Canon network camera VBM641VE User Manual

Setting Page
4
81
[White Balance]
Select the white balance according to the light  source to achieve natural color in the video.
For details, please refer to “White Balance” in “Use Control for Admin” (P. 164).
[Noise Reduction]
Select a noise reduction level.
For details, please refer to “I mage Quality Adjustment” in “U se Control for Admin” (P. 168).
[ Sharpness]
Select a sharpness level.
For details, please refer to “I mage Quality Adjustment” in “U se Control for Admin” (P. 168).
[Color...

82
Reduces the size of transmitted H.264 video by reducing the video quality of non-target areas, such as ceilings and the sky.
ADSR is an abbreviation for Area-specific Data Size Reduction.
Note
 The quality of the specified area is determined by [Video Settings] > [H.264(1)] or [H.264(2)].
 Even if the camera is panned, tilted, or zoomed, th e specified area follows the movement of the camera.
 Specified areas can only be config ured within view restrictions.
Specified Area
Specify the area where video...

Setting Page
4
83
If you select [Enable] for the area with the frame color you  would like to use for the specified area, the frame will appear on  
the Viewer.
Set the specified area as follows with the display area.
 Drag out a frame and move it to the area you want to specify.
 Change the size of the frame by dragging any of the 8 handles ( ■).
 If you want to change the camera angle, use the pan/tilt/zoom sliders.
[Preview] 
The camera will move to a specified area  if you click [Preview] for that...

84
ADSR
Set whether H.264(1) and H.264(2) will each lower video quality outside areas set with [Specified Area].
[Enable in H.264(1)]
Select [Enable] to lower video quality outside areas set with [Specified Area] in H.264(1) video.
[Enable in H.264(2)]
Select [Enable] to lower video quality outside areas set with [Specified Area] in H.264(2) video.
Important
If you use [ADSR] with [H.264(1)], H.264(1) video cannot  be uploaded or recorded to a memory card. 

Setting Page
4
85
Displays the date and time, camera nam e and other UI strings on the Viewer.
Note
 Depending on video quality settings, on-screen display may beco me difficult to decipher. Set after confirming appearance on actual 
video.
 When using digital PTZ, on-screen display wi ll not appear if the cropped video has a horizontal size of 384 pixels or less. 
On-Screen Display
[Date display]
Select whether to display the date on the Viewer.
[Position of date display]
Select position for date...

86
[Text string display]
If [Text display] is set to [Display designated string], enter the text string to  be displayed in alphanumeric characters.
[Color of text]
Select from eight colors for the text color.
[Background color]
Select from eight colors for the background color.
[Color depth of text and background]
Select a color depth combination (Filling, Transparence,  Translucence) for the text and background color. 

Setting Page
4
87
Settings for audio input from the microphone connected to the  camera and audio output from the Viewer. The output sound 
clip used when an event is tr iggered can also be registered.
This [Audio Settings] submenu is common with the [Audio Settings] submenu found in the [Event] menu.
Settings configured in any page will be reflected in the other pages.
General Sound
Set the audio input/output volume, e cho cancellation and microphone type.
[Input Volume]
Enter the input volume from the...

88
Sound Clip Upload1to 3
You can upload up to three sound clips for playback when an event is triggered.
Note
The sound clip is used when audio playback is set in [Event] > [External Device Input] (P. 104) or [Intelligent Function Setting  Tool] > 
[Event] tab (P. 228).
[Browse File]
Specify the sound clip to upload and click [Add].
To be able to upload a sound clip, it must satisfy the following requirements.
 Playback length: Less than 20 seconds.
 File Format: “.wav” (µ-law PCM 8bit. Sampling...

Setting Page
4
89
Settings for HTTP server, SNMP server, FTP  server usage or WS-Security time checks.
HTTP Server
Set the authentication method and HTTP port number.
[Authentication Method]
Select an authentication method for use by the HTTP server.
[HTTP Port]
Enter an HTTP port number.
Normally use [80] (factory default setting).
[HTTP S Port]
Enter an HTTPS port number.
Normally use [443] (factory default setting).
SNMP Server
Configure the necessary settings to use SNMP.
Note
 The camera information...

90
It is recommended that you change the default community name from [public] to ensure system security.
[Administrator Contact Information]
Enter contact information (e-mail address, etc.) for the administrator of the camera.
Setting information can be referenced by the SNMP manager.
[Administration  Function Name]
Enter the camera name used for administration.
Setting information can be referenced by the SNMP manager.
If left blank, the camera model name will be used.
[Installation Location]
Enter...