Canon Lv-7265, Lv-7260, Lv-x7 Multimedia Projector Users Manual

							42
5. Using On-Screen Menu
❸
 List of Menu Items
Image adjustment   Default  Item     
Image mode      1: Standard, 2: Presentation, 3: Cinema, 4: Video, 5: sRGB
 Detail settings General
      Reference    Standard, Presentation, Cinema, Video, sRGB
      Gamma    Dynamic, Natural, Black detail
      Color temperature    XLow, Low, Mid, High
   White balance
    
Brightness RGB, Contrast RGBBrightness
Contrast
Sharpness
Color level
Color balance
Reset
Display settings   Default Item    
Aspect    *  Normal, Wide zoom, Cinema, True size
Cinema position
Horizontal position    *
Vertical position    *
Clock   *
Tracking   *
Video fi lter    Off  Off, Less, More
Setup    Default Item    
General 
Auto keystone (LV-7265 only) On  Off, On
   Keystone adjustment   
    Keystone save  Off  Off, On
    Screen color  Off  Off, Greenboard, Greenboard(Gray), Light yellow,
        Light green, Light blue, Sky blue, Light rose, Pink
   Lamp mode  Normal Normal, Quiet
    Language  English  English, Deutsch, Français, Italiano, Español,
        Português, Nederlands, Svenska, Norsk, Suomi,
      
Čeština, Magyar, Polski, Türkçe, Pyccкий, 
      
Eληνικά, 
ÔŠ , 
ÏÓ, 
à´	¯, 
, Dansk
Beep On Off, On
Installation  Image fl ip H/V  None  None / Rear, Ceiling mounted / Rear /
       Ceiling mounted
    Communication speed  19200bps  4800bps, 9600bps, 19200bps
    Key lock  Off  Off, On
   Password  Off  Off, On
    Menu color select  Color  Color, Monochrome
    Menu display time  45 sec  Manual, 5 sec, 15sec, 45 sec
    No signal screen  Blue  Blue, Black, Canon logo
Options  Off timer  Off  Off, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00
    Auto PC adjustment  Normal  Off, Normal, Fine
    Direct power on  Off  Off, On
    Power management  Off  Off, 0:05, 0:10, 0:20, 0:30
   Fan mode  Auto  Auto, High
  
Default source select  LV-7265 Last Last, Auto, Computer 1, Computer 2 (Digital), Computer 2 (Analog), VIDEO, S-VIDEO
   LV-7260/LV-X7  Last  Last, Auto, Computer, VIDEO, S-VIDEO
   Deinterlace  On  Off, On
Input signal select  Computer 1 (LV-7265) 
RGB/COMPONENT  RGB/COMPONENT, RGB, COMPONENT
  Computer 2 (Analog) (LV-7265) RGB/COMPONENT  RGB/COMPONENT, RGB, COMPONENT
  Computer (LV-7260/LV-X7) RGB/COMPONENT  RGB/COMPONENT, RGB, COMPONENT
    VIDEO  Auto  Auto, NTSC3.58, NTSC4.43, PAL, PAL-M,
        PAL-N, PAL60, SECAM
    S-VIDEO  Auto  Auto, NTSC3.58, NTSC4.43, PAL, PAL-M,
    PAL-N, PAL60, SECAM
Some menu items are not available depending on the input source.
*  The asterisk (*) indicates that the default setting varies depending on the signal. 
						

							43
5. Using On-Screen Menu
Information   Item
Usage time  Remaining lamp time
   Lamp counter 
   Filter counter   
Input signal  Source index
   Horizontal frequency   
   Vertical frequency   
    Input signal type  RGB, Component, HDTV, VIDEO, S-VIDEO, HDTV, Digital
    Video type  NTSC, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM,
    Sync type  Separate Sync, Composite Sync, Sync on Green, Sync on video
   Sync polarity
    Scan type  Interlace, Progressive
Version Model
   Serial number
   Firmware version
   Data version
Reset   Item
Current signal     
All data     
Lamp counter
Filter counter 
						

							44
5. Using On-Screen Menu
❹
 Menu Descriptions & Functions [Image adjustment]
[Image mode]
    
When selecting user adjustable [Image mode], the submenu will be displayed.
You can customize each gamma or color. To do so, fi rst select [Image mode] and press the OK button, then pro-
ceed using the following steps.
[Detail settings]
   
Selecting Reference Setting [Reference]
This option allows you to adjust neutral tint for yellow, cyan or magenta. There are fi ve factory presets optimized 
for various types of images, you can set user adjustable settings.
Standard................ Select this to project an image with a similar quality to that of the original image. An image is projected 
with a high regard for reproduction of white.
Presentation .......... Select this to project an image with a similar qualit y to that of the original image. A bright and high-
contrast image is projected.
Cinema .................. Select this to project a moving picture. A picture is projected with a high regard for color tone repro-
duction.
Video ..................... Select this to project a regular picture such as T V program
sRGB ..................... Select this when you want to project an image from a sRGBcompatible digital camera. An image is pro-
jected in the display mode conforming to the sRGB Standard.
Selecting Gamma Correction Mode [Gamma]
Each mode is recommended for:
Dynamic ................ Creates a high-contrast picture.
Natural ................... Natural reproduction of the picture.
Black detail ............ Emphasizes detail in dark areas of the picture.
Adjusting Color Temperature [Color temperature]
This option allows you to select the color temperature of your choice:
XLow, Low, Mid and High.
NOTE: When [Standard] or [Presentation] is selected in [Reference], [Color temperature] is not available. 
						

							45
5. Using On-Screen Menu
Normal
Standard
4:3 Aspect
When 16:9 is selected from 
the source (i.e. DVD player), 
the following selections will 
display:
Normal
16:9 image displayed 
in 4:3 modeWide zoom Cinema True size
Left and right 
stretchedLeft and right 
stretched
Wide zoom Cinema
Left and right 
stretchedLeft and right stretched to 
display the true aspect
When 4:3 is selected from 
the source (i.e. DVD play-
er), the following selections 
will display:
Adjusting White Balance [White balance]
This allows you to adjust the white balance. Brightness for each color (RGB) is used to adjust the black level of the 
screen; Contrast for each color (RGB) to adjust the white level of the screen.
Adjusting Brightness, Contrast, Sharpness, Color level and Color balance
You can adjust brightness, contrast, sharpness, color level and color balance.
Brightness ............. Adjusts the brightness level or the black level of the image.
Contrast ................. Adjusts the intensity of the image according to the incoming signal (White level of the image).
Sharpness .............. Controls the detail of the image for Video (not valid for RGB).
Color level .............. Increases or decreases the color saturation level (not valid for RGB).
Color balance ........ Varies the color level from +/- green to +/-blue. The red level is used as reference. This adjustment is 
only valid for Video and Component inputs (not valid for RGB).
Reset
The settings and adjustments for [Image adjustment] will be returned to the factory settings with the exception of 
the following; numbers and [Reference] within the [Image mode] screen.
The settings and adjustments under [Detail settings] within the [Image mode] screen that are not currently select-
ed will not be reset.
❺
 Menu Descriptions & Functions [Display settings]
Selecting Aspect Ratio [Aspect]
Aspect allows you to select the best Aspect mode to display your source image.
You can also display the Aspect menu by pressing the ASPECT button on the remote control.
True size (RGB only): Turns off the scaling feature. The projector displays the current image in its true resolution. 
						

							46
5. Using On-Screen Menu
NOTE: 
•  When you are displaying an RGB image with a higher resolution than the projectors native resolution, the image will be dis-
played in the projector’s native resolution. In this case [True size] is not available from the menu.
  Only when displaying an RGB image with a lower resolution than the projectors native resolution, will the image be able to be 
displayed in its true resolution [True size].
  When Computer 2 (Digital) is selected, some options of Aspect Ratio are not available depending on the signal.
•  You can adjust the image position for Cinema aspect. See [Cinema position] for setting the image position.
Copyright
Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue such as 
a coffee shop or hotel and employing compression or expansion of the screen image with a [Aspect] setting may raise concern 
about the infringement of copyrights which are protected by copyright law.
Adjusting the Vertical Position of Image [Cinema position] (for Cinema in Aspect only)
This feature adjusts the vertical position of the image when viewing video with Cinema aspect ratio selected.
When [Cinema] is selected in [Aspect], the image is displayed with black borders on the top and bottom.
You can adjust the vertical position from the top to the bottom of the black area.
NOTE: This option is available only when [Cinema] is selected in [Aspect].
Adjusting Horizontal/Vertical Position, Clock and Tracking (available for RGB signal only)
You can adjust the image manually for position and stability; [Horizontal position], [Vertical position], [Clock] and 
[Tracking].
[Horizontal/Vertical position]
Adjusts the image location horizontally and vertically.
[Clock]
Use this item to fi ne tune the computer image or to remove any vertical banding that might appear. This function 
adjusts the clock frequencies that eliminate the horizontal banding in the image. This adjustment may be neces-
sary when you connect your computer for the fi rst time. 
[Tracking] 
Use this item to adjust the clock phase or to reduce video noise, dot interference or cross talk. (This is evident 
when part of your image appears to be shimmering.)
Use [Tracking] only after the [Clock] is complete.
NOTE: A projected image may not be displayed correctly during adjustment of [Clock] or [Tracking]. This is normal. 
NOTE: The [Horizontal position] and [Vertical position] options can be adjusted for component signals.
Selecting Video Filter Level [Video  lter] (not available for Digital RGB, Video and S -Video)
Select one of the three levels for reducing video noise: Off, Less or More.
Off ......................... The low-pass  lter is turned off.
Less ....................... The low-pass  lter is applied par tially.
More ...................... The low-pass  lter is applied fully.
NOTE: Selecting [Off] will give best image quality by way of higher bandwidth. Selecting [Less] will soften the image and select-
ing. 
						

							47
5. Using On-Screen Menu
❻
 Menu Descriptions & Functions [Setup]
[General]
   
Enabling Auto Keystone [Auto keystone] (LV-7265 only)
This feature allows the projector to detect its tilt and correct vertical distortion automatically.
To turn off the Auto Keystone feature, select [Off].
Correcting Vertical Keystone Distortion Manually [Keystone adjustment]
You can correct vertical distortion manually.
Saving Vertical Keystone Correction [Keystone save]
This option enables you to save your current keystone settings.
Off .......................... Does not save current keystone correction settings
On .......................... Saves current keystone correction settings
Saving your change once affects all sources. The changes are saved when the projector is off.
NOTE: When [Auto keystone] is set to [On], [Keystone save] is not available. Next time you turn on the power, the Auto keystone 
function will work and the data stored with [Keystone save] will be invalid.
Selecting Wall Color Correction Mode [Screen color]
This function allows for quick adaptive color correction in applications where the screen material is not white.
The following nine options are available: Off, Greenboard, Greenboard (Gray), Light yellow, Light green, Light blue, 
Sky blue, Light rose and Pink.
LV-7 2 6 5LV-7 2 6 0 / LV-X 7 
						

							48
LAMP
LAMP
5. Using On-Screen Menu
Selecting Lamp Mode [Lamp mode]
This feature enables you to select two brightness modes of the lamp: Normal and Quiet modes. The lamp life can 
be extended by using the Quiet mode.
Lamp Mode
Normal Mode
Quiet ModeDescription
This is the default set ting (10 0% 
Brightness).
Select this mode to increase the 
lamp life (approx. 80% Brightness).
Status of LAMP indicator
Off
Steady Green light
NOTE: 
•   The lamp life remaining and lamp hours used can be checked in [Usage time]. Select [Information] 
→[Usage time].
•   If the projector is overheated in Normal mode, there may be a case where the Lamp mode automatically changes to Quiet 
mode to protect the projector. This is called “forced cooling operation”. When the projector is in a forced cooling operation, 
the picture brightness decreases. When the projector comes back to normal temperature, the Lamp mode returns to Normal 
mode.
 Thermometer symbol [ 
 ] indicates the lamp mode is automatically set to a forced cooling operation because the internal 
temperature is too high. In this condition, changing [Lamp mode] setting in the menu will not affect the actual lamp mode 
and the LAMP indicator lights green.
Selecting Menu Language [Language]
You can choose one of 21 languages for the on-screen menu.
Enabling Key Sound and Error Sound [Beep]
This feature turns on or off the keypad sound or alarm when a button on the cabinet and the remote control is 
pressed or an error occurs. 
						

							49
5. Using On-Screen Menu
[Installation]
Selecting Projector Orientation [Image fl ip H/V]
This sets your image for your type of projection application. The options are:
front projection, rear projection, ceiling mounted projection and rear ceiling mounted projection.
Selecting Communication Speed [Communication speed]
This feature sets the baud rate of the SERVICE PORT (Mini DIN 8 Pin). It supports data rates from 4800 to 19200 
bps.
The default is 19200 bps.
Select the appropriate baud rate for your equipment to be connected (depending on the equipment, a lower baud 
rate may be recommended for long cable runs).
Your selected communication speed will not be affected even when [Reset] is done from the menu.
Disabling the Cabinet Buttons [Key lock]
This option turns on or off the Key Lock function for cabinet buttons.
NOTE:
•  The Key lock setting will not affect the remote control or PC control functions.
•  When the cabinet buttons are disabled, pressing and holding the BACK button on the projector cabinet for about 10 seconds 
will change the setting to enable.
•  The Key lock icon will be displayed at the top right of the menu when Key lock is enabled.
None
Rear, Ceiling mounted
Rear
Ceiling mounted 
						

							50
5. Using On-Screen Menu
Enabling Password [Password]
This feature turns on or off the Password function.
Unless the correct password is entered, the projector cannot project an image. (
→page 
36)
Selecting Menu Color [Menu color select]
You can choose between two color modes for menu color: color and monochrome.
Selecting Menu Display Time [Menu display time]
This option allows you to select how long the projector waits after the last touch of a button to turn off the menu.
The preset choices are [Manual], [5 sec], [15 sec], and [45 sec].
Selecting a Color for Background [No signal screen]
Use this feature to display a blue, black screen or the Canon logo screen when no signal is available.
[Options]
Setting Off Timer [Off timer]
You can use the Off Timer feature to turn off the projector automatically at a preset time.
Eight preset times can be selected:Off, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00 and 16:00.
Setting Auto Adjust [Auto PC adjustment]
Selecting [Normal] or [Fine] will automatically execute Auto PC adjustment function at the time of signal switching.
This feature sets the Auto PC adjust mode so that the analog RGB image can be automatically or manually adjust-
ed for noise and stability. You can automatically make adjustment in two ways: Normal and Fine
Off .......................... The RGB image will not be automatically adjusted.
You can manually optimize the RGB image.
Normal ................... Default setting. The RGB image will be automatically adjusted. Normally select this option.
Fine ........................ Select this option if  ne adjustment is needed. It takes more time to switch to the source than when [Nor-
mal] is selected.
Enabling Direct Power ON [Direct power on]
Turns the projector on automatically when the power cord is inserted into an active power outlet. This eliminates 
the need to always use the POWER button on the remote control or projector cabinet.
To use the [Direct power on] function, you must fi rst press the main power switch to the position “On” (I) before 
plugging the power cord.
Enabling Power Management [Power management]
When this option is selected you can enable the projector to automatically turn off (at the selected time: 5 min., 10 
min., 20 min., 30 min.) if there is no operation with no signal received by any input. 
						

							51
5. Using On-Screen Menu
Enabling Fan Speed Mode [Fan mode]
This option allows you to select two modes for fan speed: Auto mode and High speed mode.
Auto ....................... The built-in fans automatically run at a variable speed according to the internal temperature.
High ....................... The built-in fans run at a  xed high speed.
When you wish to cool down the temperature inside the projector quickly, select [High].
NOTE: It is recommended that you select High speed mode if you continue to use the projector for consecutive days.
Selecting Default Source [Default source select]
You can set the projector to default to any one of its inputs each time the projector is turned on.
Last ....................... Sets the projector to default to the previous or last active input each time the projector is turned on.
Auto ....................... Searches for an active source in order of Computer 1 → Computer 2 (Digital) → Computer 2 (Analog) 
→ Video → S-Video → Computer 1 and displays the  rst found source.
NOTE: The LV-7260/LV-X7 will search for an active source in order of Computer → Video → S-Video → 
Computer and displays the fi rst found source.
Computer 1 ........... Displays the RGB source from the Computer 1 Input [ANALOG IN-1] connector ever y time the projector 
is star ted up. (LV-7265 only)
Computer 2 (Digital)  ... Displays the DVI digital source from the Computer 2 Input [DIGITAL IN/ANALOG IN-2] (Digital) con-
nector ever y time the projector is star ted up. (LV-7265 only)
Computer 2 (Analog)  .. Displays the RGB source from the Computer 2 Input [DIGITAL IN/ANALOG IN-2] (Analog) connector 
ever y time the projector is star ted up. (LV-7265 only)
Computer .............. Displays the RGB source from the Computer Input [ANALOG IN] connector ever y time the projector is 
star ted up. (LV-7260/LV-X7 only)
Video ..................... Displays the Video source from the VIDEO IN connector ever y time the projector is star ted up.
S-Video ................. Displays the Video source from the S-VIDEO IN connector ever y time the projector is star ted up.
Enabling the deinterlace [Deinterlace]
Turns on or off the deinterlace function for a telecine signal.
On .......................... Default standard setting.
Off ......................... Select this option if there is any jitter or ar tifacts in video.
NOTE: This feature is not available for RGB, 480p, 576p, and HDTV signals.