Canon cinema EOS1D C User Manual

21
2
Transferring Images
to an FTP Server
With FTP transfer, you can automatically transfer each 
image to the FTP server as you shoot or transfer 
images in batches after shooting. 

22
These instructions are continued from Chapter 1.
1 Turn the  dial to select [Address 
setting], and then press .
2 If you set the DNS server setting to 
[Disable], the screen on the left is 
displayed.
 Press  to select the input 
position, and then turn the  dial 
to enter the IP address of the FTP 
server.
 If you set the DNS server IP address 
setting to [Auto assign] or [Manual 
setting], the screen on the left is 
displayed.
 For instructions on screen operations, 
see “Virtual Keyboard...

23
Configuring FTP Communication Settings
4    Complete the [Passive mode] 
settings.
 If an Error 41 (“Cannot connect to 
FTP server”) is displayed in step 8, 
setting [Passive mode] to [Enable] 
may resolve it.
5 Complete the [Proxy server] 
settings.
 Turn the  dial to select [OK], and 
then press  to go to the next 
screen.
6 Complete the [Login method] 
settings.
 Turn the  dial to select [OK], and 
then press  to go to the next 
screen.
7 Complete the [Target folder] 
settings.
 Select [Root...

Configuring FTP Communication Settings
24
8 On the confirmation screen displayed 
next, select [OK] and press .
XThe  lamp on the camera 
lights up green.
9 Press  and turn the  dial to 
select the set number, and then press 
.
 Turn the  dial to select [OK], and 
then press . After the 
connection wizard closes, the display 
will return to the menu screen.
The network settings for FTP transfer are now complete.
During image transfer, the  lamp on the camera blinks green. 

25
An image can be automatically transferred to the FTP server 
immediately after shooting. You can continue still photo shooting even 
while images are being transferred.
Before shooting, be sure to insert a memory card in the camera. If you 
shoot without recording images, they will not be transferred.
Note that automatic transfer of movies is not supported. Transfer 
movies after shooting, as described on pages 30-38. 
1Select [Communication settings].
2Select [Network settings].
 Once [Communication...

Automatic Image Transfer After Each Shot
26
4Select [Automatic transfer].
 Select [Enable].
5Take the picture.
XThe captured images are transferred 
to the FTP server.
Approx. number of shots
* Using a fully charged LP-E4N Battery Pack.
*[LAN power save: Enable]
* Based on Camera & Imaging Products Association (CIPA) standards.
Number of Possible Shots
Normal Temperature 
(23°C / 73°F)Low Temperature 
(0°C / 32°F) 
950740
 During continuous shooting, images are transferred to the FTP server in 
the order...

27
Automatic Image Transfer After Each Shot
With automatic transfer, you can select which images to transfer when 
recording images of different sizes to separate cards, or when recording 
both RAW and JPEG images.
1Select [Communication settings].
2Select [Network settings].
 Once [Communication func] is set 
to [Enable], you can select [Network 
settings].
3Select [Set up].
4Select [Transfer type/size].
Setting the Size or Type of Images to Transfer 

Automatic Image Transfer After Each Shot
28
5Select the size and type of images 
to transfer.
 To transfer smaller JPEGs when the camera is set up to record 
larger JPEGs to one card and smaller JPEGs to the other, set [JPEG 
size to trans.] to [Smaller JPEG].
 To transfer either RAW or JPEG images when the camera is set up 
to record RAW images to one card and JPEGs to the other, specify 
which images to transfer in the [RAW+JPEG transfer] setting. 
Similarly, complete the same setting when RAW+JPEG...

29
Automatic Image Transfer After Each Shot
 In the menu, select [Communication settings]  [Network 
settings]  [Set up]  [LAN power save].
 When this option is set to [Enable], the camera will log off from the 
FTP server after transfer and switch to standby mode. Wired 
connectivity will be restored automatically when you attempt to 
transfer images, and the camera will reconnect to the FTP server.
Enabling LAN Power Management 

30
Simply select an image and press  to transfer it. You can add a 
caption before transferring the image. You can continue still photo 
shooting even while images are being transferred.
1Select [Communication settings].
2Select [Network settings].
 Once [Communication func] is set 
to [Enable], you can select [Network 
settings].
3Select [Set up].
Transferring Images Individually
Transferring the Current Image