Canon Lv-7365, Lv-7265, Lv-7260, Lv-x7 Multimedia Projector Users Manual

2
2. Installation and Connections
❶ Setting Up the Screen and the Projector
Selecting a Location (LV-7365/LV-7265)
The  further  your  projector  is  from  the  screen  or  wall,  the  larger  the  image.  The  minimum  size  the  image  can  be 
is  approximately  25"  measured  diagonally  when  the  projector  is  roughly  1.1  m  (3.5’)  from  the  wall  or  screen.  The 
largest the image can be is 300" when the projector is about 8.4 m (27.6’) from the wall or screen. Use the drawing...

3
2. Installation and Connections
Selecting a Location (LV-7260/LV-X7)
The  further  your  projector  is  from  the  screen  or  wall,  the  larger  the  image.  The  minimum  size  the  image  can  be 
is  approximately  25"  measured  diagonally  when  the  projector  is  roughly  1.1  m  (3.6’)  from  the  wall  or  screen.  The 
largest the image can be is 300" when the projector is about 8.8 m (28.9’) from the wall or screen. Use the draw-
ing below as a guide.
NOTE:
This projector can...


2. Installation and Connections
WARNING
• Installing your projector on the ceiling must be done 
by  a  qualified  technician.  Contact  your  dealer  for 
more information.
•  Do not attempt to install the projector yourself.
•  Only  use  your  projector  on  a  solid,  level  surface.  If 
the projector falls to the ground, you can be injured 
and the projector severely damaged.
•  Do  not  use  the  projector  where  temperatures  vary 
greatly. The projector must be used at temperatures...

5
2. Installation and Connections
❷ Making Connections
NOTE:  When  using  with  a  notebook  PC,  be  sure  to  connect  the  projector  and  notebook  PC  while  the  projector  is  in  standby 
mode and before turning on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered 
up.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or...

6
2. Installation and Connections
Using Two Analog COMPUTER Inputs Simultaneously (LV-7365/LV-7265)
If you need to use two analog inputs simultaneously, connect a VGA cable as shown below.
AUDIO INAUDIO OUTS-VIDEOINVIDEOINL
AUDIO INRSERVICE PORTANALOG IN-1DIGITAL IN /ANALOG IN-2
DIGITAL IN /ANALOG IN-2ANALOG IN-1
NOTE: When the DVI to VGA adapter is not to be used for an extended period of time, remove it from the projector. Failure to do 
so may cause damage to the connector of the projector.
iBM...

7
2. Installation and Connections
When Viewing a DVI Digital Signal (LV-7365/LV-7265)
To project a DVI digital signal, be sure to connect the PC and the projector using a DVI digital cable (not supplied) 
before turning on your PC or projector. Turn on the projector first and select Computer 2 (Digital) from the source 
menu before turning on your PC.
Failure  to  do  so  may  not  activate  the  digital  output  of  the  graphics  card  resulting  in  no  picture  being  displayed. 
Should this...

8
2. Installation and Connections
Connecting Your PC or Macintosh Computer (LV-7260/LV-X7)
NOTE: The ANALOG IN connector supports Plug & Play (DDC2).
S-VIDEOINVIDEOIN
L
AUDIO INRSERVICE PORT
ANALOG INANALOG INAUDIO IN 
PHONE
PHONE
Vga cable (supplied)to mini  d-s ub 15-pin connector on the projector. 
i t is recommended that you use a commercially 
available distribution amplifier if connecting a signal cable longer than the supplied one.
iBM PC or Compatibles ( desktop type)
or Macintosh ( desktop...

9
2. Installation and Connections
Connecting an External Monitor
AUDIO IN
AUDIO OUTS-VIDEOINVIDEOIN
L
AUDIO INRSERVICE PORT
ANALOG IN-1
DIGITAL IN /ANALOG IN-2
ANALOG IN 1
AUDIO IN 
S-VIDEOINVIDEOIN
L
AUDIO INRSERVICE PORT
ANALOG IN
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB ana-
log image you're projecting.
NOTE: Daisy chain connection is not possible.
NOTE:
• The  signal  from  the  DIGITAL  IN/ANALOG  IN-2  connector  cannot  be...

20
AUDIO IN
AUDIO OUTS-VIDEOINVIDEOIN
L
AUDIO INRSERVICE PORT
ANALOG IN-1
DIGITAL IN /ANALOG IN-2
AUDIO INL R
AUDIO OUT
LR
Component
Y Cb Cr
ANALOG IN-1AUDIO IN 
2. Installation and Connections
A component signal will be automatically displayed. If not, from the menu, select [Setup] → [Input signal select] → 
[Computer 1] or [Computer 2 (Analog)] ([Computer] on LV-7260/LV-X7) → [COMPONENT].
NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video...

2
2. Installation and Connections
AUDIO INL RAUDIO OUTLRVIDEO OUTS-VIDEOVIDEO
AUDIO IN
AUDIO OUTS-VIDEOINVIDEOIN
L
AUDIO INRSERVICE PORT
ANALOG IN-1
DIGITAL IN /ANALOG IN-2
VIDEO IN
AUDIO INS-VIDEO IN
Connecting Your VCR or Laser Disc Player
s-Video cable (not supplied)
Video cable (not supplied)
VCr/ l aser disc player
audio equipment
a udio cable (not supplied)
NOTE: The AUDIO IN L/MONO and R jacks (RCA) are shared between the Video and S-Video inputs.
NOTE: Refer to your VCR or laser disc player...