operate. Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry. Connect the special hoses supplied with the product to the water inlets on the product. Red hose (left) (max. 90 ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is for cold water inlet. AwarnIng Ensure that the cold and hot water connections are made correctly when installing the product. Otherwise, your laundry will come out hot at the end of the washing process and wear out. Tighten all hose nuts by hand. Never use a wrench when tightening the nuts. Open the taps completely after making the hose connection to check for water leaks at the connection points. If any leaks occur, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. To prevent water leakages and damages caused by them, keep the taps closed when the machine is not in use. 2.5 Connecting to the drain• The end of the drain hose must be directly connected to the wastewater drain or to the washbasin. Washing Machine / User’s Manual
7 / EN AwarnIng Do not remove the transportation locks before taking out the packaging reinforcement. • The hose should be attached to a height of at least 40 cm, and 100 cm at most. • In case the hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out excessively wet. Therefore, follow the heights described in the figure. 100cm 40cm • To prevent flowing of dirty water back into the machine and to allow for easy discharge, do not immerse the hose end into the dirty water or do not drive it in the drain more than 15 cm. If it is too long, cut it short. • The end of the hose should not be bent, it should not be stepped on and the hose must not be pinched between the drain and the machine. • If the length of the hose is too short, use it by adding an original extension hose. Length of the hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak. 2.6 Adjusting the feet AwarnIng In order to ensure that the product operates more silently and vibration-free, it must stand level and balanced on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its place and cause crushing and vibration problems. Loosen the lock nuts on the feet by hand. Adjust the feet until the product stands level and balanced. Tighten all lock nuts again by hand. AwarnIng Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged. 2.7 Electrical connectionConnect the product to a grounded outlet protected by a fuse complying with the values in the "Technical specifications" table. Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations. • Connection must comply with national regulations. • Power cable plug must be within easy reach after installation. • The voltage and allowed fuse or breaker protection are specified in the “Technical specifications” section. If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified electrician install a 16 Amp fuse. • The specified voltage must be equal to your mains voltage. • Do not make connections via extension cables or multi- plugs. BwarnIng Damaged power cables must be replaced by the Authorized Service Agents. 2.8 First useBefore starting to use the product, make sure that all preparations are made in accordance with the instructions in sections "Important safety instructions" and "Installation". To prepare the product for washing laundry, perform first operation in Cotton-90 programme. Before starting the programme, put max. 100 g of powder anti-limescale into the main wash detergent compartment (compartment nr. II). If the anti-limescale is in tablet form, put only one tablet into compartment nr. II. Dry the inside of the bellow with a clean piece of cloth after the programme has come to an end. CInformatIons Use an anti-limescale suitable for the washing machines. Some water might have remained in the product due to the quality control processes in the production. It is not harmful for the product. 2.9 Disposing of packaging materialPackaging materials are dangerous to children. Keep packaging materials in a safe place away from reach of the children. Packaging materials of the product are manufactured from recyclable materials. Dispose of them properly and sort in accordance with recycled waste instructions. Do not dispose of them with normal domestic waste. 2.10 Transportation of the productUnplug the product before transporting it. Remove water drain and water supply connections. Drain the remaining water in the product completely; see, "Draining remaining water and cleaning the pump filter". Install transportation safety bolts in the reverse order of removal procedure; see, "Removing the transportation locks". CInformatIons Never move the product without the transportation safety bolts properly fixed in place! 2.11 Disposing of the old productDispose of the old product in an environmentally friendly manner. Washing Machine / User’s Manual
8 / EN 3 Preparation 3.1 Things to be done for energy savingFollowing information will help you use the product in an ecological and energy-efficient manner. • Operate the product in the highest capacity allowed by the programme you have selected, but do not overload; see, "Programme and consumption table". • Always follow the instructions on the detergent packaging. • Wash slightly soiled laundry at low temperatures. • Use faster programmes for small quantities of lightly soiled laundry. • Do not use high temperatures for laundry that is not heavily soiled or stained. • Do not use detergent in excess of the amount recommended on the detergent package. 3.2 Sorting the laundry• Sort laundry according to type of fabric, colour, and degree of soiling and allowable water temperature. • Always obey the instructions given on the garment tags. 3.3 Preparing laundry for washing• Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons will damage the machine. Remove the metal pieces or wash the clothes by putting them in a laundry bag or pillow case. • Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside out and brush. Such objects may damage the product or cause noise problem. • Put small size clothes such as infant's socks and nylon stockings in a laundry bag or pillow case. • Place curtains in without compressing them. Remove curtain attachment items. • Fasten zippers, sew loose buttons and mend rips and tears. • Wash “machine washable” or “hand washable” labeled products only with an appropriate programme. • Do not wash colours and whites together. New, dark coloured cottons release a lot of dye. Wash them separately. • Tough stains must be treated properly before washing. If unsure, check with a dry cleaner. • Use only dyes/colour changers and limescale removers suitable for machine wash. Always follow the instructions on the package. • Wash trousers and delicate laundry turned inside out. • Keep laundry items made of Angora wool in the freezer for a few hours before washing. This will reduce pilling. • Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must be shaken off before placing into the machine. Such dusts and powders on the laundry may build up on the inner parts of the machine in time and can cause damage. 3.4 Correct load capacityThe maximum load capacity depends on the type of laundry, the degree of soiling and the washing programme desired. The machine automatically adjusts the amount of water according to the weight of the loaded laundry. AwarnIng Follow the information in the “Programme and consumption table”. When overloaded, machine’s washing performance will drop. Moreover, noise and vibration problems may occur. Laundry types and their average weights in the following table are given as examples. Laundry type Weight (g) Bathrobe 1200 Duvet cover 700 Bed Sheet 500 Pillowcase 200 Tablecloth 250 Towel 200 Men’s shirt 200 3.5 Loading the laundryOpen the loading door. Place laundry items loosely into the machine. Push the loading door to close until you hear a locking sound. Ensure that no items are caught in the door. CInformatIons The loading door is locked while a programme is running. The door can only be opened a while after the programme comes to an end. AwarnIng In case of misplacing the laundry, noise and vibration problems may occur in the machine. 3.6 Using detergent and softener Detergent DrawerThe detergent drawer is composed of three compartments: - (1) for prewash - (2) for main wash – (3) for softener – (*) in addition, there is siphon piece in the softener compartment. 1 2 3 Refer to your local dealer or solid waste collection centre in your area to learn how to dispose of your product. For children's safety, cut the power cable and break the locking mechanism of the loading door so that it will be nonfunctional before disposing of the product. Washing Machine / User’s Manual