Canon Lv-7365, Lv-7265, Lv-7260, Lv-x7 Multimedia Projector Users Manual

							
2
. Introduction
❷ Introduction to the Projector
This section introduces you to your new projector and describes the features and controls.
Congratulations on Your Purchase of The Projector
The LV-7365/LV-7265/LV-7260/LV-X7 is one of the very best projectors available today. The projector enables you 
to  project  precise  images  up  to  300  inches  across  (measured  diagonally)  from  your  PC  or  Macintosh  computer 
(desktop or notebook), VCR, DVD player, document camera, or a laser disc player.
You can use the projector on a tabletop or cart, from behind a screen, or permanently mounted on a ceiling*1. The 
remote control can be used wirelessly.
*1  Do not attempt to mount the projector on a ceiling yourself.
  The  projector  must  be  installed  by  qualified  technicians  in  order  to  ensure  proper  operation  and  reduce  the 
risk of bodily injury.
  In addition, the ceiling must be strong enough to support the projector and the installation must be in accor
-
dance with any local building codes. Please consult your dealer for more information.
 
Features you'll enjoy:
•  Auto vertical keystone correction (LV-7365/LV-7265).
•  Built-in  Wall  Color  Correction  presets  provide  for  adaptive  color  correction  when  projecting  onto  non-white 
screen material.
•  Quick start & quick cool down.
  Eight seconds after turning on the power, the projector is ready to display PC or video images*.
  Powering down; The fans stop 30 seconds after turning off the power from the remote control or cabinet con
-
trol panel. The projector can be put away immediately after the projector is powered down.
  Also,  the  main  power  of  the  projector  can  be  turned  off  by  pressing  the  main  power  switch  or  unplugging  the 
power cord even during the cool down period after the projector is turned off.
*  If you turn on the projector immediately after the lamp is turned off or when the temperature is high, the fans 
runs without displaying an image for some time and then the projector will display the image.
•  DVI input connector (DVI-I 29 Pin) with HDCP compatible (LV-7365/LV-7265)
•  HDTV (1080i, 720p) and SDTV (576p, 480p) compatibility.
•  Color Management system.
•  Short focal length lens.
•  Display popular wide screen and full screen aspect ratios - 16:9 and 4:3.
•  Built-in speaker for an integrated audio solution.
•  High resolution display - up to UXGA compatible, XGA native resolution.
•  Multiple video mode selections (depending on your source).
•  Security feature prevents unauthorized individuals from displaying images.
•  You can control the projector with a PC or control system using the PC Control port (SERVICE PORT).
•  Easy set up and operation.
•  The contemporary cabinet design is light, compact and complements any office, boardroom Auditorium.
•  You can use the supplied wireless remote control and remote mouse receiver to operate your PC mouse from 
across  the  room.  The  remote  mouse  receiver  supports  almost  any  PC  using  a  USB  connection  (LV-7365, 
LV-7265 and LV-7260). 
						

							
3
About this user's manual
The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to 
review  the  user's  manual.  This  may  save  you  time  later  on.  At  the  beginning  of  each  section  of  the  manual  you'll 
find an overview. If the section doesn't apply, you can skip it.
• Microsoft,  Windows,  Windows  Vista,  and  PowerPoint  are  trademarks  or  registered  trademarks  of  Microsoft 
Corporation in the U.S. and other countries.
•  Macintosh, Mac, and PowerBook are trademarks of Apple Inc., registered in the U.S. and other countries.
•  VESA is a registered trademark of Video Electronics Standards Association.
. Introduction 
						

							

❸ Part Names of the Projector
MENUBACKKEYSTONE
WARNING    POWER AUTO PCINPUTLAMP
-+VOLVOL
MENUBACKKEYSTONE
WARNING    POWER AUTO PCINPUTVOL-VOL+
LAMP
AUDIO INAUDIO OUTANALOG IN-1DIGITAL IN /ANALOG IN-2
S-VIDEOINVIDEOINSERVICE  PORTRLAUDIO IN
Zoom l ever
( s ee page 28)Controls
(s ee page 6)
l ens
lens Cap
Be sure to remove the lens cap during 
projection. t he cap can deform or fire 
can occur.
Built-in security slot (  )*
focus r ing
( s ee page 28)
adjustable t ilt foot l ock Button
( s ee page 27)
a djustable t ilt foot
( s ee page 
27)
r emote sensor
( s ee page 10) Ventilation (inlet) / f
ilter Cover
( s ee page 
56)
d o not block this vent.
t roubles or fire can result.
t wo filters on l V-7365/lV-7265/ lV-7260
One filter on l V-X7
Ventilation (inlet)
Front/Top
aC i nputConnect the supplied power cord’s two-pin plug here, and 
plug the other end into an active wall outlet. ( see page 23)
Main Power s witch
When you plug the supplied power cord into an active wall outlet 
and turn on the Main Power, the POW er indicator turns orange 
and the projector is in standby mode.
(s ee page 24)
r
emote sensor
( l V-7365/ lV-7265)
( s ee page 
10)
t
erminal Panel
( s ee page 
7) Monaural s
peaker
( l V-7365/ lV-7265: 5W)
( l V-7260/ lV-X7: 1W)
Rear
*  This  security  slot  supports  the  MicroSaver  ®  Security  System.  MicroSaver  ®  is  a  registered  trademark  of 
Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc.
Ventilation (outlet)
heated air is exhausted from here.
do not block this vent. t roubles or 
fire can result.
. Introduction 
						

							
5
. Introduction
Bottom
a djustable t ilt foot
( s ee page 27)
adjustable t ilt foot l ock Button
( s ee page 27) l
amp Cover
( s ee page 
58)
r
ear f oot (left / r ight)
HINT: The Canon logo is on the panel of the projector cabinet . When projecting an image with the projector hung from the ceil-
ing, turn the Canon logo upside down.
To turn the logo upside down, follow the steps below.
1.	 Push	one	end	of	the	logo	gently.
  the other end will pop up slightly.
•  t he right drawing shows the part “C” is pressed gently.
•  t he part “n” on the other end will pop up.
2.	 Push	 and	hold	 the	end	 of	the	 logo	 gently	 and	rotate	 the	logo	 by	
holding	the	other	end.
•  t he right drawing shows that with the part “C” pressed the logo is 
rotated by holding the part “n” on the other end.
3.	 Release	your	hold	and	turn	the	logo	upside	down. 
						

							
6
. Introduction
Top Features
MENU
BACK
KEYSTONE
WARNING
    POWER 
AUTO PC
INPUT
VOL-VOL+
LAMP
3
4
1
5 8
92106
7
 .  POWER Button (  )
Use  this  button  to  turn  the  power  on  and  off  when 
the  main  power  is  supplied  and  the  projector  is  in 
standby mode.
To  turn  on  the  projector,  press  and  hold  this  button 
for  about  1  second.  To  turn  off  the  projector,  press 
this button twice.
2.  POWER Indicator
When this indicator is green, the projector is on; when 
this indicator is orange, it is in standby mode. See the 
Power Indicator section on page 61 for more details.
3.  WARNING Indicator
If  this  light  blinks  red  rapidly,  it  indicates  that  an  error 
has occurred, the lamp cover is not attached properly 
or  the  projector  has  overheated.  If  this  light  remains 
orange,  it  indicates  that  you  have  pressed  a  cabinet 
key while the Key lock is enabled. See the WARNING 
Indicator section on page 61 for more details.
 .  LAMP Indicator
If  this  light  blinks  red  rapidly,  it's  warning  you  that 
the  lamp  has  reached  the  end  of  its  usable  life.  After 
this  light  appears,  replace  the  lamp  as  soon  as  pos-
sible  (See  page 58).  If  this  is  lit  green  continually,  it 
indicates  that  the  lamp  mode  is  set  to  Quiet.  See  the 
Lamp Indicator section on page 61 for more details.
5.  INPUT Button
Selecting	from	INPUT	List
Press  and  quickly  release  the  INPUT  button  to  dis-
play  the  INPUT  list.  Each  time  the  INPUT  button  is 
pressed, the input source will  change as follows:
Computer  1* →  Computer  2  (Digital)* →  Computer  2 
(Analog)* → VIDEO → S-VIDEO → Computer 1* → ...
To display the selected source, press the OK button 
or allow 2 seconds to elapse. Detecting	the	Signal	Automatically
Press  and  hold  the  INPUT  button  for  a  minimum 
of  2  seconds,  the  projector  will  search  for  the  next 
available  input  source.  Each  time  you  press  and 
hold the INPUT button for a minimum of 2 seconds, 
the input source will change as follows:
Computer  1* →  Computer  2  (Digital)* →  Computer  2 
(Analog)* → VIDEO → S-VIDEO → Computer 1* → ...
* 
LV-7260/LV-X7:  Computer →  VIDEO →  S-VIDEO 
→ Computer → ...
6.  AUTO PC Button 
Use this button to adjust an analog RGB source for 
an optimal picture. See page 31.
7.  MENU Button
Displays the menu. See page 40, 41.
8.  SELECT 
 / VOL (+/–) Buttons
 See page 40.
 : Use  these  buttons  to  select  the  menu  of  the 
item you wish to adjust.
When no menus appear, these buttons work 
as a keystone control. See page 29.
 : Use  these  buttons  to  change  the  level  of  a 
selected  menu  item.  A  press  of  the   but-
ton  executes  the  selection.  When  no  menus 
a p p e a r,  t h e s e  b u t t o n s  w o r k  a s  a  vo l u m e 
control. See page 31.
9.  OK Button
Executes  your  menu  selection  and  activates  items 
selected from the menu.
 0.  BACK Button
Pr e s s i n g  t h i s  b u t t o n  w i l l  r e t u r n  t o  t h e  p r ev i o u s 
menu. 
While  you  are  in  the  main  menu,  pressing  this  but-
ton will close the menu. 
						

							
7
. Introduction
AUDIO IN
AUDIO OUT
S-VIDEOIN
VIDEOIN
L
AUDIO IN
RSERVICE PORT
ANALOG IN-1
DIGITAL IN /ANALOG IN-2
973128
456
Terminal Panel Features
 . Computer   Input Connector [ANALOG IN- ] (Computer 
Input  Connector  [ANALOG  IN]  on  LV-7260/LV-X7)  (Mini 
D-Sub  5 Pin)
Connect your computer or other analog RGB equip-
ment  such  as  IBM  compatible  or  Macintosh  com-
puters.  Use  the  supplied  VGA  cable  to  connect  to 
your  computer.  This  also  ser ves  as  a  component 
input  connector  that  allows  you  to  connect  a  com-
ponent  video  output  of  component  equipment  such 
as a DVD player. See page 15, 18, 20.
2.  Computer  2  Input  Connector  [DIGITAL  IN/ANA
-
LOG IN-2] (DVI-I 29 Pin) (LV-7365/LV-7265)
Connect  your  computer  or  other  analog  RGB  equip-
ment  such  as  IBM  compatible  or  Macintosh  comput-
ers.
Use  the  supplied  VGA  cable  to  connect  to  your  com-
puter. This also serves as a component input connec-
tor that allows you to connect a component video out-
put  of  component  equipment  such  as  a  DVD  player. 
See page 15, 16.
3. 
AUDIO IN Mini Jack (Stereo Mini) (LV-7365/LV-7265)
This  is  where  you  connect  the  audio  output  from 
your  computer  or  DVD  player  when  connected  to 
the  COMPUTER  input.  A  commercially  available 
audio cable is required. See page 15, 20.
 . 
Monitor Output Connector [  ] (Mini D-Sub  5 Pin)
You can use this connector to loop your computer im-
age to an external monitor from the RGB input source.
T h i s  c o n n e c t o r  o u t p u t s  R G B  s i g n a l  i n  s t a n d b y 
mode. See page 19.
5. AUDIO OUT Mini Jack (Stereo Mini) (LV-7365/LV-7265)
You  can  use  this  jack  to  output  sound  from  the  cur-
r e n t l y  s e l e c te d  s o u r c e  (C O M PU T ER ,  VI D EO  o r 
S-VIDEO).  Output  sound  level  can  be  adjusted  in  ac-
cordance with the sound level of the internal speaker.
Note that this cannot be used as a headphone jack.
(When  audio  equipment  is  connected,  the  projector 
speaker is disabled.)
When a cable mini-plug is inserted into this jack, both the 
right and left audio signals are not mixed, but separate.
For  example,  when  a  cable  mini-plug  is  inserted  into 
the left AUDIO IN jack only, only left sound is output.
6.  VIDEO IN Connector (RCA)
Connect  a  VCR,  DVD  player,  laser  disc  player,  or 
document camera here to project video. See page 21.
7.  S-VIDEO IN Connector (Mini DIN  Pin)
Here  is  where  you  connect  the  S-Video  input  from 
an external source like a VCR. See page 21.
NOTE: S-Video provides more vivid color and higher reso-
lution than the traditional composite video format.
 
8. AUDIO IN Jacks L /R (RCA)
These are your left and right channel audio inputs for 
stereo sound from a Video/S-Video source.
These jacks support an analog RGB audio source on 
LV-7260/LV-X7. See page 18, 21.
9.  SERVICE PORT (Mini DIN 8 Pin)
Use  this  port  to  connect  a  PC  or  control  system  to 
control the projector via an optional RS-232C serial 
cable  (LV-CA34).  If  you  are  writing  your  own  pro-
gram, typical PC control codes are on page 71.
LV-7365/LV-7265
S-VIDEOIN
VIDEOIN
L
AUDIO IN
RSERVICE PORT
ANALOG IN
97
1468
LV-7260/LV-X7 
						

							
8
. Introduction
❹ Part Names of the Remote Control
 .  Infrared Transmitter
  Direct the remote control toward the remote sensor 
on the projector cabinet.
2.  POWER Button
  When the main power is on, you can use this button 
to turn your projector on.
NOTE: To turn on the projector, press and hold the POWER 
button for about 1 second.
 You can use this button to turn your projector off.
NOTE: To turn off the projector, press this button twice.
3.  INFO. Button
  Provides  the  information  on  the  current  signal  and 
projector settings. See page 54.
 .  IMAGE Button
  Press  this  button  to  display  the  Image  adjustment 
menu  to  adjust  Image  mode,  Contrast,  Brightness, 
S har p nes s,  C o lor  level  and  C o lor  balan c e.  See 
pages 45 to 46.
BACK
R-CLICKL-CLICK
VOL
FREEZE
D.ZOOMPAGE
MENU
POWER
RD-428E
INPUTIMAGE
ASPECT
INFO.
NO SHOW
AUTO PC
1
2
46
78
3
5
13
11
15
14
12
17
1816
9
10
5. INPUT Button
	 Selecting	from	INPUT	List
Press  and  quickly  release  the  INPUT  button  to  dis-
play  the  INPUT  list.  Each  time  the  INPUT  button  is 
pressed, the input source will change as follows:
Computer  1* →  Computer  2  (Digital)* →  Computer  2 
(Analog)* → VIDEO → S-VIDEO → Computer 1* → ...
To display the selected source, press the OK button 
or allow 2 seconds to elapse.
Detecting	the	Signal	Automatically
Press  and  hold  the  INPUT  button  for  a  minimum 
of  2  seconds,  the  projector  will  search  for  the  next 
available  input  source.  Each  time  you  press  and 
hold the INPUT button for a minimum of 2 seconds, 
the input source will change as follows:
Computer  1* →  Computer  2  (Digital)* →  Computer  2 
(Analog)* → VIDEO → S-VIDEO → Computer 1* → ...
* 
LV-7260/LV-X7:  Computer →  VIDEO →  S-VIDEO 
→ Computer → ...
6.  AUTO PC Button
  Use this button to adjust an analog RGB source for 
an optimal picture. See page 31.
7.  ASPECT Button
  Press  this  button  once  to  display  the  Aspect  select 
menu. Keep pressing will change aspect ratios. See 
page 46.
8.  NO SHOW Button
  This  but ton  turns  of f  the  image  and  sound  for  a 
short  period  of  time.  Press  again  to  restore  the  im-
age and sound. See page 34.
9.  MENU Button
  Displays  the  menu  for  various  settings  and  adjust
-
ments. See page 40, 41.
 0.  SELECT 
 (Mouse) Button
See page 40.
:  Use  these  buttons  to  select  the  menu  of  the 
item you wish to adjust.
: Use  these  buttons  to  change  the  level  of  a 
selected menu item. A press of the  button 
executes the selection.
  When an image is magnified, the SELECT 
 
button moves the image. See page 34.
  This button also works as a computer mouse when 
the  supplied  remote  mouse  receiver  is  connected 
with your computer. See page 36. (This button can-
not be used as a computer mouse for LV-X7.) 
						

							
9
BACK
R-CLICKL-CLICK
VOL
FREEZE
D.ZOOMPAGE
MENU
POWER
RD-428E
INPUTIMAGE
ASPECT
INFO.
NO SHOW
AUTO PC
1
2
46
78
3
5
13
11
15
14
12
17
1816
9
10
. Introduction
 . OK Button
  Use  this  but ton  to  enter  your  menu  selec tion.  It 
works  the  same  way  as  the  OK  button  on  the  cabi-
net. See page 6.
 2.  BACK Button
  It  works  the  same  way  as  the  BACK  button  on  the 
cabinet. See page 6.
 3.  L-CLICK Button
  (This button cannot be used for LV-X7.)
  This  button  works  as  the  mouse  left  button  when 
the  supplied  remote  mouse  receiver  is  connected 
with your computer. See page 36.
 . R-CLICK Button
  (This button cannot be used for LV-X7.)
  This  button  works  as  the  mouse  right  button  when 
the  supplied  remote  mouse  receiver  is  connected 
with your computer. See page 36.
 5.  VOL (+) (–) Button
  Pres s  (+)  to  in c rease  t he  vo lume  and  (–)  to  d e
-
crease it. See page 31. 
6.  PAGE 
▲/▼ Button
  (This button cannot be used for LV-X7.)
  Use  these  buttons  to  operate  your  computer  with 
the  supplied  remote  mouse  receiver.  See  page 36. 
You  can  use  these  but tons  to  scroll  the  viewing 
area  of  the  window  or  to  move  to  the  previous  or 
next slide in PowerPoint on your computer.
 7.  D. ZOOM (+) (–) Button
  U s e  t h i s  b u t t o n  t o  a d j u s t  t h e  i m a g e  s i z e  u p  t o 
400%.
  T he  imag e  i s  mag nifie d  a b out  t he  c enter  of  t he 
screen. See page 34.
 8.  FREEZE Button
  This  button  will  freeze  a  picture.  Press  again  to  re
-
sume motion. See page 34. 
						

							
0
. Introduction
Remote Control Precautions
•  Handle the remote control carefully.
•  If the remote control gets wet, wipe it dry immediately.
•  Avoid excessive heat and humidity.
•  Do not heat, take apart, or throw batteries into fire.
•  Ensure that you have the batteries' polarity (+/-) aligned correctly.
•  If you will not be using the remote control for a long time, remove the batteries.
•  Do not place the batteries upside down.
•  Do not use new and old batteries together, or use different types of batteries together.
•   Dispose of used batteries according to your local regulations.
Operating Range for Wireless Remote Control
Battery Installation
Press  firmly  and  slide  the 
battery cover off.
2Remove  both  old  batteries  and 
install  new  ones  (AAA).  Ensure 
that  you  have  the  batteries'  po-
larity (+/–) aligned correctly.
3Slip  the  cover  back  over  the  bat-
teries until it snaps into place. Do 
not  mix  different  types  of  batter-
ies or new and old batteries.
remote sensor on projector cabinet
7m/22 feet
•  The  infrared  signal  operates  by  line-of-sight  up  to  a  distance  of  about  7  m  (22  feet)  and  within  a  60-degree 
angle of the remote sensor on the projector cabinet.
•  The projector will not respond if there are objects between the remote control and the sensor, or if strong light 
falls on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.
NOTE: The LV-7260 and LV-X7 do not have the remote sensor on the rear panel.
30°
remote control r
emote sensor on projector cabinet
7m/22 feet
7m/22 feet
7m/22 feet
30°
30°
30°
30°
30°
30°
30°
remote control
Horizontal rangeVertical range 
						

							

This section describes how to set up your projector and how to connect video and audio sources.
2. Installation and Connections
Your projector is simple to set up and use. But before you get started, you must first:
① Set up a screen and the projector. See page 12, 13.
② Connect your computer or video equipment to the projector. See pages 15, 16, 17, 18, 19, 20, 21, 22.
③ Connect the supplied power cord. See page 23.
NOTE: Ensure that the power cord and any other cables are disconnected before moving the projector. When moving the projec-
tor or when it is not in use, cover the lens with the lens cap.
to the wall outlet.