Boxlight Projectowrite 2 User Manual

							8
Part Names
Rear
A  MOUSE
Connect a USB mouse cable to a computer  
to control computer mouse functions.
B  RS232
Serial data port for controlling the projector  
with  a  computer  or  other  RS-232  control 
device.
C  AUDIO IN 1 & D AUDIO IN 2
Mini  jack  port  corresponds  to  computer  
input.
E  AUDIO OUT
F  RGB IN
Input  analog  RGB  video  signal  from  a  
computer.
G  RGB OUT
C o n n e c t   a n   e x t e r n a l   m o n i t o r   t o   t h i s  
connection to view the RGB IN input.
H  DVI-I IN
Input digital DVI-I signal from a computer.
 I  S-VIDEO
S-Video signal from a video source.
 J  VIDEO
Composite video signal from a video  
source.
 K  AUDIO IN 3, R / L
RCA type corresponds to video input.
 L  COMPONENT /Y, Pb, Pr
Input Y,Pb,Pr signal from a DVD player.
 M  LAN (Optional)
This function is optional. 
P l e a s e   s e e   p a g e   3 4   N e t w o r k   C o n t r o l  
Application for details.
N  REAR IR RECEIVER
O  SPEAKER
P   Slot  for  Kensington  Micro  Saver Security System
Built-in Security Slot
This security slot supports the MicroSaver® 
Security System. MicroSaver® is a registered 
trademark of Kensington Microware Inc.  
The logo is trademarked and owned by 
Kensington Microware Inc.
ABC
DE
F
G
HI
J
K
L
M
N
P
O
(Please click here if your projector is with high efciency lter.) 
						

							Setting Up
9
Setting Up
Arrangement 
1.  Before installation, make sure that the projector is turned off and the power cord is disconnected. 
2.  Do not set up and move the projector, while it is hot. 
3.   The distance between the projector and screen determines the actual image size. Refer to the table 
below to determine the screen size at a given distance.
Note: The dimensions in the table below are approximate.
Screen size (diagonal) Distance (m) Distance (feet)
inch m Tele Wide Tele Wide40 1.0 0.95 0.77 3.13 2.53 
60 1.5 1.45 1.18 4.74 3.88 
70 1.8 1.69 1.39 5.55 4.56 
80 2.0 1.94 1.59 6.36 5.23
100 2.5 2.43 2.01 7.98 6.58 
150 3.8 3.67 3.03 12.03 9.95 
200 5.1 4.90 4.06 16.07 13.32 
250 6.4 6.13 5.09 20.12 16.69 
300 7.6 7.37 6.12 24.16 20.06
When in against at wall, leave about 20cm (7.9in.) Between thw projector and the wall.
6.12~7.37
4.06~4.9
3.03~3.67
2.01~2.43
1.59~1.94
1.18~1.45
0.77~0.95Distance(M)
Image size(inch)6.12~7.37
4.06~4.90
3.03~3.67
2.01~2.43
1.59~1.94
1.18~1.45
0.77~0.95
Image size(inch)
Distance(M) 
						

							10
Setting Up
Power ON / OFF
Turning on the power
1.  Make sure that power cord is rmly and correctly connected to the projector.
2.  Remove the lens cover, and the POWER  indicator will light up in green.
3.  Press POWER button on the control panel or  the remote control to turn on the projector.
4. Rotate the zoom ring to adjust the screen size. 
5. Rotate the focus ring to adjust the focus.
Turning off the power
1.  Press the POWER button on the control  panel or the remote control. The “power off”  
conrmation message appears.
2.  Press the POWER button again while the  message appears.
3.  When the projector enters “Standby” mode,  the POWER indicator will light up in green.
4.  If you don’t use the projector, remove power  cord.
 WARNING
  Do not touch around the lamp cover and the  
exhaust vents during use or just after use, since it  
is too hot.
POWER indicator
AC inlet Outlet
Focus ring Zoom ring
Power off?Please press
key again to power off.
 WARNING
   A strong light is emitted when the projector’s  
power is on. Do not look into the lens of the  
projector or look inside of the projector through 
any of the projector’s openings.
 CAUTION

  Do not turn off the AC power for 60 seconds  
after the lamp is turned on. Doing so could cause  
premature lamp failure.
(Please click here if your projector  
is with high efciency lter.)   
						

							11
Setting Up
Setting Up The Projector 
The projector supports the following four different projection methods. 
1.Front projection
2.Rear projection3.Rear ceiling projection 
4.Front ceiling projection
Special installation is required in order to suspend the projector from the ceiling. Please ask your  
dealer for details.  
						

							12
Setting Up
Ceiling Mounted Installation Guide 
Attach ceiling mount at four-suspension bracket xing points when suspending from a ceiling.  
Special installation is required in order to suspend the projector from the ceiling. Please ask your 
dealer for detals.
Security Anchor
The product is equipped with security 
anchor and PIN LOCK functions to help 
prevent unauthorized removal projector.
MAX M4x8 mm For Mounting.
WARNING
Do not grasp the security anchor to carry projector, since it is not designed for it. 
 The security anchor is not for comprehensive theft prevention measures. It is intended to be  used as supplemental theft prevention measure.
(Please click here if your projector  
is with high efciency lter.) 
						

							13
Setting Up
Adjusting The Projector’s Elevation
Use the adjustable foot at the front of the projector to set the image height.
1   Holding the projector, push the foot adjust buttons to loosen the front adjustable foot.
12   Position the front side of the projector to the desired height.
3   Release the foot adjust buttons in order to lock the front adjustable feet.
14   After making sure that the front adjustable feet are locked, put the projector gently  
atop.
 CAUTION
*  The adjustment range of front adjustable  foot is 0 to 8.5 degrees.
*  When the foot is adjusted, it may cause the  shape of the projected image to become  
distorted. Use the keystone correction 
function  to correct this distortion.
(Please click here if your projector  
is with high efciency lter.) 
						

							14
Setting Up
AUDIO OUTMOUSERS-232AUDIO OUTDVI OUTVGA OUTVGA OUTRGB IN
AUDIO IN 
VIDEO OUT AUDIO OUT (L)&(R)
S-VIDEO OUTY Pb/Cb Pr/Cr
How To Connect
Laptop or desktop computer
Before starting, make sure that the projector and computer are both turned off.
Connect the computer cable.
Connect either end of the computer cable to the projector’s RGB IN.  
Connect the computer cable from the computer to the projector.
If needed, connect the MONITOR OUT to a monitor to view input from RGB IN.
Tighten the screw on all connectors.
(Please click here if your projector is  
with high efciency lter.) 
						

							15
Setting Up
How To Connect 
Laptop or desktop computerConnect the audio cable if necessary
1.  If you connect end of the computer cable to the projector’s RGB IN. Please  connect one other end of the audio cable to the AUDIO IN 1.
2.  If you connect the DVI cable to the projector’s DVI-I IN. Please connect one  other end of the audio cable to the AUDIO IN 2.
3.  If you connect the S-Video/ Video/ Y,Pb,Pr port of the projector. Please connect  the other end of the audio cable to the AUDIO IN 3 jack on the computer
Connect USB Mouse
USB mouse compatible MS-Window98/ 2000/ NT/ XP/ Me, Macintosh : 
OS8.6~10.1, and a Microsoft Mouse driver installed. 
1. Insert the end of the USB Cable (B-Type) to the projector’s USB port.
2. Connect the end of the USB Cable (A-type) to the computer’s USB port.
3.  When the projector and computer are turned on, the appropriate drivers should load automatically.
  If the selected video image is not displayed after  the projector is turned on and 
the correct video source has been selected, please check that the video source  
device is turned on and operating correctly. Also check that the signal cables 
have been connected correctly. 
  Many laptops do not turn on their external video ports when connected  to a projector. Usually a key combination like Fn + F3 or CRT/LCD key  
turns the external display on / off. Locate a function key labeled CRT/LCD 
or a function key with a monitor symbol on the laptop. Press Fn and the 
labeledfunction key simultaneously. Refer to your laptop’s documentation to 
discover your laptop’s key combination.  
						

							Remote Control
16
Remote Control
Remote Control Battery Installation
1. Remove the battery cover. 
2.  Load the batteries. Make sure the plus pole is correctly oriented.
3. Close the battery cover.
 Caution
 Avoid excessive heat and humidity. 
Do not drop the remote control. 
 Do not expose the remote control to water or moisture, this could result in malfunction. 
 If the remote control will not be used for an extended period, remove the battery.
 Replace the battery when remote control operation becomes sluggish or unresponsive. 
 Do not place the remote control close to the cooling fan of the projector. 
 Do not use batteries of different types at the same time.
 Do not mix a new battery with used one. Make sure the plus and terminals are correctly  aligned when loading a battery.
 Dispose of batteries in accordance with environmental laws.
 Do not disassemble the remote control. If the remote control needs service, please contact  
						

							17
Remote Control
-        VOL        +
INPUT
ESC
MENU
AutoK
Still Blank
Power
Power on operation mode, standby mode, cool  
down mode.
ESC
Press “ ESC ” button to close “Menu” picture.
Volume +/-
Adjust Volume higher or lower.
Menu
Display or hide the On-Screen Display main 
menu page.
Keystone
Adjust the vertical keystone function.
Still
Keep the current image on the screen.