Canon Camera Eos 1d X User Manual

							101
3 Customizing AF Functions
The AF points and grid  in the viewfinder can be illumina ted in red when focus is achieved.
AUTO: Auto
The AF points and grid are automatically 
illuminated in red under low light.
ON: Enable
The AF points and grid are illuminated in 
red regardless of the ambient light level.
OFF: Disable
The AF points and grid are not 
illuminated in red.
The AF status indicator indicating th at AF is operating can be displayed 
in the viewfinder’s field of view  or outside the field of view.
: Show in field of view
The AF status icon  is displayed in the 
lower right of the viewfinder’s field of view.
: Show outside view
The < e> icon is displayed below the 
focus confirmation light < o> outside the 
viewfinder’s field of view.
You can make fine adjustments for the  AF’s point of focus. For details, 
see “Fine Adjustment of AF’s Po int of Focus” on the next page.
VF display illumination
AF status in viewfinder
The setting here is not applied to the electronic level display (p.61) in the viewfinder.
The AF points and grid will always  be illuminated in red when you press 
 for AF point selection.
AF Microadjustment
The AF status indicator will  also be displayed when you  hold down the shutter button 
halfway after focus is achieved or when you ho ld down the  button.
COPY  
						

							102
Fine adjustment of the AF’s point of focus is possible for viewfinder 
shooting and in Live View shooting’s [ Quick mode]. This is called “AF 
Microadjustment”. Before making the adjustment, read “Notes for AF\
 
Microadjustment” on page 107.
Normally, this adjustment is not required. Do this adjustment 
only if necessary. Note that performing AF Microadjustment 
may prevent correct focusing from being achieved.
Set the adjustment value manually by  adjusting, shooting, and checking 
the result. Repeat this until the desir ed adjustment is made. During AF, 
regardless of the lens used, the poin t of focus will always be shifted by 
the adjustment amount.
1Select [AF Microadjustment].
  Under the [ 25] tab, select [ AF 
Microadjustment], then press < 0>.
2Select [All by same amount].
  Turn the < 5> dial to select [ All by 
same amount ].
3Press the  button.
XThe [ All by same amount ] screen 
will appear.
3 Fine Adjustment of AF’s Point of Focus
Adjust All by Same Amount
COPY  
						

							103
3 Fine Adjustment of AF’s Point of Focus
4Make the adjustment.
 Turn the < 5> dial to make the 
adjustment. The adjustable range is 
±20 steps.
  Setting it toward “–: ” will shift the 
point of focus in front of the standard 
point of focus.
  Setting it toward “+: ” will shift the 
point of focus to the rear of the 
standard point of focus.
  After making the adjustment, press 
.
  Turn the < 5> dial to select [ All by 
same amount ], then press . 
The menu will reappear.
5Check the result of the 
adjustment.
  Take a picture and play back the 
image (p.246) to check the 
adjustment result.
  When the resulting picture is focused 
in front of the targeted point, adjust 
toward the “+: ” side. When the 
resulting picture is focused behind the 
targeted point, adjust toward the “–
: ” side.
  If necessary, repeat the adjustment.
If [All by same amount ] is selected, AF adjustment  will not be possible for 
the wide-angle and telephot o ends of zoom lenses.
COPY  
						

							3 Fine Adjustment of AF’s Point of Focus
104
You can perform AF Microadjustmen t for each lens and register the 
adjustment in the camera. You can r egister the adjustment for up to 40 
lenses. When you autofocus with  a lens whose adjustment has been 
registered, the point of focus will always be shifted by the adjustment 
amount
.Set the adjustment manually by adjus ting, shooting, and checking the 
result. Repeat this until  the desired adjustment is  made. If you use a zoom 
lens, make the adjustment for the wi de-angle (W) and telephoto (T) ends.
1Select [Adjust by lens].
 Turn the < 5> dial to select [ Adjust 
by lens ].
2Press the < B> button.
XThe [ Adjust by lens ] screen will 
appear.
3Check and change the lens 
information.
Check the lens information.
  Press the < B> button.
X
The screen will show th e lens name and a 10-
digit serial number. When  the serial number is 
displayed, select [
OK] and go to step 4. If the lens’ serial number cannot be 
confirmed, “0000000000” will be displayed. 
Enter the number as indicated below. See 
the next page about the asterisk “ * ” 
displayed in front of  the lens serial number.
Adjust by Lens
COPY  
						

							105
3 Fine Adjustment of AF’s Point of Focus
Enter the serial number.
 Turn the < 5> dial to select the digit, 
then press < 0> to display < r>.
  Turn the < 5> dial to enter the 
number, then press < 0>.
  After entering all the digits, turn the 
 dial to select [ OK], then press 
< 0 >.
About the Lens Serial Number
  In step 3, if “ * ” appears in fr ont of the 10-digit lens serial 
number, you cannot register several copies of the same lens 
model. Even if you enter the serial number, “ * ” will remain 
displayed.
  The lens serial number on the lens  may differ from the serial 
number displayed on the screen in  step 3. This is not a defect.
  If the lens serial number includes  letters, enter only the numbers in 
step 3.
  The location of the serial number differs depending on the lens.
  Some lenses may not have a serial number inscribed. To register a 
lens that has no serial number in scribed, enter any serial number in 
step 3.
  If [Adjust by lens ] is selected and an Extender is used, the adjustment 
will be registered for the le ns and Extender combination.
  If 40 lenses have already been re gistered, a message will appear. After 
you select a lens whose registration  is to be erased (overwritten), you 
can register another lens.
COPY  
						

							3 Fine Adjustment of AF’s Point of Focus
106
4Make the adjustment.
 For a zoom lens, turn the  dial and 
select the wide-angle (W) or telephoto 
(T) end. Press  to turn off the 
purple frame and make the adjustment.
  Turn the < 5> dial to adjust as 
desired, then press . The 
adjustable range is ±20 steps.
  Adjusting toward “–: ” will shift the 
point of focus in front of the standard 
point of focus.
  Adjusting toward “+: ” will shift the 
point of focus to the rear of the 
standard point of focus.
  For a zoom lens, repeat step 4 and 
adjust it for the wide-angle (W) and 
telephoto (T) ends.
  After completing the adjustment, 
press the < M> button to return to 
the screen in step 1.
 
Turn the  dial to select [Adjust by lens], 
then press <
0>. The menu will reappear.
5Check the result of the adjustment.
 Take a picture and play back the image 
(p.246) to check the adjustment result.
 When the resulting picture  is focused in front of 
the targeted point, adjust toward the “+: ” side. 
When the resulting pictur e is focused behind the 
targeted point, adjust  toward the “– : ” side.
 If necessary, repeat the adjustment.
Single focal length lens
Zoom lens
When shooting with the intermediate range (f ocal length) of a zoom lens, the AF’s 
point of focus is corrected relative to the adjustments made  for the wide-angle and 
telephoto ends. Even if onl y the wide-angle or telephoto end has been adjusted, a 
correction will be made automatica lly for the intermediate range.
COPY  
						

							107
3 Fine Adjustment of AF’s Point of Focus
When [  Clear all ] appears at the bottom of the screen, pressing the 
< L > button will clear all the  adjustment data set for [All by same 
amount ] and [Adjust by lens ].
Notes for AF Microadjustment
Clearing All AF Microadjustment data
 The AF’s point of focus will vary  slightly depending on the subject 
conditions, brightness, zoom positi on, and other shooting conditions. 
Therefore, even if you perform AF Microadjustment, focus may still not 
be achieved at th e suitable position.
  The adjustment data will be retained  even if you clear all the camera 
settings (p.58). However, the setting itself will be [ Disable].
 It is best to make the adjustment at  the actual location where you will 
shoot. This will make th e adjustment more precise.
  Using a tripod when making the adjustment is recommended.
  To check the result of the adjustment, setting the  image size to JPEG L 
(Large) and the JPEG quality (com pression) to 8 or higher is 
recommended.
  The adjustment amount of one step  varies depending on the maximum 
aperture of the lens. Ke ep adjusting, shooting, and checking the focus 
repeatedly to adjust th e AF’s point of focus.
  AF adjustment is not possible  for Live View shooting’s [Live mode] and 
[ u  Live mode ] (contrast AF).
COPY  
						

							108
Autofocus can fail to achieve focus (the viewfinder’s focus confirmation 
light < o> blinks) with certain subjects such as the following:
Subjects difficult to focus
  Very low-contrast subjects
(Example: Blue sky, solid-color walls, etc.)
  Subjects in very low light
  Extremely backlit or reflective subjects
(Example: Car with a highly reflective body, etc.)
  Near and far subjects covered by an AF point 
(Example: Animal in a cage, etc.)
  Repetitive patterns
(Example: Skyscraper windows,  computer keyboards, etc.)
In such cases, do either of the following:
(1) With One-Shot AF, focus on an obj ect at the same distance as the 
subject and lock the focus before recomposing (p.67).
(2) Set the lens focu s mode switch to  and focus manually (p.109).
When Autofocus Fails
For conditions where AF can fa il to achieve focus with [Live mode]/[u Live 
mode ] during Live View sh ooting, see page 213.
COPY  
						

							109
When Autofocus Fails
1Set the lens focus mode switch to 
.
2Focus the subject.
 Focus by turning the lens focusing 
ring until the subject looks sharp in 
the viewfinder.
MF: Manual Focusing
Focusing ring
 If you press the shutter  button halfway while focu sing manually, the focus 
confirmation light < o> will light up when  focus is achieved.
  With 61-point automa tic selection, when the center AF point achieves 
focus, the focus confirmation light < o> will light up.
COPY  
						

							110
Single and continuous shooting drive modes are provided.
1Press the  button. (9 )
2Select the drive mode.
 While looking at the top LCD panel, 
turn the < 5> dial.
u : Single shooting
When you press the shutter button  completely, only one shot will 
be taken.
o : High-speed continuous shooting  (Max. approx. 12 shots/sec.)
p : Low-speed continuous shooting  (Max. approx. 3 shots/sec.)
While you hold down the shutter bu tton completely, shots will be 
taken continuously.
k : 10-sec. self-timer
l : 2-sec. self-timer
See page 112 for the self-timer procedure.
R : Selecting the Drive Mode
When < o> is set, the maximum contin uous shooting speed will 
be approx. 10 shots/sec. if the  ISO speed is set to any of the 
following:
• ISO 32000 or higher is set manually.
• [Auto ISO range ]’s [Maximum] is set to [ 51200] and Auto ISO 
automatically sets ISO 32000 or higher.
• [8 1: Safety shift ] is set to [ISO speed ] and the safety shift 
automatically sets ISO 32000 or higher.
Note that if the camera’s internal  temperature is low, and when ISO 
20000 or higher is se t manually or automati cally, the maximum 
continuous shooti ng speed for  will be approx. 10 fps.
COPY