Casio Pag240t7 Manual

1
Operation Guide 3173 3246
Congratulations upon your selection of this CASIO watch.
ApplicationsThe built-in sensors of this watch measure direction, barometric pressur\
e, temperature and altitude. 
Measured values are then shown on the display. Such features make this w\
atch useful when hiking, 
mountain climbing, or when engaging in other such outdoor activities.Warning !
• The measurement functions built into this watch are not intended for ta\
king measurements that require professional or...

2
Operation Guide 3173 3246
Mode Reference Guide
Your watch has 10 “modes”. The mode you should select depends on w\
hat you want to do.To do this:Enter this mode:• View the current date in the Home City• Confi gure Home City and daylight saving time (DST) settings• Confi gure time and date settingsTimekeeping Mode
View the sunrise and sunset times for a specifi c date Sunrise/Sunset Mode
• Determine your current bearing or the direction from your current locat\
ion to a  destination as a direction...

3
Operation Guide 3173 3246
Confi guring Current Time and Date Settings
You can use the procedure below to adjust the Timekeeping Mode time and \
date settings if they are off.
To change the current time and date settings
1. In the Timekeeping Mode, hold down  E
 until the currently selected 
city code starts to fl ash. This is the city code setting screen.
• Before the city code starts to fl ash, the message  SET Hold
will appear on the display. Keep  E
 depressed until  SET Hold
disappears and the city...

4
Operation Guide 3173 3246
Bearing MemoryBearing Memory lets you store a direction reading and display that 
reading as you take subsequent digital compass measurements. The 
Bearing Memory screen displays the direction angle for the stored 
direction, along with an indicator on the display that also indicates th\
e 
stored direction. 
When you take digital compass measurements while the Bearing Memory 
screen is on the display, the direction angle of the current digital com\
pass 
measurement (as read...

5
Operation Guide 3173 3246
The following shows how to interpret the data that appears on the barome\
tric pressure graph.
A rising graph generally means improving weather.
A falling graph generally means deteriorating weather.
Note
• If there are sudden changes in weather or temperature, the graph line o\
f past  measurements may run off the top or bottom of the display. The entire gr\
aph will 
become visible once barometric conditions stabilize.
• The following conditions cause the barometric pressure...

6
Operation Guide 3173 3246
Using the Altitude Differential Value While Mountain Climbing or HikingAfter you specify the altitude differential start point while mountain c\
limbing or hiking, you easily can 
measure the change in the altitude between that point and other points a\
long the way.
To use the altitude differential value1. In the Altimeter Mode, check to make sure that an altitude reading is\
 on the display.
• If an altitude reading is not displayed, press  A
 to take one. See “To 
take an...

7
Operation Guide 3173 3246
Specifying Temperature, Barometric Pressure, and Altitude Units
Use the procedure below to specify the temperature, barometric pressure,\
 and altitude units to be used in 
the Barometer/Thermometer Mode and the Altimeter Mode.Important!
WhenTYO
 (Tokyo) is selected as the Home City, the altitude unit is set 
automatically to meters ( m
), the barometric pressure unit to hectopascals 
( hPa
), and the temperature unit to Celsius ( °C
). These settings cannot 
be changed.
To...

8
Operation Guide 3173 3246
To confi gure longitude and latitude settings
1. In the Timekeeping Mode, hold down  E
 until the currently selected 
city code starts to fl ash. This is the city code setting screen.
• Before the city code starts to fl ash, the message  SET Hold
will appear on the display. Keep  E
 depressed until  SET Hold
disappears and the city code starts to fl ash.
2. Press  E
 to display the longitude/latitude setting screen, with the 
latitude setting fl ashing.
3. Use  D
 to move the fl...

9
Operation Guide 3173 3246
Illumination
The display of the watch is illuminated for easy reading in the dark.
The watch’s auto light switch turns on illumination automatically whe\
n 
you angle the watch towards your face.
• The auto light switch must be turned on for it to operate.
To turn on illumination manually
Press L
 in any mode to illuminate the display.
• You can use the procedure below to select either one second or three 
seconds as the illumination duration. When you press  L
, the display...

10
Operation Guide 3173 3246
Specifi cations
Accuracy at normal temperature:
 ±15 seconds a month
Timekeeping:  Hour, minutes, seconds, p.m. (P), year, month, day, day of the week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to\
 2099
Other: 3 display formats (Day of the week, Year, Barometric pressure gr\
aph); Home City code (can be  assigned one of 48 city codes); Standard Time / Daylight Saving Time (\
summer time)
Digital Compass:  20 seconds...