Home > Bersa > Firearms > Bersa_Mini Thunder 45 Instructions Manual

Bersa_Mini Thunder 45 Instructions Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Bersa_Mini Thunder 45 Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 3 Bersa manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							11
    SAFETY WARNING: All owners and users of FIRESTORM pistols are reminded to use the decocking
    lever to decock their pistols. This is the only way to safely lower the hammer.
    Warning:
    The hammer should never be manually lowered by pulling the trigger. Manually lowering the hammer is
    dangerous and may result in severe personal injury or death.
    WARNING: DO NOT THUMB THE HAMMER DOWN. This action may result in severe per
    sonal injury or death. ALWAYS USE THE DECOCKING LEVER.
    Firing:
    If you intend to fire your pistol, push down the manual safety lever and squeeze the trigger.
    Since the hammer is uncocked, the pull on the trigger will first cock the hammer and then release it. This
    firing mode is called double action.
    The discharge will recoil the slide which, in turn, will eject the fired cartridge case, cock the hammer, and
    activate the recoil spring. The slide then automatically returns forward feeding the next cartridge from the
    magazine into the chamber. THE PISTOL THEN IS READY TO FIRE AGAIN.
    Squeeze the trigger to fire again.
    To fire the first shot by the single action mode, simply cock the hammer manually after disengaging the
    safety and squeeze the trigger. 
    						
    							12
    When the last round has been fired, the slide remains fully back. If you intend to fire again, remove the
    empty magazine and insert a loaded one. Press the slide catch (Fig. 4) to close the slide and load the
    chamber.
    CAUTION: Always keep your finger off the trigger whenever you do not intend to fire.
    Safety Key:
    Your pistol is provided with an internal locking system operated by a special key. It is located above the
    trigger in the left side of the frame. In the unlocked position (F) the pistol is ready to fire. In the locked
    position (S) you can not cock the hammer, fire in double action, load a catridge in the chamber
    or disassemble the pistol. Please make sure that your pistol is in the lock position (S) when not in use.
    Always store and keep your pistol unloated and in a safe place away from minors. Replacement keys
    can be ordered by calling customer service at 1-732-493-0333.
    Unloading the pistol and chambered cartridge:
    Press the magazine release button and then grasp the serrated sides of the slide from the rear and
    draw the slide fully rearward in order to extract any cartridge from the barrel chamber.
    When sure the chamber is empty and the cartridge has been ejected, release the slide.
    How to reverse the magazine release button: After removing the magazine, unscrew and remove the 
    						
    							13
    pin of the grip. Remove the grip. Repeat the same procedure with the pin of the magazine release button
    (Fig. 6) until it is dropped out. Put the magazine release button in the place of your preference following the
    above procedures in reverse order. Then screw back the pin of the grip and reassemble it.
    MAINTENANCE
    It is recommended to clean and lubricate the pistol every time it is fired.
    Field Stripping
    Make sure the pistol is unloaded.
    Depress the magazine release button and remove the magazine. With right thumb rotate disassembling
    latch until it stops (Fig. 7). Pull forward the slide-barrel assembly with recoil spring and spring guide (Fig.
    8). Slightly pressing the recoil spring guide head, lift the recoil spring guide (Fig. 9 and 10). Take out the
    barrel from the slide
    No further disassembly is recommended unless done by a competent gunsmith.
    Cleaning and lubricating: After dismantling, clean the barrel and chamber with a light film of high quality
    gun oil to clean all exposed internal surfaces. Put special attention on the bolt face (where the firing pin 
    						
    							14
    protrudes) and under the extractor hook. Lubricate moving parts sparingly with a light high quality gun oil.
    Wipe off any excess oil.
    Assembly:
    Assemble following the Field Stripping procedure in reverse order. It is advisable to pay attention to the
    following points:
    The recoil spring guide head should lodge in the center of its groove in the barrel base.
    When rotating the disassembling latch, the slide should be in the closed position 
    						
    							15
    References:FIG. 1
    FIG. 2
    FIG. 3
    FIG. 4
    FIG. 5
    FIG. 6
    FIG. 7
    FIG. 8
    FIG. 9
    FIG. 10 
    						
    							16
    SAFETY WARNINGSEar and eye protection: Use ear plugs or earmuff-type protectors to guard you against cumulative,
    permanent hearing loss as a result of continuous exposure to shooting noise.
    Shooting glasses will guard you against powder, gas, carbon residue, lubricant, metallic particles or
    similar debris that may emanate occasionally from any firearm in normal use
    Always make sure that anyone near you is also wearing ear and eye protection.
    Safety mechanism:
    1.Your firearm has an effective, well-designed safety mechanism. However, there’s no safety mecha
    nism capable of substituting your common sense and good safety procedures. No safety can
    guard you against horseplay, carelessness, or improper use. It may become ineffective by break
    age or malfunction due to abusive use, incorrect assembly, or unauthorized adjustments.
    2.While handling any firearm, never allow it to point at any part of your body or at another person.
    No harm should result if you obey this rule, even if an accidental discharge occurs.
    3.The safety mechanism should be on until you are actually aiming at the target ready to shoot
    4.When turning the safety ON or OFF, point the muzzle in a safe direction and keep your finger off
    the trigger.
    5.Be sure to put the safety in the correct position or it will not be effective. Some firearms have a red
    warning dot next to the safety which should be totally covered when the safety is on.
    6.Do not carry the firearm loaded without the safety on (Double action revolvers and some double
    action pistols have an automatic internal safety mechanism instead of a manual one). 
    						
    							17
    Loading:
    1.Be sure the muzzle is pointing in a safe direction when loading the firearm
    2.Do not load or unload a firearm in a confined space such as a vehicle or building other than a
    well-constructed shooting range. In an enclosed area there is not usually a safe direction in which
    to point the firearm, and if accidentally fired, there is a great risk of causing personal injury or
    property damage.
    3.Clean all oil and grease from the chamber before loading, and be sure nothing is obstructing the
    barrel. Any obstruction in the barrel may cause the barrel to bulge or burst when firing it, or
    otherwise damage the firearm or injure the shooter and bystanders.
    Firing:
    1.When cocking a firearm, keep your finger off the trigger and point the muzzle in a safe direction.
    2.Never carry a cocked firearm around or leave it unattended! A cocked firearm will fire with the
    slightest pressure on the trigger. If you fall or the firearm is dropped, or someone hits it, an acci
    dental firing may occur.
    3.When firing a semi-automatic gun, keep your fingers, hand, face and all other parts of your body
    away from the ejection port, or any other part of the slide (or bolt) when it is moving. The shooter
    will not be injured if the firearm is held and fired at arm’s length.
    4.Be sure no one is standing where they may be struck by an empty cartridge case. Ejected cases
    are hot and may cause burns, cuts or eye injuries (if no eye protection is worn). Be sure there is 
    						
    							18
    a clear, safe, unobstructed path for fire cases to be ejected. And also be sure they will not bounce
    off a hard object and hit someone.
    5.If your firearm has a mechanical malfunction while shooting, or if powder or gas emanates from it,
    or if a cartridge case is bulged or ruptured, or if the sound of the fire is not quite right, DO NOT
    CONTINUE SHOOTING. STOP IMMEDIATELY AND UNLOAD THE FIREARM. Then take the
    firearm and ammunition to your gunsmith.
    6.A loaded cartridge case that becomes jammed in a semiautomatic gun between the slide (or bolt)
    and the barrel may be removed as follows: Keep the muzzle pointed in a safe direction. First,
    remove the magazine, and then pull the slide or bolt back. Hold it or lock it to the rear. Remove
    the jammed case by shaking the firearm or pick it out with your fingers.
    Unloading:
    1.Be sure the muzzle is pointed in a safe direction.
    2.After removing the magazine, be sure to clear the chamber
    3.Do not assume a firearm is unloaded until you have visually checked it.
    Transporting and storing your firearm:
    1.Always keep your firearm unloaded when transporting it to and from shooting activities.
    2.Store firearms and ammunition separately, preferably locked and secured. Keep firearms and
    ammunition out of reach of children, untrained individuals or careless, unauthorized adults. 
    						
    							19
    Semi-automatic pistols:
    1.Carrying a semi-automatic pistol with a cartridge in the chamber greatly increases the chances of
    accidental firing. Doing so may only be justified in cases of clear and present danger. For in
    stance, in cases of self-defense you may have to fire your pistol instantly, however this is not
    recommended. The safest way to carry a loaded pistol is to have the chamber empty.
    2.If you MUST carry a semi-automatic pistol with a cartridge in the chamber, be sure the hammer is
    decocked. If your pistol has a hammer lowering lever, use this lever instead of the trigger to lower
    the hammer. And also, if your pistol has a manual safety, always leave it on when carrying the
    pistol with a cartridge in the chamber until the firearm is aimed at the target ready to shoot.
    Ammunition:
    1.Use high-quality, original, factory-manufactured ammunition in your firearm. Never use
    ammunition that is wet, dirty, corroded or damaged. Never oil or lubricate ammunition or let
    excess aerosol lubricants, preservatives, or cleaners come into contact with cartridges. This may
    cause dangerous malfunction problems. Be sure your ammunition has the proper caliber, which
    is engraved on the firearm. Do not use ammunition of any other caliber.
    2.Reloading ammunition is a science. Improperly loaded ammunition may cause severe damage to
    your firearm and severe injury to both the shooter and other individuals. Use ammunition ap proved by
    the U.S. Sporting Arms and Ammunition Manufacturers’ Institute, Inc. (SAAMI). All warranties are void if
    you use reloaded, “remanufactured”, handloaded, or other non-standard ammunition. 
    						
    							20
    3.Excessive pressure inside the chamber or the barrel may cause severe damage to the firearm
    and/or severe injury to the shooter. This may be caused by obstructions in the barrel, propellant
    powder overloads, or the use of incorrect, wrongly assembled, dirty, corroded or damaged
    cartridges.
    4.Stop shooting IMMEDIATELY and check the barrel for obstructions if:
    - you have difficulties in chambering a cartridge or feel unusual resistance
    -a cartridge misfires
    -a fired cartridge case is not extracted
    -you see unburned grains of powder in the mechanism
    -a shot sounds abnormal or weak
    Dirty, corroded, oil hambered completely, and the cartride case may burst when firing.
    8.Wipe any oil preservative from the chamber before shooting and do not lubricate the cartridges.
    Lubricants interfere with the required friction between the cartridge case and the chamber wall.
    This causes stress similar to excessive pressure.
    9.Do not use too much lubricant on your gun’s moving parts. Do not spray gun care aerosol
    products where they may come into contact with ammunition. Do not overspray. Lubricants,
    especially aerosol sprays, may penetrate cartridge primers and cause the ammunition to misfire.
    Some lubricants may get inside cartridge cases and prevent powder from igniting. If only the
    primer ignites, the bullet may become lodged in the barrel. 
    						
    All Bersa manuals Comments (0)

    Related Manuals for Bersa_Mini Thunder 45 Instructions Manual