Boxlight Projectowrite User Manual

							
Interactive  Projector             
-44- 
5.Section five: Toolbar Options
Toolbar location
Push  t he  b utton  o f  “ wand/pen”   t o   relocate this   
on either the right-side or left -side of screen. 
Mouse
Pen
Eraser
Selectthe line thickness
Selectthecolorofpen
Eraseall
Savefiles
Recall
Virtualkeyboard
1/21/2008  
						

							
Multimedia LCD Projector             
-45- 
How to Connect 
Before starting, make sure that the projector and computer  are both  
turned off. 
1. Connect the computer cable. 
1.1   Connect either end of the vga cable to the computer
computer 1/ computer port. 
1.2Dsconnect the monitor cable   from the computer and connect the 
other end of the terminal where the monitor cable is disconnected 
from the computer. 
1.3If needed, connect the monitor cable of the computer monitor to 
the projector’s Computer out. 
1.4Tighten the screws on all connectors.
2.Connect the audio cable if necessary. 
2.1Connect one end of the audio cable to the Audio in jack on the 
projector. 
2.2Connect the other end of the audio cable to the audio output port on 
the computer sound card. 
1/21/2008  
						

							
-49- 

Turning off the projector
1.Press the power button on the projector or remote control. The power off 
confirmation message appears .If you do not want to power off the 
projector, ignore the message and it will disappear. 
       
      
2.Press the power button again and the projector will enter cool-down 
mode. The lamp shuts off, the lamp indicator flashes red, and the fans 
continue to run for approximately two minutes. During the cool down 
sequence the projector will not respond to any control panel or remote 
control buttons.  
Caution: Do not set the power switch to off or unplug the projector during the 
cool-down sequence. Not allowing the lamp to cool properly will greatly reduce the 
life of the lamp.
3.After the cool-down sequence is complete the fans will shut off and the 
lamp indicator will stop flashing. The projector is now in standby mode 
and can be turned back on with the remote control or control panel. If the 
projector will not be used for an extended period, set the power switch to 
off and disconnect the power cord. 
Interactive  Projector             
1/21/2008  
						

							
-46- 
Laptop PC 
Before beginning, make sure that the projector and computers are both turned 
off.
1. Connect the computer cable. 
1.1Connect either end of the computer cable to the projector’s 
computer 1 port. 
1.2Connect the other end of the project cable to the monitor out 
connection on the laptop. 
1.3Tighten the all connectors. 
2.Connect the audio cable if necessary.  
2.1Connect one end of the audio cable to the Audio in jack on the 
projector. 
2.2Connect the other end of the audio cable to the audio output port 
on the laptop PC. 
Interactive  Projector             
1/21/2008  
						

							
-47- 
Video
Connect to a video source 
The Projector can receive composite AV ,YPbPr and S-Video. 
1Connect RCA plug at projector and video source ( like DVD player) for 
video signal. 
2. Connect RCA plug ( white and red) to audio source ( like DVD player) 
and connect the phone jack to projector for audio signal. 
3. Connect YPbPr  plug at projector computer in 2 port and video source 
( like DVD player) for video signal. 
4For S-Video, using S-Video cable connect to projector and video source 
for video signal. 
Interactive  Projector             
1/21/2008  
						

							
-48- 

Adjust the Screen Image 
1. Adjusting the image size 
Turn the zoom ring on the projector to adjust the image size. 
2.Adjusting the image height. 
Extend or retract the front adjustable feet to adjust the height of the image. 
3.Correcting Keystone Distortion 
Use the [Keystone] button on the projectors control panel. 
*Correcting vertical keystone distortion 
Interactive  Projector             
1/21/2008  
						

							
           
-50- 
Functions of Menu (OSD) 
Keypad Operating: 
1.: Turn on and turn off the projector 
2.Blank:Blanks the projected image. If the projector is left in Blank 
mode for more than 15 minutes, the projector will automatically shut 
off the lamp and enter cool-down mode. 
3.Auto: Automatically adjusts the settings to match the current input. 
4.Source: Selects VIDEO or PC input source. 
5.Menu: Enter or exit the main menu (Show and hide the OSD) 
6.: Up / Down arrow buttons, used to navigate through the OSD 
Menus.
: Right / Left arrow buttons, used to select and adjust OSD Menu 
functions. 
7.Keystone: Adjusts the vertical keystone with the right and left arrow 
buttons. 
**There is a “Quick Key“ on the remote control and projector keypad as 
well.
**Press the “Volume” button on remote control, you can adjust value, and 
select between Brightness – Contrast – Keystones – Volume directly. 
 There is the same function for pressing the  button on the keypad 
Interactive Projector
1/21/2008  
						

							
            
-51- 
Computer mode
1. PICTURE 
Brightness 000/100 Adjusts the overall image brightness 
Contrast  000/100 Adjusts the difference between light and dark 
areas of the image 
sharpness 000/002 Adjusts the image sharpness 
Display mode  Select  
 Powerful 
Video
Presentation
Natural
Cinema
User
Enhance brightness 
Keep the soft tender color  
For computer presentation use 
Nature color 
Enhance contrast mode for Cinema mode 
adjustments of each RGB color 
 User Red 
User Green
User Blue 
000/100
000/100
000/100
Interactive Projector
1/21/2008  
						

							
-52- 
2. AUDIO 
Volume 000/040 Adjusts the volume 
Mute off/on Mutes the volume on/off 
Interactive  Projector             
1/21/2008  
						

							
-53- 
3.SETTING 
H position 000/100 Move the image position horizontally 
V position 000/100 Move the image position vertically 
Phase 000/100 Set the synchronization polarity 
Frequency 000/100 Set the horizontal scanning frequency 
Auto keystone execute Automatically Corrects keystone distortion in image i.e. 
press once to do once 
Keystone V -80/+80 Corrects vertical keystone distortion in image 
Auto sync execute Sets all of the above settings automatically 
Auto search off/on Search signal source automatically. 
Interactive  Projector             
1/21/2008