Casio Qt2100 User Manual

QT-2100
Versatile Intelligent Terminal
———————————————————————
Installation &
Down Recovery Manual
Version 1.0 February 2002
c
C
7
4
1
0
8
5
2
009
6
3
•
QT-2100 

Contents
I-2
This manual is intended for use as a reference to the QT-2100 system. It provides details to
install systems and down recovery. This manual does not describe actual programming,
which is covered in the QT-2100 programming manual.
This manual consists of the following chapters:
1. System installation
This chapter show the procedure of installing QT-2100 systems.
2. System down and recovery
This chapter explains actions to take and recovery methods when the system goes down.
Note: Casio...

I-3QT-2100 Installation & Down Recovery Manual 

Contents
I-4 

I-5QT-2100 Installation & Down Recovery Manual
1. System installation ........................................................................................ I-6
1-1. How to load IPL (Initial Program Loading) .................................................................. I-6
1-1-1. From PC to QT-2100 terminal via RS-232C ..................................................... I-6
1-1-2. From one QT-2100 to QT-2100 terminals via inline ......................................... I-7
1-1-3. From CF card...

I-6
System Installation
1. System installation
In this chapter shows how to install QT-2100 systems and peripherals.
1-1. How to load IPL (Initial Program Loading)
Normally, IPL is not necessary since QT-2100 has efficient program options to meet your
circumstances.
In some cases, you need to change the application program to meet your requirements, the
IPL is necessary to download the application program to QT-2100.
To load IPL, there are three methods:
1) From PC to QT-2100 terminal via RS-232C
2) From...

I-7QT-2100 Installation & Down Recovery Manual
1-1-2. From one QT-2100 to QT-2100 terminals via inline
1. Set up the system (refer to the left figure).
2. Initialize the target QT-2100 to receive the IPL data (refer to
the Machine initialization section of the Manager operation
chapter of QT-2100 Reference manual page 95.)
3. Execute IPL data sending operation (refer to the Auto-program
operation section of the Manager operation chapter of QT-
2100 Reference manual page 125.)
4. After IPL completion,...

I-8
System Installation
1-2. How to install QT-2100 system
1-2-1. QT-2100 stand alone system (with printer)
1. Set up the system (refer to the left figure).
2. Initialize the QT-2100 (refer to the Initialization chapter of
QT-2100 Programming manual page 8.)
Note 1:
If the QT-2100 cannot recognize the printer(s) correctly,
check the dip switches on the printer or printer cable and
try initialization operation again. Casio printer cable (PRT-
CB-8A/-8B) is required for proper recognition of the local...

I-9QT-2100 Installation & Down Recovery Manual
3. Initialize QT-2100 terminals one by one.
Note:
When you want to copy master program to satellites,
complete the master program, and then initialize the satel-
lite and receive the master program during initialization
procedure of satellites.
1-2-3. QT-2100 master/satellite system (with remote printer)
1. Set up the system (refer to the figure below).
2. Initialize the master QT-2100 (refer to the Initialization chap-
ter of QT-2100 Programming manual page...

I-10
System Installation
SW No. Function
Data reception error
Receive buffer capacity
Handshaking
Data word length
Parity check
Parity selection
Transmision speed
ON OFF
Ignored Prints ?
45 bytes 4k bytes
XON/XOFF DTR/DSR
7 bits 8 bits
Ye s N o
Even Odd
See transmission 
speed setting
Density setting
Light
DarkSW No.
3
ON
OFF
ON
OFF4
ON
OFF
OFF
ON
UP-350 Bottom view
DSW1DSW2
1
2
3
4
5
6
7
8
1
SW No. Function
Busy condition
Reserved
Print density
Reserved
Reserved
I/F 6 pin reset signal
I/F 25 pin reset...