Bose CineMate digital home theatre speaker system Sold from September 2005 User Manual

							OPERATION
21
2SHUDWLRQIP O
PERATION
English FrançaisEspañol
Verifying a device code
When you programmed your remote during setup, a device code for each source was stored 
in the remote. If you need to verify which code has been programmed for a particular source, 
follow the steps below. 
If you need to reprogram a device code, see “Setting up the remote to control other sources” 
on page 14.
1.Press and hold Setupuntil all five source buttons light up (about three seconds).
2.Press the source button of the device you want to verify (TV, CBL-SAT, DVD, VCR, or 
AUX). Only the selected source button will remain lit.
3.Press Info.
4.Press 1 on the remote and count the number of times the five source buttons blink 
(zero is indicated by a long blink). This is the first digit.
5.Press 2 on the remote and count the number of times the five source buttons blink 
(zero is indicated by a long blink). This is the second digit.
6.Press 3 on the remote and count the number of times the five source buttons blink 
(zero is indicated by a long blink). This is the third digit.
7.Press 4 on the remote and count the number of times the five source buttons blink 
(zero is indicated by a long blink). This is the fourth digit.
8.Press 5on the remote and count the number of times the five source buttons blink 
(zero is indicated by a long blink). This is the fifth digit.
9.Press Exit. 
						

							22
CARE AND
 M
AINTENANCE
English Français Español
CARE AND MAINTENANCE
Cleaning your speaker system
• You may clean the surface of your speakers, Acoustimass® module, and Interface module 
with a soft, damp cloth. You can use an ammonia-free window cleaner on a soft cloth to 
maintain the finish.
• Do not use any sprays near the speakers. Do not use any solvents, chemicals, or cleaning 
solutions containing alcohol, ammonia, or abrasives.
• Do not allow liquids to spill into any openings.
• The speaker grilles require no special care, although you may vacuum them carefully, 
if necessary.
Limited warranty
The CineMate™ speaker system is covered by a limited transferable warranty. Details of the 
warranty are provided on the product registration card that came with your system. Please fill 
out the information section on the card and mail it to Bose.
Accessories
The CineMate speakers are compatible with Bose® mounting accessories, including the 
UB-20 wall brackets, UFS-20 floor stands, and UTS-20 table stands. Bose also offers cable 
adapters, for use in running speaker cable through walls, and longer speaker wire, as needed. 
For further information or to order mounting brackets, stands, or cable adapters, contact your 
Bose dealer. Or, to call Bose directly, refer to the address sheet included in the carton. 
Troubleshooting
Problem What to do
No power, no 
LEDs• Make sure the Acoustimass
® module power switch (230V units only) is turned on. 
• Make sure the power cord is inserted securely into the Acoustimass module and plugged firmly 
into an operating AC wall outlet (mains).
• Make sure the Interface module is plugged into the Acoustimass module properly.
• Unplug the Acoustimass module power cord from the AC wall outlet for one minute, then recon-
nect it. This allows the unit to reset itself. Check that the red Standby LED on the front of the 
Interface module is now lit.
No sound • Make sure the CineMate speaker system is turned on. The green LED on the front of the Inter-
face module should be lit.
• Increase the volume.
• Check to see if the sound source is muted. Press the remote control Mute button to unmute it.
• Make sure the Interface module and speaker cables are both firmly connected to the jacks on 
the Acoustimass module.
• Check the speaker connections.
• Unplug the power cord from the outlet for one minute, then reconnect it. This allows the system 
to reset itself.
• Check that the correct TV/Video input has been selected. See “Selecting the TV input” on 
page 16.
• Check the connections from the Interface module to the TV or other source.
• Check that the TV’s audio output is enabled. See your TV owner’s guide for information.
• If the TV’s audio output is VARIABLE (VAR), make sure the TV’s internal speakers are turned off 
and the TV volume is turned up. 
						

							CARE AND
 M
AINTENANCE
23
CARE AND MAINTENANCE
English FrançaisEspañol
Customer service
For additional help in solving problems, contact Bose® Customer Service. Refer to the 
address sheet included with the system.
Technical information 
Sound but no 
picture• Make sure the TV is turned on.
• Check that the correct TV/Video input is selected. See “Selecting the TV input” on page 16.
Remote control is 
inconsistent or 
does not work• Check the battery to be sure it is installed properly.
• Point the remote control at the Interface module.
• Relocate the Interface module, making sure it is in a clear line of sight to the remote and there 
are no obstructions.
• Make sure the protective film is removed from the lens on the front of the Interface module.
• Check that the source button on the remote blinks when a button is pressed.
• Check that the green LED on the Interface module blinks off briefly when a remote button is 
pressed.
• Check that a device code has been programmed for the selected source. See “Verifying a device 
code” on page 21. 
• There may be more than one device code for your brand of device. Find your device and brand 
in the CineMate
TM Universal Device Codes book. Try programming another code, then check the 
device for improved functionality.
Sound is distorted • Make sure speaker cables are not damaged and the connections are secure.
• Reduce the audio output level from the TV connected to the Interface module.
Sound is coming 
from the TV• Turn off your TV’s internal speakers. See “Turning off the TV internal speakers” on page 13.
• Turn down the TV volume. Problem What to do
Power rating
USA/Canada: 120V  60Hz 300W
International: 220-240V  50/60Hz 300W
Dual voltage: 115/230V  50/60Hz 300W
Source inputs
TV AUDIO
Dimensions
Speakers:
3
1/2"H x 77/8"W x 51/4"D
(8.7 cm x 19.9 cm x 13.6 cm)
Acoustimass
® module:
14
1/2"H x 83/4"W x 191/8"D
(36.7 cm x 22.2 cm x 48.5 cm)Weight
Speakers: 2.7 lb (1.2 kg) each
Acoustimass module: 23.3 lb (10.6 kg)
Finish
Speakers: polymer
Acoustimass module: polymer