Casio Xj-360 Data Projector Users Guide

DATA PROJECTOR 
XJ-360
User’s Guide
•Make sure you read all of the precautions in the 
printed “User’s Guide (Basic Operations)” first. 
Also see the “User’s Guide (Basic Operations)” 
for information about setting up the projector and 
replacing its lamp.
•Keep this manual in a safe place for future 
reference.
E 

 Digital Light ProcessingTM, DLPTM, Digital Micromirror DeviceTM, and DMDTM 
are trademarks of Texas Instruments Incorporated of the United States.
 Microsoft, Windows, Windows NT, Windows XP, and the Windows logo are 
registered trademarks or trademarks of Microsoft Corporation of the United 
States in the United States and other countries.
 Apple and Macintosh are registered trademarks of Apple Computer, Inc. of 
the United States.
 Other company and product names may be registered trademarks or...

Contents
3
Projection Operations .................................................................... 4
Projecting onto a Screen ................................................................................... 4
Keystone Correction (KEYSTONE)................................................................... 8
Using Color Mode (COLOR MODE) ............................................................... 11
Adjusting the Volume Level (VOL +/–) ...............................................................

Projection Operations
4
Projection Operatio ns
This section explains the basic steps for projecting an image.
Basic Flow
Projecting onto a Screen
Preparing the Projector Starting
Projection
Set up the projector and point it at the screen. 

 User’s Guide (Basic Operations): Setting Up the Projector
Connect the computer or video device to the projector.

 User’s Guide (Basic Operations): Connecting a Computer to the Projector

 User’s Guide (Basic Operations): Connecting to a Standard Video Device
Turn on...

5
Projection Operations
Auto Input Source Selection 
When you turn on the projector, it checks the status of each input source (whether or not 
the input source is sending a signal) in the sequence shown below. It automatically selects 
the first input source it finds that is sending an input signal, and projects the applicable 
image.
If the RGB input terminal is connected to a computer and the S-VIDEO input terminal is 
connected to a video deck and signals are being supplied by both, for example, the...

Projection Operations
6
Manually Selecting the Input Source
The procedure you should use to select the input source depends on whether you are using 
projector keys or remote controller keys.
zTo select the input source using projector keys, press the [INPUT] key on the projector to 
cycle through input sources in the sequence shown below.
zTo select the input source using remote controller keys, press the [RGB/COMPONENT], 
[VIDEO], or [S-VIDEO] key on the remote controller to select the input source you...

7
Projection Operations
Zoom and Focus
Use the zoom ring to adjust the image size, and the focus ring to focus the image.
zIt is best to have a still image on the screen when you focus the image.
zPerforming zoom after focusing can cause the image to go out of focus. If this happens, 
focus again.
Auto Adjustment of an RGB Image
When the input source is RGB (computer), the projector automatically adjusts vertical and 
horizontal positioning, frequency, and phase whenever it detects an RGB signal...

Projection Operations
8
When the projector is at an angle to the screen it is projecting on, the projected image may 
have different length top and bottom edges. This phenomenon is called, “keystoning”. This 
projector comes with functions for automatic as well as manual keystone correction, which 
provides a regularly shaped projected image. The following shows the allowable angle that the 
projector can be positioned relative to the screen.
zThe angles shown in the above illustration are subject to the...

9
Projection Operations
Automatic Keystone Correction 
Automatic keystone correction correct the image to counteract the effects of vertical keystoning.
Performing auto keystone correction causes the message “Auto Keystone Corrected.” to appear 
in the bottom center of the projected image.
zAuto keystone correction is performed by detecting the elevation angle of the projector. 
This means that the surface you are projecting onto needs to be standing straight up. If 
the surface you are projecting onto...

Projection Operations
10
Manual Keystone Correction
Manual keystone correction can be used to correct for vertical keystoning.
To use manual keystone correction
1.Press the [KEYSTONE] key.
zThis causes the keystone correction screen to appear on the projected image.
2.Use the [W] and [X] keys to correct for keystoning.
zEach press of [W] or [X] shifts the indicator on the currently selected bar left or right.
zKeystone correction is possible within the range that the indicator is able to move within 
the...