Bisell BISSELL Deluxe with HeatWave Technology 32788 User Manual

							Maintenance & Care
machine storage
Put u\fit awa\b i\f a closet or baseme\ft for \fext 
use. store clea\fer i\f a protected, dr\b area.  si\fce 
this product uses water, it must \fot be stored 
where there is a da\fger of freezi\fg. Freezi\fg will 
damage i\fter\fal compo\fe\fts a\fd void guara\ftee.
brush belt and brush removal & replacement 
Occasio\fal replaceme\ft of the brush belt or 
brush ma\b become \fecessar\b.  if \feeded, please 
follow i\fstructio\fs below. 
1.	 Tur\f off machi\fe a\fd u\fplug it from outlet. 
Wrap hose a\fd cord o\f racks.
2.	 Remove 2-i\f-1 water ta\fk a\fd set aside.
3.	 ImpoRtant : fully recline handle and turn   
unit upside down\f 
4.	 locate red belt access door a\fd remove   
two screws. 
notE:  the dark screw is a long machine screw 
and will take approximately \b5 full turns to 
completely remove\f  the head of the screw will 
lift from the belt access door so that it can be 
easily removed\f
5.	 Remove belt access door assembl\b from e\fd 
of brush a\fd set aside. 
6.	 Remove brush belt.  if wor\f or damaged, 
replace with \few brush belt.
7. 	if \fecessar\b, the brush roll ca\f be removed   
for clea\fi\fg or replaceme\ft. To remove, rotate 
the brush out of brush housi\fg a\fd pull brush 
off axle attached to remai\fi\fg e\fd cap. The 
remai\fi\fg pivot arm ca\f be removed b\b taki\fg 
out the screw (this will allow for full access to 
brush chamber for clea\fi\fg). Make sure “ke\bed” 
e\fd of metal rod is alig\fed with slot i\f pivot arm 
before re-assembli\fg. Replace brush o\f axle, 
cogged-side last. You ma\b \feed to rotate brush 
to allow it to slide all the wa\b dow\f the axle. 
8.	 Reattach brush belt b\b i\fstalli\fg it o\fto   
toothed pump pulle\b a\fd the\f o\fto toothed   
e\fd of brush.
9. 	Reattach belt access door assembl\b   
to e\fd of brush a\fd rotate back i\fto place. 
Replace screws.  
notE: Do not over tighten screws\f
if \bou have a\f\b questio\fs or are havi\fg trouble 
removi\fg, replaci\fg or rei\fstalli\fg \bour brush belt 
or brush, please call  bissell Co\fsumer Care.
   
   www.
bissell.com11
WaRnInG
To reduce the risk of electric shock, push power button  off and disconnect plug from electrical outlet before 
performing maintenance or troubleshooting checks.
\b\f 3\f
23
45
6
5\f
6\f 4\f 
						

							pump belt removal & replacement
Occasio\fal replaceme\ft of the pump belt ma\b 
become \fecessar\b.  if \feeded, please follow 
i\fstructio\fs below. 
1.	 Tur\f off machi\fe a\fd u\fplug it from outlet. 
Wrap hose a\fd cord o\f racks.
2.	 Remove 2-i\f-1 water ta\fks a\fd set aside.
3.	 iMPORTANT: Full\b recli\fe ha\fdle a\fd tur\f   
u\fit upside dow\f.
4.	 locate red belt access door a\fd remove   
two screws.
notE:  the dark screw is a long machine screw 
and will take approximately \b5 full turns to 
completely remove\f  the head of the screw will 
lift from the belt access door so that it can be 
easily removed\f
5.	 Remove belt access door assembl\b from e\fd 
of brush a\fd set aside.
6.	 Remove brush belt from e\fd of brush a\fd 
set aside.  if wor\f or damaged, replace with \few 
brush belt.
7. 	Remove pump belt a\fd replace it with a \few 
belt b\b pi\fchi\fg belt at o\fe e\fd to make a large 
loop. Attach belt to silver motor shaft first a\fd 
the\f pull towards larger, red pulle\b. Attach belt 
to red pulle\b. 
notE:  Spinning the red pulley a few times will 
help center belt and ensure correct assembly\f
8.	 Reattach brush belt b\b i\fstalli\fg o\fto   
toothed pump pulle\b a\fd the\f o\fto toothed   
e\fd of brush.
9. 	Reattach belt access door assembl\b   
to e\fd of brush a\fd rotate back i\fto place.   
Replace screws.
notE: Do not over tighten screws\f
if \bou have a\f\b questio\fs or are havi\fg trouble 
removi\fg, replaci\fg or rei\fstalli\fg \bour brush 
belt, please call  bissell Co\fsumer Care.
Maintenance & Care
www.bissell.com
      12
WaRnInG
To reduce the risk of electric shock, push power button  off and disconnect plug from electrical outlet before 
performing maintenance or troubleshooting checks.
\b\f 3\f
23
45
67
89
5\f
7\f
9\f
4\f
6\f
8\f 
						

							Troubleshooting
problempossible causes Remedies
Reduced 
spray oR  
no spray bladder ma\b be empt\b.
Press power pedal 
 off; refill 
 
bladder with clea\f ha\fd hot 
(60°F/140°C MAX) tap water a\fd 
formula.
2-i\f-1 ta\fk ma\b \fot be seated 
properl\b. Press power pedal 
 
off; remove 
ta\fk a\fd reseat ta\fk. 
Pump ma\b have lost prime. Press power pedal 
 off; after 1 mi\f-
ute tur\f o\f a\fd depress spra\b trigger.
Pump belt ma\b be broke\f. Press power pedal 
 off a\fd u\fplug 
from outlet. Follow belt replaceme\ft 
i\fstructio\fs o\f pages 11 a\fd 12.
Dirtlifter 
p owerbrush 
does not turn brush belt or pump belt is 
 
off or broke\f. Press power pedal  
off a\fd u\fplug 
from outlet. Follow belt replaceme\ft 
i\fstructio\fs o\f pages 11 a\fd 12.
cleaner   
not picking 
up solution Read\bTools dial ma\b be o\f wro\fg 
setti\fg for clea\fi\fg job. 
set Read\bTools dial to either floor 
clea\fi\fg or tools.
Poor tool positio\f. (Ha\fd held 
attachme\fts o\fl\b). Adjust a\fgle; appl\b more dow\fward 
pressure.
Removable \fozzle ma\b \fot be 
properl\b attached. Make sure \fozzle is o\f correctl\b b\b 
slightl\b raisi\fg fro\ft of machi\fe to 
li\fe up slots o\f each side of base of 
machi\fe with hooks o\f each side of 
\fozzle. Attach at base first a\fd the\f 
click \fozzle i\fto place. Refer to image 
6 o\f page 8.
2-i\f-1 ta\fk lid is \fot properl\b i\fstalled.Re-i\fstall lid; refer to images o\f page 7. 
2-i\f-1 ta\fk is \fot properl\b seated.
2-i\f-1 ta\fk must be firml\b seated to 
fu\fctio\f; remove a\fd reseat 2-i\f-1 ta\fk. 
2-i\f-1 ta\fk has picked up   
maximum dirt\b water. empt\b 2-i\f-1 ta\fk a\fd refill, refer to 
the Operatio\f sectio\f.
The li\ft scree\f ma\b be clogged. Clea\f out li\ft scree\f, refer to page 8.
Other mai\fte\fa\fce or service \fot i\fcluded i\f the ma\fual should   
be performed b\b a\f authorized service represe\ftative.
Tha\fk \bou for selecti\fg a  bissell product.
please do 
not return 
this product 
t o   t h e   s t o r e \f              
      www.
bissell.com13
WaRnInG
To reduce the risk of electric shock, push power button  off and disconnect plug from electrical outlet before 
performing maintenance or troubleshooting checks.  
						

							www.bissell.com
      14
Replacement Parts
These items are available for your BI\f\fELL dee\b cleaner. Visit www.BI\f\fELL.com
pArt #pArt nAme pArt #pArt nAme
160-3026 Tank Assembly Complete
160-3027 Tank Base
160-2858Removable Nozzle160-1543 Replacement Pump Belt (with 
instructions)
160-1542Replacement Brush Belt (with 
instructions)160-1526 Tank Top (with Handle)
160-1519 Upper Hose and Cord Rack160-1520 Lower Hose and Cord Rack
160-1537Brush Roll Assembly   
with Pivot Arms
*Not all parts are included with every model.  
						

							Accessories
These items are available for your BI\f\fELL dee\b cleaner. Visit www.BI\f\fELL.com   
   www.
bissell.com
pArt # pArt nAme pArt #pArt nAme
160-1523 Hard Floor Tool
203-6651 3" Tough Stain Tool
203-66534" Upholstery Tool203-6654 6" Stair Tool
203-6652Powered TurboBrush™ Tool203-0116 Spraying, 2-in-1 Crevice Tool 
w/ Brush
203-6655Spraying Crevice Tool203-7412 Deep Reach Tool
15
*Not all parts are included with every model.
cleaning  formula: Refer to bottom of page 5 of this guide for a full selection of cleaning 
formula available for purchase\f 
						

							©2013 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 160-3040  Rev 01/14 RevA
Visit our website at: www.BISSELL.com
Scotchgard is a trademark of 3M
Microban® is a registered trademark of Microban Products Company 
16
Consumer Guarantee 
This Guarantee only applies outside of the USA and Canada. It is 
provided by BISSELL International Trading Company BV (“BISSELL”).
This Guarantee is provided by BISSELL. It gives you specific rights. 
It is offered as an additional benefit to your rights under law. You 
also have other rights under law which may vary from country 
to country. You can find out about your legal rights and remedies 
by contacting your local consumer advice service. Nothing in this 
Guarantee will replace or lessen any of your legal rights or remedies.  
If you need additional instruction regarding this Guarantee or have 
questions regarding what it may cover, please contact BISSELL 
Consumer Care or contact your local distributor. 
This Guarantee is given to the original purchaser of the product from 
new and is not transferable. You must be able to evidence the date 
of purchase in order to claim under this Guarantee.
limited two- year Guarantee
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, 
BISSELL will for two years from the date of purchase by the  
original purchaser repair or replace (with new or remanufactured 
components or products), at BISSELL’s option, free of charge, any 
defective or malfunctioning part or product.
BISSELL recommends that the original packaging and evidence of   
the date of purchase be kept for the duration of the Guarantee 
period in case the need arises within the period to claim on the 
Guarantee. Keeping the original packaging will assist with any 
necessary re-packaging and transportation but is not a condition   
of the Guarantee.
If for your product is replaced by BISSELL under this Guarantee, 
the new item will benefit from the remainder of the term of this 
Guarantee (calculated from the date of the original purchase).  
The period of this Guarantee shall not be extended whether or  
not your product is repaired or replaced.
*EX cEptIonS anD EX clUSIonS fRom  
tHE tERmS of tHE GU aRantEE
This Guarantee applies to products used for personal domestic use and 
not commercial or hire purposes.  Consumable components such as 
filters, belts and mop pads, which must be replaced or serviced by the 
user from time to time, are not covered by this Guarantee.  
This Guarantee does not apply to any defect arising from fair wear 
and tear. Damage or malfunction caused by the user or any third 
party whether as a result of accident, negligence, abuse, neglect, or 
any other use not in accordance with the User Guide is not covered 
by this Guarantee. 
Visit the  bISSEll website: www\fbISSEll\fcom
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: _____________ Please record your Purchase Date: _____________
NOTE:	Please	\beep	your	original	sales	receipt.	It	provides	proof	of	the	date		
of	purchase	in	the	event	of	a	Guarantee	claim.	See	Guarantee	for	details.
An unauthorised repair (or attempted repair) will void this Guarantee 
whether or not damage has been caused by that repair/attempt.
Removing or tampering with the Product Rating Label on the   
product or rendering it illegible will void this Guarantee. 
SAVE AS SET OUT BELOW BISSELL AND ITS DISTRIBUTORS ARE NOT 
LIABLE FOR ANY LOSS OR DAMAGE THAT IS NOT FORESEEABLE 
OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY 
NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT INCLUDING 
WITHOUT LIMITATION LOSS OF PROFIT, LOSS OF BUSINESS, BUSINESS 
INTERRUPTION, LOSS OF OPPORTUNITY, DISTRESS, INCONVENIENCE OR 
DISAPPOINTMENT.  SAVE AS SET OUT BELOW BISSELL’S LIABILITY WILL 
NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
BISSELL  DOES NOT EXCLUDE  OR LIMIT  IN ANY  WAY  ITS LIABILITY  FOR 
( A )  DEATH  OR PERSONAL  INjURY CAUSED  BY OUR  NEGLIGENCE  OR THE  
NEGLIGENCE  OF OUR  EMPLOYEES,  AGENTS OR SUBCONTRACTORS; (B ) 
FRAUD  OR FRAUDULENT  MISREPRESENTATION; ( C) OR  FOR  ANY  OTHER  
MATTER  WHICH CANNOT  BE EXCLUDED  OR LIMITED  UNDER LAW.
Consumer Care
If	your	 \fISSELL	 product	should	require	
service	 or	to	claim	 under	 our	Limited 	
Two-Year	 Guarantee,	 please	visit:
Website or E-mail:www.bissell.com
for UK inquiries: Telepho\fe: 0844.888.\a6644
Mo\fda\b – Thursda\b 9am - 5pm
Frida\b 9am - 4pm
bissell Homecare (Overseas) i\fc.
Grou\fd Floor
226 berwick Ave\fue
slough, 
berkshire, sl1 4QT
U\fited Ki\fgdom
Febreze is a trademark of The 
Proctor & Gamble Company, 
Cincinnati, Ohio used under 
license by BISSELL Homecare, Inc.