Candy Cdcf 6 Service Manual

5Proper Use of Detergent
WARNING! YOU  MAY NOT ADD TOO MUCH DETERGENT TO PREVENT THE FORMATION OF DEPOSITS BECAUSE YOUR DISHWASHERS 
HAVE  SPECIALLY-DESIGNED WATER SOFTENERS.
The dispenser must be refilled before the start of each wash cycle following the instructions provided in the Wash Cycle 
Table.Your dishwashers use less detergent and rinse aid than conventional dishwashers. Generally, only one tablespoon
 of detergent is needed for a normal wash load. Also, more heavily soiled items need more...

6
Loading the Dishwasher Racks.
For best performance of the dishwasher, follow these loading guidelines. Features and appearance of racks and 
silverware baskets may vary from your model.
IN
66
99
33
11
11
8877
22
44
33
3333551010
It is preferable to place serving dishes and lids on the side of  the racks in order to avoid blocking the rotation of the top spray arm.
Pots, serving bowls, etc, must always be placed top down.                 Deep pots should be slanted to allow water to flow out....

7
SILVERWARE BASKET
Silverware should be placed in the silverware basket with handles at the bottom: If the rack has side baskets, the spoon should be loaded individually into the appropriate slots, Especially long utensils should be placed in the horizontal position at the front of the upper rack.
Turning on the Appliance
When the washing cycle has finished, an 8 second buzzer will sound.Turn off the appliance using the ON/OFF button,open the door of the dishwasher. Wait a few minutes before unloading...

8Caring for the Dishwasher
To clean the control panel use a lightly dampened cloth then dry thoroug\
hly.  To clean the dishwasher outside, do
 not use solvents (degreasing action) neither abrasives, but only a cl\
oth soaked  with water.
 Never use sharp objects, scouring pads or harsh cleaners on any part  of the dishwasher.
Protect Against Freezing
If your dishwasher is left in an unheated place during the winter, ask a\
 service technician to:Cut off electrical power to the dishwasher. Remove
fuses...

9WARNING!  

10About Electricity Connecting
.
Insure proper ground 
exists before use
CAUTION , for personal safety:
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD GROUNDING PRONG FROM THE POWER CORD.
Electrical Requirements  
This dishwasher is designed for operation on an adequately wired individual 220~240VAC,50~60HZ. Use required fuse 10 amp. 
Fused electrical supply is required-copper wire only. Time delay fuse or circuit breaker...

11How to Drain Excess Water 
From Unicouple Hoses
If the sink is 34 or higher from the floor, the excesswater in Unicouple\
 hoses
cannot be drained directly into the sink. It will be necessary to drain \
excess
water from hoses into a bowl or suitable container that is heldoutside a\
nd lower
 than the sink.
Positioning the Appliance Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent 
cabinets or wall. The dishwasher is...

12Problem
Possible Causes What To Do
Fuse blown, or the
circuit breaker acted Replace fuse or reset circuit breaker. Remove any other 
appliances sharing the same circuit with the dishwasher
NoiseSound from soft food shredding action and detergent cup
opening.
Utensils are not secure
in the baskets or something
small has dropped into
the basket To ensure everything is secured in the dishwasher.
Motor hums Dishwasher has not been used regularly. If you do not use it 
often, remember to set it to fill and...

13Before  calling  for  service . . .
Problem
Possible Causes What To Do
Cloudiness on
 glasswareCombination of soft
water and too much
detergent Use less detergent if you have soft water and select a 
shortest cycle to wash the glassware and to get them clean. 
Yellow o r b rown f ilm
on inside surfacesTea or coffee stains using a solution of 1/2 cup of bleach and 3 cups warm water
to remove the stains by hand. 
WARNING
You have to wait for 20 minutes after a cycle to let the heating
elements cool down...