Brother Quattro 3 User Manual

NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
19
6162 6364
**In some countries or regions, this is  not included in the enclosed accessories.
No. Part Name Part Code
Americas Others
1 Zigzag foot “J” (on machine) XC3021-051
2 Monogramming foot “N” X53840-351
3 Overcasting foot “G” XC3098-051
4 Zipper foot “I” X59370-051
5 Buttonhole foot “A” X57789-251
6 Blind stitch foot “R” X56409-051
7 Button fitting foot “M” 130489-001
8 Walking foot SA140 F033N: 
XC2214-052
9 Side cutter foot SA177 F054: XC3879-152
10...

NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
20
Options
The following are available as optional accessories 
to be purchased separately from your authorized 
Brother dealer.
12 3
45 6
78 9
10 11 12
13 14 15
16
No. Part NamePart Code
Americas Others
1 Border embroidery frame H 30 cm × W 10 cm
(H 12 inches × W 4 inches) 
with Kit 3 upgrade SABF6000D2 NV1UGK3
2 Border embroidery frame set H 18 cm × W 10 cm
(H 7 inches × W 4 inches) SABF6000D BF2:
XE5059-001
3 10 spool stand SA560 TS4:
XE5065-101
4 Wide table...

NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
21
Using the Spool Stand
The included spool stand is useful when using 
thread spools with a large diameter (cross-wound 
thread). The spool stand can hold two spools of 
thread.
■How to assemble the spool stand
aFully extend the telescopic thread guide 
shaft, and then rotate the shaft until the two 
internal stoppers click into place.
bInsert the telescopic thread guide into the 
round hole at the center of the spool 
support, and then use a screwdriver to...

NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
22
cFirmly insert the two spool pins into the two 
holes in the spool support.
dOpen the upper cover of the machine. From 
the back of the machine, press in the upper 
cover latches (one on each side), and then 
pull the upper cover up to remove it from 
the machine.
eInsert the spool stand onto the notches of 
the machine.
■How to remove
aFrom the back of the machine, press in the 
spool stand latches (one on each side), and 
then pull the spool stand up to...

NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
23
Using the Pen Tablet
■Installing a battery in the tablet pen
A battery for the tablet pen is not included with your 
machine. Use a new AAA alkaline battery (LR03).
aUnscrew the upper barrel of the tablet pen.
bInstall a new AAA alkaline battery (LR03) in 
the tablet pen with the positive end (+) 
pointing up.
cScrew the upper barrel to the tablet pen.
■Replacing the pen tip
When the pen tip is worn out, replace with a new 
one included with your pen tablet....

NAMES OF MACHINE PARTS AND THEIR FUNCTIONS
24
bGently pull the pen tip straight out.
cPush in the new pen tip until it is flush with 
the tablet pen.
■Using with My Custom Design
aSelect a favorite picture for creating 
embroidery pattern.
bInsert the picture under the tablet sheet.
cActivate My Custom Design, then trace the 
picture with the tablet pen.
For detailed instructions about operating My 
Custom Design, refer to the Operation Manual 
(PDF format) stored on the My Custom Design CD.
Note
 When...

Chapter 1
Getting Ready
TURNING THE MACHINE ON/OFF ...............26
LCD SCREEN...................................................28
■Home Page Screen ................................................................... 28
■ Utility Stitch LCD Screen ......................................................... 29
■ Key Functions ........................................................................... 30
USB Connectivity.............................................................. 32
■Using USB Media or...

TURNING THE MACHINE ON/OFF
26
TURNING THE MACHINE ON/OFF
 WARNING
 Use only regular household electricity for the power source. Using other power sources may result in fire, electric shock, or damage to the machine.
 Make sure that the plugs on the power cord are firmly inserted into the electrical outlet and the power  cord receptacle on the machine.
 Do not insert the plug on the power cord into an electrical outlet that is in poor condition.
 Turn the main power to OFF and remove the plug in the...

TURNING THE MACHINE ON/OFF
Getting Ready
27
1
aInsert the power supply cord into the power 
cord receptacle, then insert the plug into a 
wall outlet.
aMain power switch
b Power supply cord
bTurn the main power switch to “I” to turn 
on the machine.
aOFF
b ON
cTurn the main power switch to “O” to turn 
off the machine. 
Memo
 When the machine is turned on, the needle 
and the feed dogs will make sound when 
they move; this is not a malfunction. 

LCD SCREEN
28
LCD SCREEN
When the machine is turned on, the opening movie is played. Touch anywhere on the screen for the 
home page screen to be displayed. Touch the LCD screen or a key with your finger or the included touch 
pen to select a machine function.
■Home Page Screen
Note
 When the straight stitch needle plate is on the machine, the needle will automatically move to the mid-
dle position.
Memo
 Only touch the screen with your finger or the included touch pen. Do not use a sharp pencil,...