Belkin Router F5D8233-4 User Manual

Alternate  Setup  Method
28
s e c t i o n
2
1
3
4
5
6
7
8
9
10

Setting your Connection Type
From the “Connection Type” page, you can select the type of connection 
you use. Select the type of connection you use by clicking the button 
(1)
next to your connection type and then clicking “Next” 
(2)
.

(2)

(1) 

29

Alternate  Setup  Method
Alternate  Setup  Method

Setting your Internet Service Provider (ISP) Connection
Type to Dynamic IP
A dynamic connection type is the most common connection type found with 
cable modems. Setting the connection type to “dynamic” in many cases is 
enough to complete the connection to your ISP. Some dynamic connection 
types may require a host name. You can enter your host name in the space 
provided if you were assigned one. Your host name is assigned by your ISP. 
Some...

Alternate  Setup  Method
30
s e c t i o n
2
1
3
4
5
6
7
8
9
10

Setting your Internet Service Provider (ISP) Connection Type to Static IP
A  static  IP  address  connection  type  is  less  common  than  other 
connection  types.  If  your  ISP  uses  static  IP  addressing,  you  will 
need  your  IP  address,  subnet  mask,  and  ISP  gateway  address.  This 
information  is  available  from  your  ISP  or  on  the  paperwork  that  your 
ISP  left  with  you.  Type  in  your  information,  then...

31

Alternate  Setup  Method
Alternate  Setup  Method

Setting your ISP Connection Type to PPPoE
Most  DSL  providers  use  PPPoE  as  the  connection  type.  If  you  use  a 
DSL  modem  to  connect  to  the  Inter net,  your  ISP  may  use  PPPoE  to 
log  you  into  the  service.  If  you  have  an  Inter net  connection  in  your 
home  or  small  office  that  doesn’t  require  a  modem,  you  may  also
use  PPPoE.

Your  connection  type  is  PPPoE  if:

1)   
Your  ISP  gave  you  a  user  name...

Alternate  Setup  Method
32
s e c t i o n
2
1
3
4
5
6
7
8
9
10

(1)
(2)

(3)
(4)

(5)

1.  User Name
This  space  is  provided  to  type  in  your  user  name  that  was 
assigned  by  your  ISP.

2.   Password
Type  in  your  password  and  retype  it  into  the  “Retype  Password” 
box  to  confirm  it.

3.  Service Name
A  service  name  is  rarely  required  by  an  ISP.  If  you  are  not  sure  if 
your  ISP  requires  a  service  name,  leave  this  blank.

4.   MTU
The  MTU  setting  should...

33

Alternate  Setup  Method
Alternate  Setup  Method

Setting your Internet Service Provider (ISP) Connection Type to

Point-to-Point Tunneling Protocol (PPTP)

[European Countries Only].
Some  ISPs  require  a  connection  using  PPTP  protocol,  a  type  of 
connection  most  common  in  European  countries.  This  sets  up  a  direct 
connection  to  the  ISP’s  system.  Type  in  the  information  provided 
by  your  ISP  in  the  space  provided.  When  you  have  finished,  click 

“Apply...

Alternate  Setup  Method
34
s e c t i o n
2
1
3
4
5
6
7
8
9
10

6.  My Subnet Mask
Provided  by  your  ISP.  Enter  the  IP  address  here.

7.   Default Gateway
Provided  by  your  ISP.  If  your  ISP  did  not  give  you  a  connection  ID 
(default  gateway),  leave  this  blank.

8.  Disconnect after X....
The  “Disconnect”  feature  is  used  to  automatically  disconnect  the 
Router  from  your  ISP  when  there  is  no  activity  for  a  specified 
period  of  time.  For  instance,  placing  a...

35

Alternate  Setup  Method
Alternate  Setup  Method

Setting your Connection Type if you are a Telstra
®
 BigPond User
[Australia  Only].  Your  user  name  and  password  are  provided  to  you 
by  Telstra  BigPond.  Enter  this  information  below.  Choosing  your  state 
from  the  drop-down  menu 
(6)
  will  automatically  fill  in  your  login  server 
IP  address.  If  your  login  server  address  is  different  than  one  provided 
here,  you  may  manually  enter  the  login  server  IP...

Alternate  Setup  Method
36
s e c t i o n
2
1
3
4
5
6
7
8
9
10

4.   User Decide Login Server Manually
If  your  login  server  IP  address  is  not  available  in  the  “Select  Your 
State”  drop-down  menu 
(1)
,  you  may  manually  enter  the  login 
server  IP  address  by  placing  a  check  in  the  box  next  to  “User 
decide  login  server  manually” 
(4)
and  type  in  the  address  next  to 
“Login  Server” 
(5)
.

Setting Custom Domain Name Server (DNS) Settings
A  “Domain  Name  Server”...

Configuring your WAN Media Access Controller (MAC) Address
All  network  components  including  cards,  adapters,  and  routers,  have 
a  unique  “serial  number”  called  a  MAC  address.  Your  Internet  Service 
Provider  (ISP)  may  record  the  MAC  address  of  your  computer’s  adapter 
and  only  let  that  particular  computer  connect  to  the  Internet  service. 
When  you  install  the  Router,  its  own  MAC  address  will  be  “seen”  by  the 
ISP  and  may  cause  the  connection  not...