BEKO WKE 14500 D User Manual

17    EN

Program selection and consumption table
• : Selectable* : Automatically selected, not cancellable.**: Energy Label programme (EN 60456)
Water and power consumption and program duration may differ from the table subject to changes in water pressure, water hardness and temperature, ambient temperature, type and amount of laundry, selection of auxiliary functions, and changes in electric voltage.
C The auxiliary functions in the table may differ according to the model of your machine.
Programme...

18    EN

Auxiliary functionsAuxiliary function selection keysSelect the required auxiliary functions before starting the program.
C Auxiliary function buttons may differ according to the model of your machine.
Auxiliary function selectionIf an auxiliary function that should not be selected together with a previously selected function is chosen, the first selected function will be cancelled and the last auxiliary function selection will remain active.For example: If you want to select pre-wash first and...

19    EN

program is started by pressing the "Start/Pause/Cancel" button after making the time delay selection. 
C More laundry may be loaded/removed during the time delay period.
Changing and canceling the time delay.
1.  Press the “Start/Pause/Cancel” 
button to switch the machine to “Pause” mode. 
2.  Press "Start/Pause/Cancel" button 
to start the program after making the new time delay selection. 
C  In the event that any of the lights of 3-6-9 options does not light up after...

20    EN

“Start/Pause/Cancel” button and switch the machine to “Pause” mode in order to change the spin speed or temperature. New spin speed or temperature can be selected.  
Adding/removing laundry in standby modeIf you want to add more laundry into the machine after the washing cycle has started, put the machine into “Pause” mode by pressing the "Start/Pause/Cancel" button. The “Ready” lamp on the program follow-up indicator will light up after 1-2 minutes if the water level in the machine is...

21    EN

Preparation
1.  Turn the tap on completely. Check if 
the hoses are connected tightly.
2.  Place the laundry in the machine.
3.  Add detergent and softener.
Starting
1.  Press the “On/Off” button.
2.  Select the programme and the 
temperature.
3.  If required (according to your 
machine’s model):
–  select any auxiliary function,
–  adjust the spin speed,
–  set the time delay,
4.  Close the loading door.
5.  Press “Start/Pause/Cancel” button.
Canceling a program
•   Press “Start/Pause/Cancel”...

22    EN

program follow-up indicator. Open the loading door and take out the clothes.
2.  Press the “On/Off” button.
3.  Turn the water tap off.
4.  Eliminate any folding of the rubber 
seal on the loading door and check for impurities.
5.  Leave the loading door and detergent 
drawer open to dry.
 

23    EN

Detergent drawerRemove any powder residue buildup in 
the drawer. To do this;
1.  Press the dotted point on the siphon 
in the softener compartment and pull towards you until the compartment is removed from the machine.
C If more than a normal amount of water and softener mixture starts to gather in the softener compartment, the siphon must be cleaned.
2.  Wash the dispenser drawer and the 
siphon with plenty of lukewarm water in a washbasin. Wear protective gloves or use an appropriate brush...

24    EN

under streaming water.
•  Replace the gaskets and filters 
carefully and tighten the hose nuts by hand.
Draining any remaining water 
and cleaning the pump filterFilter system in your machine prevents solid items such as buttons, coins and fabric fibers clogging the pump propeller during discharging of the washing water. Thus, a good water discharger is achieved and the pump life is extended.
•   If your machine fails to drain the 
water, the pump filter may be clogged. You may have to clean...

25    EN

filter to receive water flowing from the filter.
•   Loosen pump filter (anticlockwise) 
until water starts to flow out of it. Direct the flowing water into the container you have placed in front of the filter. You can use a piece of cloth to absorb any spilled water.
•   When there is no water left, turn the 
pump filter until it is completely loose and remove it.
•   Clean any residues inside the filter 
as well as fibers, if any, around the propeller region.
•   If your product has a water...

26    EN

ProblemCauseExplanation / Suggestion
Program cannot be started or selected. 
Machine may have switched to self protection mode due to an infrastructure problem (such as line voltage, water pressure, etc.).
Reset your machine by pressing “Start/Pause/Cancel” button for 3 seconds. (see, Cancelling a Program)
Water in the machine.
There may be some water in your machine when you receive it. This is from the quality control process and is normal.
It is not harmful to your machine.
There is water...