Canon network camera VBC50FSi User Manual

							
xi
FCC NOTICE
Network Camera, Model Name: VB-C50FSiN, VB-C50FSiP, VB-C50FiN, VB-C50FiP\
This device complies with Part 15 of the FCC Rules. Operation is subject\
 to the
following two conditions: (1) This device may not cause harmful interf\
erence,
and (2) this device must accept any interference received, including i\
nterference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for \
a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limi\
ts are
designed to provide reasonable protection against harmful interference i\
n a
residential installation. This equipment generates, uses and can radiate\
 radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a par\
ticular
installation. If this equipment does cause harmful interference to radio\
 or
television reception, which can be determined by turning the equipment o\
ff and
on, the user is encouraged to try to correct the interference by one or \
more of
the following measures:
 - Reorient or relocate the receiving antenna.
 - Increase the separation between the equipment and receiver.
 - Connect the equipment into an outlet on a circuit different from that to\
 which the receiver is connected.
 - Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpa\
rt B of
Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwi\
se
specified in the manual. If such changes or modifications should be made\
, you
could be required to stop operation of the equipment.
Canon U.S.A. Inc.
One Canon Plaza, Lake Success, NY 11042, U.S.A.
Tel No. (516) 328-5600
a Safe Use of Equipment
Canadian Radio Interference Regulations
This Class B digital apparatus complies with Canadian ICES-003.
Réglementation canadienne sur les intérferences radio
Cet appareil numérique de la classe B est conforme à la norme NMB-\
003 du
Canada.
Dieses Produkt ist zum Gebrauch im Wohnbereich, Geschäfts- und
Gewerbebereich sowie in Kleinbetrieben vorgesehen.
FDA regulation
This Network Camera has not been evaluated by the Food and Drug Administ\
ration
(FDA) for use as a medical device. When incorporated into a system wit\
h medical
applications, FDA regulations may apply. Therefore, please consult your \
legal
advisor to determine whether FDA regulations apply.
C
O
P
Y  
						

							
xii
a IMPORTANT SAFETY INSTRUCTIONS
In these safety instructions, the word
“equipment” refers to the Canon Network
Camera VB-C50FSi/VB-C50Fi and all its
accessories.
1. Read Instructions - All the safety and
operating instructions should be read before
the equipment is operated.
2. Retain Instructions - The safety and operating
instructions should be retained for future
reference.
3. Heed Warnings - All warnings on the
equipment and in the operating instructions
should be adhered to.
4. Follow Instructions - All operating and
maintenance instructions should be followed.
5. Cleaning - Unplug this equipment from the wall outlet before cleaning.
Wipe the equipment with a clean soft cloth. If
necessary, put a cloth in diluted neutral
detergent and wring it well before wiping the
equipment with it. Finally, clean the
equipment with a clean dry cloth. Do not use
benzene, thinner or other volatile liquids or
pesticides as they may damage the product’s
finish. When using chemically-treated
cleaning cloths, observe those precautions
accordingly.
6. Accessories - Do not use accessories not recommended in this manual as they may
be hazardous. Always use specified
connection cables. Connect devices correctly.
7. Water and Moisture - Hazard of electric shock
- Do not use the equipment near water or in
rainy/moist situations. Do not put a heater
near this equipment.
8. Placing or Moving - Do not place on an
unstable cart, stand, tripod, bracket or table.
The equipment may fall, causing serious
injury to a child or adult, and
serious damage to the
equipment. An equipment and
cart combination should be
moved with care. Quick stops, excessive force, and uneven
surfaces may cause the equipment and cart
combination to overturn.
9. Power Sources - The PA-V16 AC adapter should be operated only from the type of power
source indicated on the marking label. If you
are not sure of the type of power supply to your
home, consult your equipment dealer or local
power company.
10. Polarization - The PA-V16 AC adapter is
equipped with a polarized 2-prong plug (a plug
having one blade wider than the other).
The 2-prong polarized plug will fit into the
power outlet only one way. This is a safety
feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If
the plug still fails to fit, contact your electrician
to replace your obsolete outlet. Do not defeat
the safety purpose of the polarized plug.
11. Power Cord Protection - Power cords should be routed so that they are not likely to be
walked on or pinched by items placed upon
or against them. Pay particular attention to
plugs and the point from which the cords exit
the equipment.
12. Outdoor Antenna Grounding - If an outside antenna is connected to the equipment, be
sure the antenna is grounded so as to provide
some protection against voltage surges and
built-up static charges. Section 810 of the
National Electrical Code, ANSI/NFPA No.70-
1984, provides information with respect to
proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding
conductors, location of antenna, antenna
discharge unit, connection to grounding
electrodes, and requirements for the
grounding electrode. See figure 1.
a Safe Use of Equipment
C
O
P
Y  
						

							
xiii
fig-1
EXAMPLE OF ANTENNA GROUNDING AS 
PER NATIONAL ELECTRICAL CODEANTENNA 
LEAD IN WIRE
ANTENNA 
DISCHARGE 
UNIT (NEC 
SECTION 810-20)GROUNDING 
CONDUCTORS 
(NEC SECTION 
810-21)
GROUNDING CLAMPS
POWER SERVICE 
GROUNDING ELECTRODE 
SYSTEM
(NEC ART 250. PART H)
NEC — NATIONAL ELECTRIC CODE ELECTRIC 
SERVICE 
EQUIPMENTGROUNDING 
CLAMP
13.
Lightning - For added protection of this
equipment during a lightning storm, or when
it is left unattended and unused for long
periods of time, disconnect it from the wall
outlet and disconnect the antenna. This will
prevent damage to the equipment due to
lightning and power-line surges.
14. Power Lines - An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light
or power circuits, or where it can fall into such
power lines or circuits. When installing an
outside antenna system, extreme care should
be taken to keep from touching such power
lines or circuits as contact with them might
be fatal.
15. Overloading - Do not overload wall outlets and
extension cords as this can result in a risk of
fire or electric shock.
16. Object and Liquid Entry - Never push objects of any kind into this equipment through
openings as they may touch dangerous
voltage points or short out parts that could
result in a fire or electric shock. Be careful
not to spill liquid of any kind onto the
equipment.
17. Servicing - Do not attempt to service this
equipment yourself as opening or removing
covers may expose you to dangerous voltage
or other hazards. Refer all servicing to
qualified personnel. 18. Damage Requiring Service - Disconnect this
equipment from the wall outlet and all power
sources including batteries, and refer
servicing to qualified service personnel under
the following conditions.
a. When the power-supply cord or plug is
damaged.
b. If any liquid has been spilled onto, or
objects have fallen into, the equipment.
c. If the equipment has been exposed to rain or water.
d. If the equipment does not operate normally
even if you follow the operating instructions.
Adjust only those controls that are covered
by the operation instructions. Improper
adjustment of other controls may result in
damage and will often require extensive
work by a qualified technician to restore
the equipment to its normal operation.
e. If the equipment has been dropped or the cabinet has been damaged.
f. When the equipment exhibits a distinct
change in performance. This indicates a
need for service.
19. Replacement Parts - When replacement parts
are required, be sure the service technician
has used replacement parts that are specified
by Canon or that have the same
characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock or other hazards.
20. Safety Check - Upon completion of any
service or repairs to this equipment, ask the
service technician to perform safety checks
to determine that the equipment is in safe
operating order.
21. Do not install the equipment in the following locations as this can cause a fire or electric
shock:
 - Hot locations
 - Close to a fire
 - Very humid or dusty locations
a Safe Use of Equipment
C
O
P
Y  
						

							
xiv
 - Locations exposed to direct sunlight
 - Locations exposed to salt spray
 - Close to flammable solvents (alcohol,
thinners, etc.)
22. When any of the following occurs,
immediately switch OFF the equipment,
unplug it from the main power supply and
contact your nearest Canon supplier. Do not
continue to use the equipment as this can
cause a fire or electric shock.
 - The equipment emits any smoke, heat,
abnormal noise, or unusual odor.
 - A metal object falls into the equipment.
 - The equipment is damaged in some way.
23. Please observe the following when using the equipment. Failure to do so can result in a
fire or electric shock.
 - Do not use flammable sprays near the
equipment.
- Do not subject the equipment to strong
impacts.
24. Make sure the power line and network cable are implemented in a safe manner
accordingly to the related technical
regulations.
25. Focusing on the direct sunlight, halogen
lamp or any other high-intensity lamp for a
long time may cause  damage to the image
sensor.
a Safe Use of Equipment
For CA, USA only
Included lithium battery contains Perchlorate Material – special hand\
ling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate/ for details.
C
O
P
Y  
						

							
xv
a Safe Use of Equipment
a Notes on Using PoE Hubs
a CAUTION:
● Only use IEEE 802.3af-compliant PoE hubs or midspans.
●  When both of a PoE hub and the AC Adapter are connected to the VB-C50FSi\
,
it runs on the power supply from the PoE hub.
●  Some PoE hubs allow the current used by each port to be restricted, but \
the
VB-C50FSi may not operate correctly when such restrictions are applied. \
Do
not use such restrictions with the VB-C50FSi.
●  Some PoE hubs allow the total current consumed on each port to be restri\
cted,
but the hub may not operate correctly if multiple ports are used.
Refer to the users manual for your PoE hub.
●  Use a cable that conforms to the category 5 or higher standard as the LA\
N
cable (max. 100 m).
Note
Notes on Using the Motion Detection Function and VBCollector
The Motion Detection Function ( → P.4-37) and VBColletor ( → P.6-11) are not suited
to applications where high levels of reliability are required. Therefore\
, we recommend
that you not use these functions for monitoring or other purposes if con\
sistently high
levels of reliability are required. Canon accepts no liability whatsoeve\
r for faults
resulting from the use of the Motion Detection Function and VBCollector.\
Max.100 m
Midspan Hub PoE hub
C
O
P
Y  
						

							
xvi
Maintenance
Cleaning the Equipment
1. Unplug the AC adapter from the wall outlet.If you are using a PoE hub or midspan, disconnect the
LAN cable also (VB-C50FSi only).
2. Carefully wipe the equipment with a soft cloth that has been moistened with water or a mild detergent.
a WARNING:
Do not use flammable solvents such as alcohol, benzene or thinners.
The use of such substances can cause a fire or electric shock.
3. Wipe with a dry cloth.
4. When you have finished, plug the AC adapter back in to the wall outlet.
Cleaning the Lens
Use a commercially available lens cleaner to remove any soiling from the\
 lens.
● The auto-focus may not function correctly if the surface of the lens is \
dirty.
● Scratches on the surface of the lens will cause image defects.
Icons Used in This Instruction Manual
Note
Indicates important information that must be observed or actions that ar\
e prohibited
during an operation. These notes must be read to prevent possible faults\
 or damage
to the equipment.
Tip
Indicates supplementary information or a reference to an operation. User\
s are advised
to read these memos.
Refer to the PDF manual on the supplied CD-ROM.
d
C
O
P
Y  
						

							
Before Using the
VB-C50FSi/VB-C50Fi
This chapter describes the features of the VB-C50FSi/VB-
C50Fi, the hardware and software requirements, and the
name and functions of the system components.
Chapter
C
O
P
Y  
						

							
1-2
The VB-C50FSi/VB-C50Fi is a system that distributes live videos via the \
Internet or an intranet. It
can be used in a wide range of applications, such as distributing live v\
ideos from a Web site or
monitoring. The system is configured for the VB-C50FSi/VB-C50Fi and view\
er software. Please
use the supplied viewer software for viewing videos distributed by the V\
B-C50FSi/VB-C50Fi and
controlling cameras
 (→  P.1-4, 2-14).
 Broadband Video Distribution function
The VB-C50FSi/VB-C50Fi is capable of capturing videos at up to 30 fps (\
NTSC)/25 fps (PAL).
Motion-JPEG type is used to compress video images. For networking, auto-\
negotiation between
Ethernet 100Base-TX/10Base-T is provided and a leased line or ADSL can a\
lso be used through
a router. Since video quality and the frame rate can be freely set, vide\
os can be distributed under
conditions that best suit the network bandwidth.
*Please refer to P.1-10 to confirm whether your VB-C50FSi/VB-C50Fi is PAL\
 model or NTSC model.
Concurrent video is distributed up to 50 clients
Up to 50 clients can view video at the same time from a single VB-C50FSi\
/VB-C50Fi.
High-performance 26x zoom camera and video distribution server functions\
housed in a single unit
The camera capable of full zoom function (high-performance 26x zoom) a\
nd its server functions
for distributing videos through a network are compactly housed in a sing\
le unit. By simply connecting
a LAN cable and a power supply, the unit can distribute live videos from\
 any location* where it is
installed.
*The unit cannot be installed in locations subject to direct sunlight, hi\
gh temperatures, high humidity, or
other adverse conditions ( → P.xiii, xiv).
Can be mounted on ceilings, etc.
The VB-C50FSi/VB-C50Fi can be installed on the ceiling or a wall using a\
 mounting arm*.
*The unit cannot be installed in locations subject to direct sunlight, hi\
gh temperatures, high humidity, or
other adverse conditions ( → P.xiii, xiv).
Built-in PoE (Power over Ethernet) function (VB-C50FSi)
By using an IEEE 802.3af-compliant PoE hub or midspan, power can be supp\
lied to the VB-
C50FSi via a LAN cable. This simplifies the installation process since t\
here is no need to fit power
outlets at each camera location.
*Use only approved PoE hubs or midspans. ( → P.2-6)
* The LAN cable used to connect the VB-C50FSi to a PoE hub or midspan sh\
ould be no more than 100
meters long.
Remote camera control from the viewer
The VB-C50FSi/VB-C50Fi comes with two types of viewer software: the View\
er for PC and the
Viewer for Java. The viewers give you full remote control of the camera \
zoom magnification of the
VB-C50FSi/VB-C50Fi, allowing you to view videos with plenty of ambiance.\
Shade Correction function
If the background of an image is bright, making the subject difficult to\
 see, you can adjust the
contrast of the darker areas to make it easier to see. Unlike backlight \
compensation, the shade
correction feature allows image processing without adversely affecting t\
he existing lighter regions.
Features of the VB-C50FSi/VB-C50Fi
C
O
P
Y  
						

							
1-3
Before Using the VB-C50FSi/VB-C50Fi
Features of the VB-C50FSi/VB-C50Fi
Zoom Position Preset function
If often-used camera zoom positions and related items are saved in advan\
ce as presets, the
camera can be controlled from the viewer by simply selecting a desired p\
reset. Up to 10 presets
can be stored.
View Restriction function
You can set restrictions on camera zoom magnifications. For example, if \
the VB-C50FSi/VB-
C50Fi is showing camera footage on the Internet, it is possible to distr\
ibute videos while protecting
privacy (→ P.iii, “Request concerning disclosure of live videos and audio”)\
.
More powerful security functions
The destinations for video distributions can be restricted based on pass\
words. Up to 50 clients
can be registered.
Using preset schedules or links with external devices to record pictures\
 or
audio*
Using the Multi-Terminal Module ( → P.1-11), you can set picture and audio recording* based on
ON/OFF input from an external device and from previously-set schedules. \
If VBCollector is used,
images and 
sound recorded* by the VB-C50FSi/VB-C50Fi can be automatically collected\
 so that
you can view the images and 
play back the audio data* on a PC.
* Audio recording and Audio Playback functions are only available on the V\
B-C50FSi.
* Only available with a particular model of the VB-C50FSi ( → P.iii)
Audio Playback (VB-C50FSi)
Using the Multi-Terminal Module ( → P.1-11), you can connect a speaker with amp to the camera.
Then, you can register your favorite audio files or sample files recorde\
d on a CD-ROM and play
the registered files based on ON/OFF input from an external device and f\
rom previously-set
schedules.
Audio transmission (VB-C50FSi)
Using the Multi-Terminal Module ( → P.1-11), you can connect a microphone* and speaker with
amp to the camera and then send and receive 
audio* via the Viewer.
*
 Only available with a particular model of the VB-C50FSi ( → P.iii)
Night mode shooting
By canceling the infrared cut filter, you can increase the camera’s s\
ensitivity and take pictures
even in very dimly lit situations.
Motion detection function
You can perform external device control, video and audio recording* by detecting changes in the
image caused by motion of people or objects.
*
 Only available with a particular model of the VB-C50FSi ( → P.iii)
Service settings with schedule function
You can start up motion detection and external device services by settin\
g up a visual and easy-
to-understand schedule in the calendar.
C
O
P
Y  
						

							
1-4
Hardware and Software Requirements
Viewer Software (→ d  Viewer Software User’s Manual)
The viewer software that is supplied with the VB-C50FSi/VB-C50Fi lets yo\
u view the video captured
by the VB-C50FSi/VB-C50Fi and control the camera. For the latest information, please refer to Canon Web site.
Note
●The manual for the viewer software is on the supplied CD-ROM (Viewer-E.\
pdf).
● Although older versions of viewers can be used, some of the features are\
 different.
Therefore, we recommend you to use the latest version.
Viewer for PC Ver. 3.6
Operating System/Windows 2000(SP4) / Internet Explorer 6.0(SP1), Netscape 7.1 or 7.2Web BrowserWindows XP(SP1a) / Internet Explorer 6.0(SP1), Netscape 7.1 or 7.2
Windows XP(SP2) / Internet Explorer 6.0(SP2) or 7.0, Netscape 7.1 or\
 7.2
Windows Server 2003 Standard Edition / Internet Explorer 6.0, Netscape 7\
.1 or 7.2
Windows Server 2003 Standard Edition (SP1)
/ Internet Explorer 6.0(SP1) or 7.0, Netscape 7.1 or 7.2
Windows Server 2003 Standard Edition (SP2) / Internet Explorer 6.0(SP\
2) or 7.0
Windows Server 2003 R2 Standard Edition / Internet Explorer 6.0(SP1) o\
r 7.0
Windows Server 2003 R2 Standard Edition (SP2) / Internet Explorer 6.0(\
SP2) or 7.0
* Must be installed from the supplied CD-ROM ( → P.2-13).
Viewer for Java Ver. 3.6
Operating System/Windows 2000(SP4) / Internet Explorer 6.0(SP1), Netscape 7.1 or 7.2Web BrowserWindows XP(SP1a) / Internet Explorer 6.0(SP1), Netscape 7.1 or 7.2
Windows XP(SP2) / Internet Explorer 6.0(SP2) or 7.0, Netscape 7.1 or\
 7.2
Windows Server 2003 Standard Edition / Internet Explorer 6.0, Netscape 7\
.1 or 7.2
Windows Server 2003 Standard Edition (SP1)
/ Internet Explorer 6.0(SP1) or 7.0, Netscape 7.1 or 7.2
Windows Server 2003 Standard Edition (SP2) / Internet Explorer 6.0(SP\
2) or 7.0
Windows Server 2003 R2 Standard Edition / Internet Explorer 6.0(SP1) o\
r 7.0
Windows Server 2003 R2 Standard Edition (SP2) / Internet Explorer 6.0(\
SP2) or 7.0
Java VM MSVM Release 5.0.0.3810 (Java VM provided by Microsoft)
Java Plug-in 1.4.2 (Java VM provided by Sun Microsystems)
* Java VM must be installed beforehand. If the Java VM provided by Microso\
ft has not been installed,
please access Sun Microsystems Website to download the Java VM provided \
by Sun Microsystems.
* Not compatible with Java Plug-in 1.5.0 or later (Java VM provided by Su\
n Microsystems).
* This viewer may not run stably on operating systems and Web browsers oth\
er than those listed above.
C
O
P
Y