BenQ Mp720 Dlp Users Manual

							Operation 25
Operation
Start up
1. Plug the power cord into the projector and into 
a wall socket. Turn on the wall socket switch 
(where fitted). Check that the Power indicator 
on the projector lights orange after power has 
been applied.
2. Remove the lens cap. If it is left on, it could 
become deformed due to the heat produced by 
the projection lamp.
3. Press and hold (for 2 seconds) the Power 
button on the remote control or projector to 
start the unit. The Power indicator light flashes 
green and stays green when the unit is on.
The start up procedure takes about 30 seconds 
after pressing Power. In the later stage of start 
up, a default BenQ logo is projected.
(If necessary) Rotate the focus ring to adjust 
the image clearness.
If the projector is still hot from previous activity, it will 
run the cooling fan for approximately 90 seconds before energising the lamp. 
4. If you are prompted for a password, press the arrow buttons to select the four 
password digits, then press Auto. For information about the password function, refer 
to Utilizing the password function on page 25.
5. Switch all of the connected equipment on.
6. The projector will start to search for input signals. The current input source being 
scanned displays at the center of the screen. The search will continue until an input 
source signal is detected.
You can also press Source on the projector or remote control to select your desired 
input signal. For more information, please refer to Switching input signal on page 
29.
If the frequency/ resolution of the input signal exceeds the projector’s operating range, you 
will see the message “Out of Range” displayed on a blank screen.
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an 
option for setting up password security. The password can be set through the on-screen 
menu. For details of the on-screen menu operation, please refer to Using the menus on 
page 32 for information.
WARNING: You will be inconvenienced if you activate the password functionality and 
subsequently forget the password. Print out this manual (if necessary) and write the password 
you used in this manual, and keep the manual in a safe place for later recall.
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation 26
To set a password:
CAUTION: Once a password has been set, the projector cannot be used unless the correct 
password is entered every time the projector is started.
1. Open the on-screen menu and go to  Setting > Password. Select On by pressing 
Left 3or Right4.
2. When the function is activated for the first time, 
a prompt will display on the screen. Use the Up 
5 or Down 6 button to select a number for 
each digit of the password. Use the Left 3 or 
Right4 button to move between the digits of 
the password.
3. When all digits are entered and the password is 
ready, press Auto to confirm. A confirmation message displays.
• The password will display on-screen when being input.
• IMPORTANT: Write your selected password down here in this manual so that it is 
available to you should you ever forget it.
Password: __ __ __ __
Keep this manual in a safe place.
4. Perform one of the following 3 steps.
i. Press Auto to continue. The set-up is finished when the message “Password setup 
completed” displays.
ii. Press Up 5 to go back to the 
previous screen and re-enter four 
digits.
iii. Press Down 6 to cancel the 
password set-up and return to the on-screen menu.
If you forget the password:
You will be asked to enter the four digit password every time you turn on the projector. If 
you enter the wrong password, the password error message displays. You can retry by 
pressing Up 5, pressing Power to turn off the projector and start again, or if you did not 
record the password in this manual, and you absolutely do not remember it, you can use the 
password recall procedure.
To enter the password recall procedure:
Press and hold Right4 for 5 seconds. The projector will display a coded number on the 
screen. Seek help from the local BenQ service center to decode the number. You may be 
required to provide proof of purchase documentation to verify that you are an authorized 
user of the projector.
To change the password:
1. Open the on-screen menu and go to  Setting > Change Password.
2. Press Left 3 or Right4. A “Password Change” message displays.
3. Enter the old password.
i. If the password is correct, you can go on to enter new password.
Password Setup
Enter Password  
Press Auto to Confirm
Press 5 or 6 to change number
Press 3 or 4to move
0000
Password Setup
Do you want to use 0 0 0 0 as your password?
Yes  Auto       No 5       Cancel 6
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation 27
IMPORTANT: Write your selected password down here in this manual so that it is available to 
you should you ever forget it.
Password: __ __ __ __
Keep this manual in a safe place.
ii. If the password is incorrect, a “Password Error” message displays. Press Up 5 to 
try again or press Down 6 to cancel.
4. Check the new password.
i. Pressing Auto completes the procedure. 
ii. Press Up 5 to try again. 
iii. Press Down 6 to cancel the set-up and return to the on-screen menu.
Adjusting the height
The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These 
adjusters change the image height and projection angle. To adjust the projector:
1. Lift the projector up and press the 
adjuster button to release the 
adjuster. The adjuster will drop 
into position and be locked.
Do not look into the lens while the lamp is 
on. The strong light from the lamp may 
cause damage to your eyes.
Be careful when you press the adjuster 
button as it is close to the exhaust vent 
where hot air comes from.
2. Screw the rear adjuster foot to fine 
tune the horizontal angle.
To retract the foot, hold up the projector while pressing the front adjuster button, then 
slowly lower the projector. Screw the rear adjuster foot in a reverse direction.
If the screen and the projector are not perpendicular to each other, the projected image 
becomes vertically trapezoidal. To correct this situation, adjust the value of Keystone in the 
Picture menu, on the projector control panel, or on the remote control. Refer to Correcting 
keystone on page 28 for details.
Auto-adjusting the image
In some cases, you may need to optimize the picture 
quality. To do this, press Auto on the control panel 
of the projector or on the remote control. Within 3 
seconds, the built-in Intelligent Auto Adjustment 
function will re-adjust the values of Frequency and 
Clock to provide the best picture quality. 
The current source information will be displayed at 
the bottom right of the screen for 3 seconds. 
The screen will be blank while Auto is functioning.
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation 28
Fine-tuning the image size and clarity
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the 
top or bottom. It occurs when the projector is not perpendicular to the screen. 
To  c o r r e c t  t h i s ,  b e s i d e s  a djusting the height of the 
projector, you will need to manually correct it 
following ONE of these steps.
1. Press 3 Left/ Right 4 on the control panel of the 
projector to display the status bar labelled Keystone. 
Press Left 3to correct keystoning at the top of the 
image. Press Right4 to correct keystoning at the 
bottom of the image.
2. Press /  on the remote control to display 
the status bar labelled Keystone, then press  to 
correct keystoning at the top of the image or press   to correct keystoning at the bottom 
of the image.
3. Press 6 Menu on the projector or Menu on the remote control. Go to 
 Picture 
--> Ke ystone and adjust the values by pressing Left 3/ Right 4 on the projector or Left 3/ 
Right 4on the remote control.
For example,  1. Adjust the projected image to the size 
that you need using the zoom ring. 2. Then sharpen the image by rotating 
the focus ring. 
0Keystone-6Keystone
0Keystone+6Keystone
1. Press Left 3 on the projector or
2. Press  on the remote control or
3. Press Left 3on the projector or 3 on the 
remote control when you are in Picture --> 
Keystone menu.
1. Press Right 4 on the projector or
2. Press  on the remote control or
3. Press Right
 4 on the projector or 4 on 
the remote control when you are in Picture -
-> Keystone menu.
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation 29
Selecting an application mode
The projector is preset with several predefined 
application modes so that you can choose one to suit 
your operating environment and input source picture 
type. To select a operation mode that suits your need, 
press Mode. The picture modes available for different 
types of signals are shown below. See Application 
Mode on page 33 for details.
Switching input signal
The projector can be connected to multiple devices 
at the same time. However, it can only display one at 
a time. To cycle through the available input sources, 
press the Source button on the projector control 
panel or the remote control. The selected source 
name will display at the center of the screen for 3 
seconds after each button press.
The brightness level of the projected image will 
change accordingly when you switch between 
different input signals. Data (graphic) PC 
presentations using mostly static images are 
generally brighter than Video using mostly moving 
images (movies).
The input type effects the options available for the Application Mode. See Selecting an 
application mode on page 29 for details.
Hiding the image
In order to draw the audience’s full attention to the 
presenter, you can use Blank to hide the screen image. 
Press any key on the control panel to restore the 
image. The word “BLANK” appears at the bottom 
right corner of the screen while the image is hidden. 
When this function is activated with an audio input 
connected, the audio can still be heard. 
You can set the blank time in the 
 Advance 
--> Blank Time 
menu to let the projector return the 
image automatically after a period of time when there 
is no action taken on the blank screen.
Do not block the projection lens from projecting as this could cause the blocking object to 
become heated and deformed or even cause a fire.
PC Signal Input
Brightest Presentation 
(default)sRGB/Photo Gaming Video
YPbPr / S-Video / Video Signal Input
Movie (default) Cinema Gaming Photo
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation 30
Remote paging operations
You can operate your display software program (on a connected PC) which 
responds to page up/down commands (like Microsoft PowerPoint) by 
pressing 
Page Up and Page Dow n on the remote control. See Connecting 
a computer on page 18 for details. 
Connect the projector to your PC or notebook with a USB cable prior to 
using this function. 
Freezing the image
Press the Freeze button on the remote control to freeze the image. An icon 
 will display in the lower right corner of the screen. To release the 
function, press the Freeze button on the remote control, or the Source 
button on the projector control panel. Note that pressing the Source 
button will also change the input source.
Even if an image is frozen on the screen, the pictures are running on the 
video or other device. If the connected devices have active audio output, 
you will still hear the audio even though the image is frozen.
Shutdown
1. Press Power and a prompt message 
appears. Press Power a second time 
to turn the projector off. 
2. The Power indicator light flashes 
orange and the lamp shuts down, 
the fans continue to run for 
approximately 90 seconds to cool 
down the projector.
• To protect the lamp, the projector will 
not respond to any commands 
during the cooling process.
• To shorten the cooling time, you can also activate the Quick cooling function. See 
Quick Cooling (off) on page 36 for details.
3. Disconnect the power cord from the wall 
socket.
• Do not unplug the power cord before the 
projector shutdown sequence is complete or 
during the 90-second cooling down process.
• If the projector is not properly shut down, you 
risk damaging the lamp. Do not move the 
projector whilst the lamp is hot.
  SWAP
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation 31
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type 
selected.
*When a Video or S-Video signal is connected, the function is only available with NTSC 
system selected.
Functions available when receiving different signal types...
Sub-MenuPC / DVI-AWireless / 
DVI-DVideo / S-
VideoComponent 
Video 
Picture
Application Mode
Keystone
Color Temp
Brightness
ContrastApplication Mode
Keystone
Color Temp
Brightness
Contrast
Color
Tint*
Pro-Picture
Auto Resize
Aspect Ratio
H Position
V Position
Phase
H. SizeAuto Resize (not 
available with 
Wireless 
selected)
Aspect RatioAuto Resize
Aspect Ratio
Sharpness
Setting
Mute
Vo lu m e
OSD Time
Quick Cooling
Password
Change Password
Reset
Advance
Mirror
Blank Time
Source Scan
Language
Splash Screen
High Altitude Mode
Auto Off
Economic Mode
Information
Source
Resolution
Application Mode
Equivalent Lamp HourSource
System
Application 
Mode
Equivalent Lamp 
HourSource
Resolution
Application 
Mode
Equivalent Lamp 
Hour
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation 32
Using the menus
The projector is equipped with on-screen display (OSD) menus for making various 
adjustments and settings.
There are 17 different menu languages. (Refer to page 4. Advance menu on page 37 for 
more details.)
The following example describes the adjustment of the keystone.
1. Press 6 Menu on the projector or Menu 
on the remote control to turn the on-
screen menu on.4. Adjust keystone values by 
pressing 3/ 4on the projector 
or remote control.
2. Use 3 / 4 on the projector or remote 
control to select the   Picture 
menu.
3. Press 5Exit / 6Menu on the projector 
or 6 / 5 on the remote control to select 
Keystone.5. Press5Exit on the projector 
repeatedly or press Menu on the 
remote control to leave and save 
the setting.
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation 33
1. Picture menu
Some picture adjustments are available only when certain input sources are in use. 
Unavailable adjustments are not shown on the screen.
FUNCTION 
(default setting 
/ value)
DESCRIPTION
Application 
Mode
(PC: 
Brightest;
YPbPr/ S-
Video/ Video: 
Movie)
Pre-defined application modes are provided so you can optimize your 
projector image set-up to suit your program type.
You can use the remote control Mode button to select a predefined 
application mode. See Selecting an application mode on page 29 
for details.
PC Signal Input
1.Brightest Mode: Maximizes the brightness of the projected image. 
This mode is suitable for environments where extra-high 
brightness is required, such as using the projector in well lit 
rooms.
2.Presentation Mode (Default): Is designed for presentations. The 
brightness is emphasized in this mode to match PC and notebook 
coloring.
3.sRGB/Photo Mode: Maximizes the purity of RGB colors to 
provide true-to-life images regardless of brightness setting. It is 
most suitable for viewing photos taken with an sRGB compatible 
and properly calibrated camera, and for viewing PC graphic and 
drawing applications such as AutoCAD.
4.Gaming Mode: Is suitable for playing PC-based games in a bright 
living room.
5.Video Mode: Is appropriate for playing movies, video clips from 
digital cameras or DVs through the PC input for best viewing in a 
blackened (little light) environment.
YPbPr/ S-Video/ Video Signal Input
1.Movie Mode (Default): Is suitable for enjoying colorful movies 
and TV in a home darkened (not bright) lounge room lighting 
level environment. 
2.Cinema Mode: Is suitable for enjoying DVD movies best viewed in 
a blackened (little light) home cinema or lounge room 
environment.
3.Gaming Mode: Is suitable for playing gamebox-based video games 
in a normal living room lighting level environment.
4.Photo Mode: Is perfect for viewing digital photos taken in daylight 
with an sRGB compatible and properly calibrated camera, and for 
viewing Photo CDs. The color saturation and brightness are well-
balanced.
Keystone (0)Corrects any keystoning of the image. Refer to Correcting keystone on 
page 28 for more information.
Downloaded From projector-manual.com BenQ Manuals 
						

							Operation 34
Color Temp 
(depends on 
the selected 
Application 
mode)
There are four color temperature* settings are available.
1.T1: With the highest color temperature, T1 makes the image 
appear the most bluish white than other settings.
2.T2: Makes images appear bluish white.
3.T3: Maintains normal colorings for white.
4.T4: Makes images appear reddish white.
*About color temperatures:
There are many different shades that are considered to be “white” for 
various purposes. One of the common methods of representing white 
color is known as the “color temperature”. A white color with a low color 
temperature appears to be reddish white. A white color with a high color 
temperature appears to have more blue in it.
Brightness 
(depends on 
the selected 
input source)
Adjusts the brightness of the image. The higher the value, the brighter 
the image. And lower the setting, darker the image. Adjust this control 
so the black areas of the image appear just as black and that detail in the 
dark areas is visible. 
Contrast 
(depends on 
the selected 
input source)
Adjusts the degree of difference between dark and light in the image. 
The higher the value, the greater the contrast. Use this to set the peak 
white level after you have previously adjusted the Brightness setting to 
suit your selected input and viewing environment. 
Color 
(depends on 
the selected 
input source)Increases or decreases the color intensity of the image.
Tint (50)
Adjusts the color tones of the image. The higher the value, the more 
greenish the image becomes. The lower the value, the more reddish the 
image becomes.
When a Video or S-Video signal is connected, the function is only 
available with NTSC system selected.
50-30+70
-30
50+70
Downloaded From projector-manual.com BenQ Manuals