BenQ Bl2411pt User Manual

  11   How to assemble your monitor hardware
To Connect the DVI-D Cable
Connect the plug of the DVI-D cable (at the end 
without the ferrite filter) to the monitor video socket. 
Connect the other end of the cable (at the end with the 
ferrite filter) to the computer video socket.
Tighten all finger screws to prevent the plugs from 
accidently falling out during use.
To Connect the DP Cable
Connect the plug of the DP cable to the monitor video 
socket. Connect the other end of the cable to the 
computer...

12  How to assemble your monitor hardware  
4. Connect the power cable to the monitor.
Plug one end of the power cord into the socket labelled 
 on the rear of the monitor. Do not connect the 
other end to a power outlet just yet.
5. Route the cables via the cable clip.
6. Connect-to and turn-on the power.
Plug the other end of the power cord into a power 
outlet and turn it on.
Picture may differ from product supplied for your region.
Switch the power switch next to the AC power input 
jack to ON.
Turn...

  13   How to assemble your monitor hardware
How to detach the stand base
1. Prepare the monitor and area.
Turn off the monitor and the power before unplugging 
the power cable. Turn off the computer before 
unplugging the monitor signal cable.
Protect the monitor and screen by clearing a flat open 
area on your desk and placing a soft item like a towel on 
the desk for padding, before laying the screen face down 
on a flat clean padded surface.
Please be careful to prevent damage to the monitor. Placing...

14  How to assemble your monitor hardware  
Adjusting the monitor height
If you prefer to lower the monitor stand height, push 
the stand downward while holding both left and right 
sides of the monitor.
• Avoid placing hands near the bottom of the monitor stand as 
the descending stand might cause personal injuries. Keep 
children out of reach of the monitor while performing this 
operation.
• If the monitor has been rotated to portrait mode and height adjustment is desired, you 
should be noted that...

  15   How to assemble your monitor hardware
If the height release in the proceeding operation cannot be 
pressed down, press the top of the monitor once as 
illustrated on the right before you proceed.
 

16  How to assemble your monitor hardware  
Rotating the monitor
1. Pivot the display.
Before rotating the monitor with a portrait viewing orientation, the display has to be rotated 90 
degrees.
Right-click the desktop and select 
Screen resolution from the popup menu. Select Portrait in 
Orientation, and apply the setting.
Depending on the operating system on your PC, different procedures should be followed to adjust the screen 
orientation. Refer to the help document of your operating system for...

  17   How to assemble your monitor hardware
Viewing angle adjustment
You may position the screen to the desired angle with -5° to + 20° monitor tilt, 90° (left and 
right total) monitor swivel, and 130 mm monitor height.
4. Adjust the monitor to the desired viewing 
angle.
-5-5O O ~ +20~ +20O-5O ~ +20O-45-45O O ~ +45~ +45O-45O ~ +45O130 mm
 

18  How to assemble your monitor hardware  
Using the monitor wall mounting kit
The back of your LCD monitor has a VESA standard mount with 100mm pattern, allowing the 
installation of a wall mount bracket. Before starting to install a monitor wall mounting kit, 
please read the precautions carefully.
Precautions
• Install your monitor and monitor mounting kit on a wall with flat surface.
• Ensure that the wall material is stable to support the weight of the monitor.
• Turn off the monitor and the power...

  19   Getting the most from your BenQ monitor
Getting the most from your BenQ monitor
To gain the most benefit from your new BenQ LCD monitor, you should install the custom 
BenQ LCD Monitor driver software as provided on the BenQ LCD Monitor CD-ROM.
The circumstances under which you connect and install your BenQ LCD Monitor will 
determine which process you need to follow to successfully install the BenQ LCD Monitor 
driver software. These circumstances relate to which version of Microsoft Windows you...

20  Getting the most from your BenQ monitor  
How to install the monitor on a new computer
This instruction details the procedure for selecting and installing the BenQ LCD Monitor driver 
software on a new computer which has never had a monitor driver installed before. This 
instruction is only suitable for a computer which has never been used before, and for which the 
BenQ LCD Monitor is the first ever monitor to be connected to it.
1.  Follow the instructions in Getting the most from your BenQ monitor...